Русский dropdown-ico

Инструкция обслуживания Cisco Systems 8540 CSR

42 страниц 0.29 mb
Скачать

Перейти на страницу of 42

Summary
  • Cisco Systems 8540 CSR - page 1

    CHAPTER 4-1 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) 4 Configuring Interfaces This chapter describes basic interface conf igurations for your Layer 3 switch router . Also included are sections about conf iguring virtual LANs (VLANs), packet-ov er-SONET interf aces, A TM uplink interface ...

  • Cisco Systems 8540 CSR - page 2

    4-2 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Overview of Interface Configuration Overview of Interface Configuration A router’ s main function is to relay packets from one data link to another . T o do that, the characteristics of the interfaces throug ...

  • Cisco Systems 8540 CSR - page 3

    4-3 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces General Instructions for Configuring Interfaces Figur e 4-1 Interf ace P ort Identifier F or mat The interface port identif iers on the Ethernet modules remain the same regardless of whether other modules are ...

  • Cisco Systems 8540 CSR - page 4

    4-4 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Layer 3 Switching Interfaces Step 3 Follo w each interface command with the interface conf iguration commands required for your particular interface. The commands you enter def ine the protocols and appl ...

  • Cisco Systems 8540 CSR - page 5

    4-5 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Layer 3 Switching Interfaces Initially Configuring Gigabit Ethernet Interfaces T o conf igure an IP address and autonegotiation on a Gigabit Ethernet interface, perform the follo wing steps, beginning in ...

  • Cisco Systems 8540 CSR - page 6

    4-6 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Layer 3 Switching Interfaces Initially Configuring Fast Ethernet Interfaces Use the following procedure to assign an IP address to the F ast Ethernet 10BaseT or 100BaseT interface of your switch router s ...

  • Cisco Systems 8540 CSR - page 7

    4-7 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Layer 3 Switching Interfaces Examples The follo wing example sho ws sample output from the show interface gigabitether net command: Router# show interface gigabitethernet 0/0/0 GigabitEthernet0/0/0 is ad ...

  • Cisco Systems 8540 CSR - page 8

    4-8 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Virtual LANs About Virtual LANs V irtual LANs enable network managers to group users logically rather than by physical location. A virtual LAN (VLAN) is an emulation of a standard LAN that allows data tr ...

  • Cisco Systems 8540 CSR - page 9

    4-9 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring ISL VLAN Encapsulation Figur e 4-2 Example of an ISL VLAN Br idging Configur ation T o conf igure the Layer 3 VLANs sho wn in Figure 4-2, perform the follo wing steps, beginning in global conf igu ...

  • Cisco Systems 8540 CSR - page 10

    4-10 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring 802.1Q VLAN Encapsulation Example The follo wing example sho ws ho w to conf igure the interfaces for VLAN bridging with ISL encapsulation sho wn in Figure 4-2: Router(config)# interface fastether ...

  • Cisco Systems 8540 CSR - page 11

    4-11 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring 802.1Q VLAN Encapsulation Figur e 4-3 Example of Br idging Betw een Native and Non-Nativ e 802.1Q VLANs T o conf igure the bridging between nativ e VLAN 1 and non-nati ve VLAN 100 depicted in Figu ...

  • Cisco Systems 8540 CSR - page 12

    4-12 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Monitoring VLAN Operation Example The follo wing example sho ws ho w to conf igure the bridging between nativ e and non-nati ve 802.1Q VLANs shown in Figure 4-3: Router(config)# interface fastethernet 1/0/1.1 ...

  • Cisco Systems 8540 CSR - page 13

    4-13 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About the POS OC-12c Uplink Interface Because SONET/SDH (Synchronous Digital Hierarchy) is by def inition a point-to-point circuit, PPP is well suited for use ov er SONET links. The octet stream is mapped int ...

  • Cisco Systems 8540 CSR - page 14

    4-14 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Figure 4-5 sho ws an example of a service pro vider application of the POS OC-12c uplink interface module. Here traf f ic is aggregated from Catalys ...

