-
QSC DSP 322UA - page 1
TD-000199- 00 rev .A *TD-000199-00* DSP 322ua 8x8 Signal Processor Hardware Manual ...
-
QSC DSP 322UA - page 2
2 IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLS The lightning flash with arrowhead symbol wit hin an equilateral tri angle is intended to al ert the user to the presence of uninsula ted “dangerous” voltage within the product’ s enclosure t hat may be of sufficien t magnitude to constit ute a risk of electri c shock to humans. The ...
-
QSC DSP 322UA - page 3
3 Introduction 1- Power indicator 2- Diagnostic indicator 3- Network status indicators 4- Sinal presence indicators 5- Multi-function push buttons 6- Display 7- Rotary select/accept knob 8- Safe Mode switch (recessed) 9- Analog outputs 10- mic/line inputs 11- Relay outputs 12- Logic outputs 13- Omni inputs 14- RS-232 port 15- Network status indicat ...
-
QSC DSP 322UA - page 4
4 regardless of the DSP configur ation, unless the configura- tion intentionally adds more delay . Both software and firmware can be easily updated over the network. In the future, QSC will be adding new capabilities to QSControl.net. Our latest code releases and access to up- to-date information on QSControl.net are available at www .qscontrol.net ...
-
QSC DSP 322UA - page 5
5 Introduction - Networ king the DSP 322ua Notes on Network Sy stem Design: As with any communications system, the reliability and performance of a local area network (LAN) is intimately related to the designer's skill and knowledge in implementing a topology that is robust, efficient and standards-compliant. Proper network des ign is even mor ...
-
QSC DSP 322UA - page 6
6 Example #2 - Connection to an Unmanaged Switch: Switches can be connected to other switches to build larger ne tworks; all of the normal networking principles apply . Here all Q SCon- trol.net traffic resides on a single unmanaged Ethernet switch. The DSP 322ua connects directly to the switch. A computer hosti ng a QSControl.net server applicatio ...
-
QSC DSP 322UA - page 7
7 Example #3 - Connecti on to a Managed Switch: This example illustrates a connection with a managed Ethernet switch. The switch is configured with multiple virtual local area networks (VLANs). Ethernet deliveries can onl y reach destination ports belonging to the same VLAN from which it was sourced. The figure shows a separate VLAN for QSCon trol. ...
-
QSC DSP 322UA - page 8
8 Unpacking There are no special unpacking precautions. However , it is recommen ded you keep the original packing material for reuse in the rare event that service be required. If service is required and the original packing material is not available, ensure that the unit is adequately protected for shipment (strong box of appropriate size, suffic ...
-
QSC DSP 322UA - page 9
9 Computer Requirements & Software Installation Installing QSControl.net is easy . All you need to do is choose th e folder where the program is to be stored (the default settin g is accept- able for most applications). We recommend your syste m meet the following minimum requirements: 1- IBM PC compatible computer with a Pentium 4 processor . ...
-
QSC DSP 322UA - page 10
10 Connections AC Power Cord Insert the molded receptacle of the AC power cord into the AC power inlet on the back of the DSP 322ua. Plug the AC line connec- tor into the AC outlet. The power supply will accept from 100 to 240 V olts AC, 47 to 440 Hertz, without any changes. If a different type of IEC power cord is required than the one supplied wi ...
-
QSC DSP 322UA - page 11
11 Relay Out T wo sets of relay contacts are provided, RELA Y OUT 1 and RELA Y OUT 2. Contacts are floating and rated for 30VDC, 1A. There is one common terminal, one normally-closed contact terminal and one normally-open contact terminal. These are labeled as C, NC and NO on the rear panel. When the relay is not energized, the C terminal is connec ...
-
QSC DSP 322UA - page 12
12 LED Indicators (continued) QSControl Status (Po rt) Indicators- There are three LEDs on the front and rear panels labeled RX, TX and LINK. These indicate the status for the QSControl.net netwo rk. Their functions are described below . RX (receive) - This indicator illuminates any time the DSP 322ua receives data from the network. TX (transmit)- ...
-
QSC DSP 322UA - page 13
13 LCD Navigation Map Left si de button s have scr een depe ndent fun ctions. This read-only screen is the “out of the box” default display after power up. Th is is the most desired information when first sett ing up a network system. Once user moves to a differ ent screen, the last screen accesse d becomes the new power up default. Boot Screen ...
-
QSC DSP 322UA - page 14
14 Getting Started This section outlines one of the simpler methods of getting fam iliar with your DSP 322ua and the QSControl.net software. The go al of this procedure is to get your computer and the DSP 322ua conne cted and communicating and the QSControl.net software installed a nd running. After the software is installed and running, refer to t ...
-
QSC DSP 322UA - page 15
15 Getting Started (continued) 17- Select Device , Add Device , from the menu. A new window will open prompting you to name the device. Name it logically , such as DSP 1, or similar . Select the Device T ype and select DSP 322ua. At the Password prompt, ent er “qsc” (lower case, no quotatio n marks). This is the device password, separate from t ...
-
QSC DSP 322UA - page 16
16 Operation QSControl Port The QSControl port operates on a 10BaseT Ethernet network. This por t is one of the primary means for connecting QSControl.net to the DSP 322ua. The port may connect directly to a PC's 10BaseT or 10/100 (auto-sensing or auto-negotiating) network interface card using a crossover cable. Data from the QSControl port ma ...
-
QSC DSP 322UA - page 17
17 Utility/Diagnostic Fu nctions (continued) RS-232 Communications Procedure: 1) Connect the RS-232 port of the DSP 322ua to an unused serial port (COM port) of a PC using a normal (straight-through) serial cable. 2) Open the HyperT erm inal program. This program is usually started by clicking the Windows Start icon, selecting Programs , then Acces ...
-
QSC DSP 322UA - page 18
18 Preliminary Specification IN OUT THRU Dynamic Range (A ES-17, -60dB Method, all sensit ivities) unweighted >110dB >112dB >108dB A weighted >113dB >115dB >111dB Distortion (20Hz-20 KHz, all sen sitivities) Gain= 0 - 30dB <0.008% THD+N <0.009% THD+N <0.009% THD+N Gain >30dB <0.05% THD+N <0.009% THD+N <0.05% T ...
-
QSC DSP 322UA - page 19
19 Preliminary Specification Relay Outputs 2 discrete floating relay switch outputs Connector T ype 3-pin "Phoenix Style" (a.k.a . "Euro Style") detachable terminal blocks Configuration Electromechanical Relay Pinout 1:NC 2:NO 3: COM Switching Capacity (nom) 1A 30VDC Logic Outputs 4 discrete outputs Connector T ype 2-pin "P ...
-
QSC DSP 322UA - page 20
QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2005 “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elephone Numbers: Main Number (714) 754-6 ...
У вас вопрос, касающийся QSC DSP 322UA?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с QSC DSP 322UA, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с QSC DSP 322UA со всей вероятностью он захочет поделиться методом ее решения.