-
Microtek MS4 - page 1
Conference Projectors www .microtek.com User's Manual MS4 DLP Projector ...
-
Microtek MS4 - page 2
Copyright This publication, including all photographs, illustrations and software, is protected under international cop y- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright J uly , 2004 Disclaimer The information in this document ...
-
Microtek MS4 - page 3
Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situa tions. The following boxes are used in this manual to alert you to important inform a tion. Note: Provides additional information on the topic at hand. Important: Provides additional information that should not be overlooked. Caution: Alerts you to ...
-
Microtek MS4 - page 4
Remote Control The remote control has a laser for pointing out items on a screen. DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently. General Safety Informati on Ø Do not open the unit case. Aside from the projection lamp, there are no user - serviceable parts in the unit. For servicing, contact qualified service ...
-
Microtek MS4 - page 5
Table of contents GETTING STARTED ................................................................................................................................................................ ............. 1 P ACKING C HECKLIST ....................................................................................................................... ...
-
Microtek MS4 - page 6
G ETTING S TARTE D Packing Checklist Carefully unpack the projector and check that the following items are i n cluded: P o w e r M e n u K e y s t o n e A u t o E n t e r S o u r c e V o l u m e M u t e F r e e z e 1 2 DLP PROJECTOR R EMOTE CONTROL ( WITH T WO AAA BATTERIES ) P OWER CORD USB CABLE S - VIDEO CABLE A UDIO CABLE ( MINI JACK - TO - RCA ...
-
Microtek MS4 - page 7
Views of Projector Parts Front - right view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Lens/focus turn the lens to focus 14 2. IR receiver Receiver for IR signal from remote control 9 3. Connectors Connect input/output devices 5 4. AC socket Socket for power cord 12 5. Side foot 6. Height adjuster Adjusts level of projector 7. Height adjuster button ...
-
Microtek MS4 - page 8
Top view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Image - focus co n trol 14 2. Zoom Enlarge or shrink the projected image 14 3. Power Turns the projector on or off 12 4. System status LEDs (next page) 5. OSD navigation buttons (next page) 4 6. Source Detects the input device 12 7. Menu Opens the On - Scre en Display (OSD) 16 8. Auto Optimizes imag ...
-
Microtek MS4 - page 9
Top view — OSD buttons and LEDs I TEM L ABEL D ESCRIPTION S EE PAGE : Green U nit is powered on and working correctly Off Unit is powered off 1. Power (LED) Flashing Operational error code (refer to “LED Error Messages” on page 30 ) Orange Lamp ready — you can safely turn on or off the pr o jector 2. Ready (LED) Fl ashing Lamp not ready — ...
-
Microtek MS4 - page 10
Connectors view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Audio - in Connect the audio cable (supplied) from the input device 11 2. RS - 232 Reserved service port for firmware upgrades 3. DVI -I Conn ect the DVI cable (supplied) from a computer 11 4. Kensington Lock Secure to permanent object with a Kensington Lock system 28 5. USB Connect the USB c ...
-
Microtek MS4 - page 11
Bottom view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Projection lamp cover Remove when changing lamp 24 2. Height a d juster 3. Side foot Adjust level of the projector 13 4. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling. CAUTION : With ceiling installatio n, use approved mounting hardware & M4 ...
-
Microtek MS4 - page 12
Remote Control Parts Important: 1. Avoi d using the projector with bright fluorescent lighting turned on. Certain high - frequency flu o- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path b e- tween remot e and projector is obstructed, you can bounce ...
-
Microtek MS4 - page 13
I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Laser Use as on - screen pointer. DO NOT POINT IN EYES. 2. IR transmitter Transmits signals to projector 3. Status LED Lights when the remote is used 4. Auto Auto adj ustment for phase, tracking, size, position 5. Blank Makes the screen blank 20 6. Enter Changes settings in the OSD 7. Up cursor Navigates and ...
-
Microtek MS4 - page 14
Remote Control Operating Range The remote control uses infrared transm ission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about (10) meters (33 feet) and 3 ...