  • Cisco Systems 8540 CSR - page 15

    4-15 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Default Configuration T able 4-1 sho ws the default conf iguration of an enabled POS OC-12c uplink interface. T o change any of these values, see th ...

  • Cisco Systems 8540 CSR - page 16

    4-16 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) T o initially conf igure the POS OC-12c uplink interface, perform the follo wing steps, beginning in global conf iguration mode: Example The follo w ...

  • Cisco Systems 8540 CSR - page 17

    4-17 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Additional Configurations T o conf igure additional properties to match those of the interface at the far end, perform the follo wing steps, beginni ...

  • Cisco Systems 8540 CSR - page 18

    4-18 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Configuring Framing The default framing mode for the POS OC-12c uplink interface is SONET STS-12c. Y ou can also conf igure the interface for SDH ST ...

  • Cisco Systems 8540 CSR - page 19

    4-19 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) The v alue of the c2 byte is determined as follows: • If the v alue of the c2 byte has not been explicitly conf igured with the pos f lag command, ...

  • Cisco Systems 8540 CSR - page 20

    4-20 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Configuring SONET Alarms The OC-12c POS uplink interface supports SONET alarm monitoring. T o conf igure alarm monitoring, perform the follo wing st ...

  • Cisco Systems 8540 CSR - page 21

    4-21 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Configuring SONET Delay Triggers A trigger is an alarm, which when asserted causes the line protocol to go down. Line and Section Triggers T able 4- ...

  • Cisco Systems 8540 CSR - page 22

    4-22 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) T o conf igure a delay in triggering the line protocol of the interface from going do wn, perform the following steps be ginning in global conf igur ...

  • Cisco Systems 8540 CSR - page 23

    4-23 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Examples The follo wing example sho ws output for the show interfaces pos command: Router# show interfaces pos 1/0/0 POS1/0/0 is up, line protocol i ...

  • Cisco Systems 8540 CSR - page 24

    4-24 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) The follo wing example sho ws output for the show contr ollers pos command: Router# show controllers pos 2/0/0 Interface POS2/0/0 Hardware is Packet ...

  • Cisco Systems 8540 CSR - page 25

    4-25 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) The follo wing example sho ws output for the show contr ollers pos command with the detail option: Router# show controller pos 2/0/0 detail Interfac ...

  • Cisco Systems 8540 CSR - page 26

    4-26 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the POS OC-12c Uplink Interface (Catalyst 8540) Interrupt Mask Register = 0x0001 Parity Error Register = 0x0000 Scratch Register = 0x80000000 Debug Register = 0x0000 CRC32 enabled, PPP enc, Diag c ...

  • Cisco Systems 8540 CSR - page 27

    4-27 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About ATM Uplinks (Catalyst 8540) SR1 72036 SR2 18806 SR3 0 SR4 0 SR5 0 MT1 15143 MT2 0 MT3 0 MT4 0 MT5 6 MT6 0 MT7 0 MT8 0 MT9 0 ST1 0 ST2 0 MRXS 262160 MTXS 16 SRXS 3 STXS 0 About ATM Uplinks (Catalyst 8540 ...

  • Cisco Systems 8540 CSR - page 28

    4-28 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Note The A TM uplink interface module does not work in a Catalyst 8540 MSR when the A TM router module is present. Configuring the ATM Uplink Interface (Ca ...

  • Cisco Systems 8540 CSR - page 29

    4-29 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) In addition, the A TM uplink interface uses the non-conf igurable values sho wn in T able 4-5. Initially Configuring the ATM Uplink Interface Y ou should c ...

  • Cisco Systems 8540 CSR - page 30

    4-30 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Example The follo wing conf iguration is an example of the tasks in the preceding table: Router(config)# interface atm 2/0/0 Router(config-if)# ip address ...

  • Cisco Systems 8540 CSR - page 31

    4-31 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Note The A TM uplink supports IP unicast and IP multicast fragmentation. For IP unicast fragmentation, the packet must ingress on a A TM interface and egre ...

