-
Patton electronic 2172R - page 1
USER MANUAL MODEL 2172R Ruggedized 50-Mbps Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2172R-UM Doc# 03333U2-004 Rev . A Revised 5/21/08 An ISO-9001Cer tified Company ...
-
Patton electronic 2172R - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Compliance ................................................................................... 4 EMC Compliance:......................................................................... 4 Safety Compliance: ................................... ...
-
Patton electronic 2172R - page 3
3 C Model 2172R Series Interface Pin Assignment ...................... 19 C.1 10/100Base-T Interface .............................................................. 19 RJ-45 .......................................................................................... 19 C.2 CopperLINK Interface .......................................................... ...
-
Patton electronic 2172R - page 4
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 2172R components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warranty is limited to def ects in w orkmanship or materials, and does not cov er customer damage, ab use or ...
-
Patton electronic 2172R - page 5
5 1.2 RADIO AND TV INTERFERENCE (FCC PART 15) This equipment generates and uses radio frequency energy , and if not installed and used properly—that is, in strict accordance with the manu- f acturer's instructions—may cause interf erence to radio and television reception. This equipment has been tested and found to comply with the limits f ...
-
Patton electronic 2172R - page 6
6 1.5 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service personnel. • Mains Voltage: Ensure that the external power adapter is a listed Limited Power Source. The mains outlet that is utilized to power the devi ...
-
Patton electronic 2172R - page 7
7 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or one year f or par ts and labor . If any questions or prob lems ar ise during installation or use of this product, contact P atton Electronics T echnical Suppor t at +1 (301) 975-1007 ...
-
Patton electronic 2172R - page 8
8 These units can automatically f orward LAN broadcasts , multicasts, and frames across a 2-wire v oice-grade twisted-pair link. The data is passed transparently (unmodified) through the 2172Rs or 2172s. The 2172Rs automatically add and delete MA C addresses, only passing pac kets across the CopperLINK link that are meant f or the remote peered LA ...
-
Patton electronic 2172R - page 9
9 Figure 2. Model 2172R standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2172R suppor ts communication between two peer Ethernet LAN sites ov er a distance of up to 6,000 ft (1.8 km) over 24 A WG (0.5 mm) twisted-pair wire. Note Actual distance and link performance ma y vary depending on the environment and type/gauge ...
-
Patton electronic 2172R - page 10
10 1. T o function properly , the two Model 2172Rs m ust be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Model 2172R is equipped with either an RJ-45 or a terminal block interf ace jack that ...
-
Patton electronic 2172R - page 11
11 3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The shielded RJ-45 por t labeled Ethernet is the A uto-MDIX10/100Base- T interf ace. This por t is designed to connect directly to a 10/100Base-T network. Figure 5 shows the signal/pin relationships on this interf ace. Y ou ma y connect this por t to a hub or PC using a straight through or cross ...
-
Patton electronic 2172R - page 12
12 4.0 CONFIGURATION The Model 2172R has eight DIP s witches f or configuring the unit for a wide variety of applications. This section descr ibes switch locations and e xplains the diff erent configurations. 4.1 CONFIGURING THE HARDWARE DIP SWITCHES Using a small flat-tip screwdriv er , remov e the protective co ver located on the underside of ...
-
Patton electronic 2172R - page 13
13 Figure 7. DIP switch orientation 4.2 CONFIGURING DIP SWITCH S2 DIP s witch S2 is where you configure the CopperLINK line r ate, symmet- ric or asymmetr ic, Ethernet, and Ether net Shutdown. T able 1 summa- rizes def ault positions of DIP s witches S2-1 through S2-8. Detailed descriptions of each switch f ollow the table . T able 1: S2 Summary P ...
-
Patton electronic 2172R - page 14
14 Switch S2-1: Symmetric/Asymmetric Operation Use s witch S2-1 to configure the unit f or symmetric or asymmetric opera- tion.. Switches S2-2 and S2-3: Data Rate Use s witches S2-1, S2-2 and S2-3 to configure the CopperLINK line rates. Switches S2-4, S2-5 and S2-6: Ethernet Configuration Use s witches S2-4, S2-5 and S2-6 to configure Ethernet ...
-
Patton electronic 2172R - page 15
15 Switch S2-7: Ethernet Shutdown Use s witch S2-7 to enable or disab le Ether net Shutdown. When Ether net Shutdown is enab led, the 2172R will disable the Ether net interf ace when there is no CopperLINK link detected. When Ether net Shutdown is dis- abled, the Ethernet interface will alw ays be enab led. Switch S2-8: Remote Configuration Use s ...
-
Patton electronic 2172R - page 16
16 5.2 FRONT PANEL LED STATUS MONITORS The Model 2172R f eatures three front panel LEDs that monitor power , the Ethernet signals, and the CopperLINK connection. Figure 8 shows the front panel location of each LED . T able 8 on page 16 describes the LED functions. Figure 8. Model 2172R standalone unit front panel T able 8: F ront panel LED descr ip ...
-
Patton electronic 2172R - page 17
17 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Shielded RJ-45, 10/100Base-T , IEEE 802.3 Ether net • CopperLINK Connection: RJ-45 or T erminal Block A.2 TRANSMISSION LINE T wo-wire unconditioned twisted pair. A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE • Line Rate: 50 Mbps, symmetric upstream/downstream. Additional symmetric and asymm ...
-
Patton electronic 2172R - page 18
18 APPENDIX B MODEL 2172R SERIES F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) P atton Model # Description Base Models 2172R/EUI Ruggedized 50-Mbps Ethernet Extender ; -10 to 70°C; UI 2172R/C/EUI Ruggedized 50-Mbps Ethernet Extender ; -10 to 70°C; conf or mal coated (humidity 85% condensing ...
-
Patton electronic 2172R - page 19
19 APPENDIX C MODEL 2172R SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection T erminal Block Figure 1. Model 2172R (T erminal Block) twist ...
-
Patton electronic 2172R - page 20
20 APPENDIX D DISTANCE CHAR T, BASED ON 24 A WG (0.5 MM) Note The actual distance and link performance ma y vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Cop yright © 2008 P atton Electronics Company All Rights Reser ved. Symm Line Rate Distance in feet (km) Throughput at Max Distance 50 Mbps 80 ...
У вас вопрос, касающийся Patton electronic 2172R?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Patton electronic 2172R, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Patton electronic 2172R со всей вероятностью он захочет поделиться методом ее решения.