-
Microtek MS4 - page 15
S ETUP AND O PERATION Inserting the Remote Control Bat tery 1. Remove the battery compartment cover by sliding the cover in the direction of the a r row. 2. Insert the supplied batteries taking note of the polarity (+/ - ) as shown here. 3. Replace the cover. Caution: 1. Only use AAA alkaline batteries. 2. Di spose of used batteries according to lo ...
-
Microtek MS4 - page 16
Connecting Input Devices A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector. I TEM L ABEL D ESCR ...
-
Microtek MS4 - page 17
Starting and Shutting down the Projector 1. Connect the power cord to the proje c- tor. Connect the other end to a wall outlet. The Power LED and Lamp - ready LED turn on. 2. Turn on the connected d e vices. 3. Ensure the Lamp - ready LED is on a steady (not flashing) orange and then press the Power button to turn on the projector. The projector sp ...
-
Microtek MS4 - page 18
Adjusting the Projector Level Take note of the following when setting up the proj ector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Be sure cables are not in the way or can cause the projector to be knocked over. 1. To raise the level of the projector, lift ...
-
Microtek MS4 - page 19
Adjust the Zoom, Focus and Keystone 1. Use the Image - focus co n- trol (on the projector only) to sharpen the pr o jected image . 2. Use the Image - zoom co n- trol (on the projector on ly) to resize the projected i m- age and screen size . 3. Use the Keystone buttons (on the projector or the remote control) to correct i m age - trapezoid (wider t ...
-
Microtek MS4 - page 20
Adjusting the Volume 1. Press the Volume +/ - bu t- tons on the projector or the remote control. The volume control a p- pears on the display. 2. Use the Volume +/ - bu t- tons to adjust the level. 3. Press the Mute button (on the remote control only) to turn off the volume. 4. Press any Volume +/ - bu t tons on the projector or the remote control ...
-
Microtek MS4 - page 21
O N - S CREEN D ISPLAY M ENU S ETTINGS On - Screen Display Menu Controls The projector has an On - Screen Display (OS D) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration sh ...
-
Microtek MS4 - page 22
Setting the OSD Language You may want to reference the OSD on your projec tor while reading this section. Set the OSD la n- guage to your preference before continuing. (The d e fault language is English.) 1. Press the Menu button. The Main menu appears. 2. Press the cursor button until Language is highlighted. 3. Press the cursor but ton until the ...
-
Microtek MS4 - page 23
Main Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Mai n menu. Press the cursor button to move up and down in the Main menu. I TEM D ESCRIPTION D EFAULT Brightness Press the cursor button to adjust the brightness. (Range: 0 — 100) 50 Contrast Press the cursor button to adjust the contrast. (Range: 0 — 1 ...
-
Microtek MS4 - page 24
Setup Menu Press the Menu button to o pen the OSD menu. Press the cursor button to move to the Setup menu. Press the cursor button to move up and down in the Setup menu. I TEM D ESCRIPTION D EFAULT Horizontal Pos i tion Press the cursor button to move the image left or right. (Range: 0 — 100 ) 50 Vertical P o- sition Press the cursor button to mo ...
-
Microtek MS4 - page 25
Config Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Co n fig menu. Press the cursor button to move up and down in the Config menu. I TEM D ESCRIPTION D EFAULT Blank Screen Press the cursor button to select a background color for blank screen (Range: Black – Red – Green – Blue – White) Blue Auto So ...
-
Microtek MS4 - page 26
Utility Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Utility menu. Press the cursor button to move up and down in the Utility menu. I TEM D ESCRIPTION D EFAULT Video Type Press the cursor button to select the Video standard (Range: Auto – NTSC – PAL – SECAM) Auto Video AGC Press the cursor button to ...
-
Microtek MS4 - page 27
Language Menu Press the Menu button to open the Main menu. Press the cursor button to move to the La n- guage menu. Press the cursor button to move up and do wn in the Language menu. I TEM D ESCRIPTION D EFAULT English French German Italian Spanish Swedish Chinese Simpl i fied Chinese Trad i tional Japanese Korean Press the cursor button to move up ...
-
Microtek MS4 - page 28
Status Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Status menu. Press the cursor button to move up and down in the Status menu. I TEM D ESCRIPTION D EFAULT Video Inform a tion Displays the resolution and refresh rate of the connected video d e vice. Active Source Displays the active source. Software Ve r ...