  • Cisco Systems 8540 CSR - page 32

    4-32 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) T o conf igure the SONET ov erhead, perform the follo wing steps, beginning in global conf iguration mode: Note On the A TM OC-3c interface, you can conf i ...

  • Cisco Systems 8540 CSR - page 33

    4-33 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Configuring SONET Alarms The A TM OC-12c and the A TM OC-3c uplink interfaces support SONET alarm monitoring. T o conf igure alarm monitoring, perform the ...

  • Cisco Systems 8540 CSR - page 34

    4-34 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Configuring CDP The A TM uplink interface is conf igured by default with Cisco Discov ery Protocol (CDP) disabled. T o enable CDP , use the cdp enable comm ...

  • Cisco Systems 8540 CSR - page 35

    4-35 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) T o create a PVC, perform the follo wing steps, beginning in global conf iguration mode: The atm pvc command allo ws you to specify additional optional par ...

  • Cisco Systems 8540 CSR - page 36

    4-36 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) SVC Example In the following e xample, two switch routers with Layer 3 enabled A TM interfaces are connected by means of SVCs. For SVCs, the map-list assoc ...

  • Cisco Systems 8540 CSR - page 37

    4-37 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring the ATM Uplink Interface (Catalyst 8540) Example The follo wing example sho ws sample output for the show interfaces atm command. Router# show interfaces atm 0/0/0 ATM0/0/0 is down, line protocol ...

  • Cisco Systems 8540 CSR - page 38

    4-38 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces About Port Snooping Interface Configuration Mode: ATM clock line; STS-3c k1/k2 = 0/0 c2 = 0x13 Active Defects:None Alarm reporting enabled for:SF SLOS SLOF B1-TCA B2-TCA PLOP B3-TCA Active ATM Payload Defect: ...

  • Cisco Systems 8540 CSR - page 39

    4-39 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring Snooping Restrictions on Port Snooping The follo wing restrictions apply to port snooping: • The combined physical bandwidth of the source ports must not exceed the physical bandwidth of the des ...

  • Cisco Systems 8540 CSR - page 40

    4-40 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Configuring Snooping For a complete conf iguration example that includes port snooping, see the “Catalyst 8540 CSR with ISL, VLAN, and BVI with GEC” section on page C-1. T o disable port-based snooping on ...

  • Cisco Systems 8540 CSR - page 41

    4-41 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Monitoring Snooping Monitoring Snooping T o monitor the current snooping mode conf iguration and status, use the following commands: Now that you ha ve conf igured the interfaces on your switch router , see C ...

  • Cisco Systems 8540 CSR - page 42

    4-42 Layer 3 Switching Software Feature and Configuration Guide 78-6235-04, Cisco IOS Release 12.0(10)W5(18) Chapter 4 Configuring Interfaces Monitoring Snooping ...

Производитель Cisco Systems Категория Network Router

Документы, которые мы получаем от производителя устройства Cisco Systems 8540 CSR мы можем разделить на несколько групп. Это в частности:
- технические чертежи Cisco Systems
- инструкции обслуживания 8540 CSR
- паспорта изделия Cisco Systems
- информационные брошюры
- энергетические этикетки Cisco Systems 8540 CSR
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Cisco Systems 8540 CSR.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Cisco Systems 8540 CSR, инструкции обслуживания, короткие инструкции или инструкции пользователя Cisco Systems 8540 CSR. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Cisco Systems 8540 CSR.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Cisco Systems 8540 CSR, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Cisco Systems 8540 CSR пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Cisco Systems 8540 CSR.

Полная инструкция обслуживания Cisco Systems, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Cisco Systems 8540 CSR - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Cisco Systems 8540 CSR, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Cisco Systems 8540 CSR, которое найдем в данном документе
3. Советы по использованию основных функций устройства Cisco Systems 8540 CSR - которые должны облегчить нам первые шаги во время использования Cisco Systems 8540 CSR
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Cisco Systems 8540 CSR
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Cisco Systems 8540 CSR в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Cisco Systems 8540 CSR?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Cisco Systems 8540 CSR, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Cisco Systems 8540 CSR со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)