-
Microtek MS4 - page 29
M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified repl acement part, which you can order from your local dealer. Important: 1. The lamp contains a certain amount of mercury and should be disposed of according to local o r- dinance regulation ...
-
Microtek MS4 - page 30
3. Remove the two screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the mo d- ule handle to r e move the lamp mo d ule. 6. R everse steps 1 to 5 to install the new lamp module. ...
-
Microtek MS4 - page 31
Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the Menu button to open the Main menu. 2. Press the cursor button to move to the Status menu. 3. Press the cursor button to move down to Lamp Hour Reset . 4. Press the button. A message screen a p pears. 5. Press the cursor ...
-
Microtek MS4 - page 32
Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure tro u ble - free operation. Warning: 1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation opening ...
-
Microtek MS4 - page 33
Cleaning the Case Refer to the following to clean the projector case. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and wipe the case. 3. Rinse all detergent from the c loth and wipe the projector again. Caution: To prevent discoloration or fading of the case, do ...
-
Microtek MS4 - page 34
T ROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projecto r. If the problem remains unsolved, contact your dealer for a s sistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose co n- nection. Check the following bef ...
-
Microtek MS4 - page 35
LED Error Messages LED S TATUS / NUMBER OF FLASHES D ESCRIPTION Flashing Lamp not ready — do not press the power bu t ton 1 Power fan error 2 Lamp fan error Lamp - ready 3 Blower error 3 System overheating 4 System interface error 5 Lamp error 6 Fan error (refer to Lamp ready status to dete r mine which fan) 7 Lamp cover open Power 8 DLP driver e ...
-
Microtek MS4 - page 36
Problem: The image is flat with no co ntrast 1. Adjust the Contrast setting on the Main menu of the OSD. Problem: The color of the projected image does not match the source image. 1. Adjust the Color Temp. and Gamma settings on the ColorMgr menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is ...
-
Microtek MS4 - page 37
trying to fix the problem. The information may be useful to the service personnel. Return the projector to the place you purchased it. ...
-
Microtek MS4 - page 38
S PECIFICATIONS Specifications Display type TI DMD 0.55 - inch x 1, 12 degrees, DDR DLP Resolution SVGA 800 x 600 Native Color 16.7 Million (24 - bits/Pixel) Bandwidth Up to XGA 1024x768 @60 Hz Weight 2.0 kg (4.5 lbs.) Projection distance 1.5 to 7 meter Projection screen size 37 inches to 202.8 inches Brightness unifor m ity 80% Projection lens Man ...
-
Microtek MS4 - page 39
Input/output connectors DVI - I PC USB Composite video (RCAx1) Video S - Video (Mini - DIN) Audio Mini - jack Service/upgrades RS - 232 Security Kensington slot ...
-
Microtek MS4 - page 40
Projection Distance V.S. Projection Size L Projection distance S c r een h e i gh Screen Width A B C D Max. Screen Size Min. Screen Size Proje c- tion Distance Diagonal Width Height Diagonal Width Height L A C B D 1.5m 1.10m 0.88m 0.66m 0.94m 0.75m 0.56m 4.92' 43.3" 34.6" 26.0" 37.0" 29.5" 22.0" 2.0m 1.47m 1.17m 0 ...
-
Microtek MS4 - page 41
Timing Charts The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. Table 2: ANALOG Computer Timings (Resolution and Refresh R ate 【 fV 】 ) Resolution FH (kHz) FV (Hz) Signal mode 640 x 480 31.47 59.94 Expanded VGA 640 x 480 37.86 72.81 Expanded VGA 640 x 480 37. 50 7 ...
-
Microtek MS4 - page 42
Dimensions 28.0 cm (11.02 in.) 9 . 7 c m ( 3 . 8 1 i n . ) 21 . 7 c m ( 8 . 5 4 i n . ) ...
-
Microtek MS4 - page 43
R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pu r- suant to Part 15 of the FC C Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a co m mercial environment. This equipment generates, ...
У вас вопрос, касающийся Microtek MS4?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Microtek MS4, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Microtek MS4 со всей вероятностью он захочет поделиться методом ее решения.