Русский dropdown-ico

Инструкция обслуживания Dolmar PS6400-45

32 страниц Не касается
Скачать

Перейти на страницу of 32

Summary
  • Dolmar PS6400-45 - page 1

    1 Instruction Manual Original Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! http://www .dolmar .com PS-6400, PS-6400 H PS-7300, PS-7300 H PS-7900, PS-7900 H ...

  • Dolmar PS6400-45 - page 2

    2 T able of contents Page Packing ................................................................................ 2 Delivery inventory .............................................................. 3 Symbols ............................................................................... 3 SAFETY PRECAUTIONS General precautions .................... ...

  • Dolmar PS6400-45 - page 3

    3 STOP 1 4 5 6 7 3 2 8 Delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Offset screwdriver 7. Screwdriver for carburetor adjustment 8. Cylinder Þ n cleaner 9. Instruction manual (not shown) In case one of the parts listed should not be included in the delivery inventory , please consult you ...

  • Dolmar PS6400-45 - page 4

    4 4 5 6 7 1 2 3 1 SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followung uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinning. - Hobbyklasse: Occasional use on ...

  • Dolmar PS6400-45 - page 5

    5 6 5 7 9 8 Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5). - Let the engine cool down before refuelling. - Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. Always wear protective gloves when refuelling. Frequently ...

  • Dolmar PS6400-45 - page 6

    6 Kickback - When working with the chain saw dangerous kickbacks may occur . - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - This causes the saw to be thrown back toward the user with great force and out of control. Risk of injury! In order to prevent kickback, follow these ...

  • Dolmar PS6400-45 - page 7

    7 - Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever possible. The chain saw will then be pushed away from y ...

  • Dolmar PS6400-45 - page 8

    8 SERVICE T ransport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inadvert- ent start of the chain. - Never carry or transport the chain saw with the chain running. - When transporting the chain saw over long distances the guide bar protection cover (delivered with ...

  • Dolmar PS6400-45 - page 9

    9 Denomination of components 1 Handle 2 Filter hood 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muf ß er 7 Spike bar 8 Chain tensioning screw 9 Retaining nuts 10 Chain catch 11 Sprocket guard 12 Identi Þ cation plate 13 Starting valve (option) 14 Starter grip 15 Adjusting screws for carburetor 16 I/STOP-switch 17 ...

  • Dolmar PS6400-45 - page 10

    10 5 7 6 4 5 1 2 3 Lift the chain ( 6 ) over the sprocket ( 5 ). Using your right hand, guide the chain into the top guide groove on the guide bar ( 7 ). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar ( 4 ) and push against the sprocket ( 5 ) as shown by the arrow . M ...

  • Dolmar PS6400-45 - page 11

    11 2 13 3 11 12 6 8 9 10 Guide the chain over the chain catch ( 9 ). Pull the guide bar as shown by the arrow to take the slack out of the chain, so that it comes up to the bottom edge of the guide bar ( 10 ). Pull the chain ( 6 ) around the sprocket nose ( 8 ) of the guide bar in the direction of the arrow . G H Tightening the saw chain Slightly l ...

  • Dolmar PS6400-45 - page 12

    12 ST OP 2 13 1 2 1 Checking the chain tension The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand. While doing so the chain brake must be released. Check the chain tension frequently - new chains tend to get longer during use! When checking the chain tension the eng ...

  • Dolmar PS6400-45 - page 13

    13 Chain oil Use an oil with adhesive additive for lubricating the chain and guide bar . The adhesive additive prevents the oil from being ß ung off the chain too quickly . We recommend the use of chain oil which is bio-degradable in order to protect the environment. The use of bio-degradable oil may even be required by local regulations. The chai ...

  • Dolmar PS6400-45 - page 14

    14 Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. The engine must be switched off! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel or oil tank. Unscrew the cap and Þ ll the tank with fuel (fuel/oil mixture) or chain oil as the case may be. Fill up to the bottom edge of t ...

  • Dolmar PS6400-45 - page 15

    15 1 2 3 Checking the chain lubrication Never work with the chain saw withoute suf Þ cient chain lubri - ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the engine? ...

  • Dolmar PS6400-45 - page 16

    16 Starting the engine Start the chain saw only after having assembled it com- pletely and inspected. Move at least 3m away from the place where you fuelled the saw . Make sure you have a good footing, and place the saw on the ground in such a way that the chain is not touching anything. Engage the chain brake (lock). Hold the tubular handle tightl ...

  • Dolmar PS6400-45 - page 17

    17 D Adjusting the carburetor CAUTION: Carburetor adjustment may only be done by a specialist DOLMAR service centre! Only adjusting screw (S) can be manipulated by the user . If the saw chain moves in idle (i.e. without the throttle being pressed) , it is imperative to correct the idle speed! Do not adjust the idle speed until after complete assemb ...

  • Dolmar PS6400-45 - page 18

    18 E Working in winter In order to prevent carburetor icing in conditions of low tempe- rature combined with high humidity , and below + 5°C in order to get up to operating temperature faster , heated air can be taken from the cylinder . Remove the Þ lter hood (see „Cleaning air Þ lter“) Remove the insert ( 10 ) and insert it as shown in pos ...

  • Dolmar PS6400-45 - page 19

    19 The sharpening angle of 25° must be identical for all cutters! Different angles result in a roughly , irregularly running chain, increase wear and tear and cause chain beakage. The front rake 60° of the cutter results from the cut depth of the round Þ le. If the proper Þ le is used in the right manner, the correct front rake will be obtained ...

  • Dolmar PS6400-45 - page 20

    20 1 2 Files and how to work with them Sharpen using a special Þ le holder with a saw chain round Þ le. Normal round Þ les are not appropriate for this work. See „Accessories“ for the order number . File the Þ rst cutter half with a 5.5 mm dia. round saw-chain Þ le, then switch to a 4.8 mm dia. Þ le. The Þ le should cut only when pushed ...

  • Dolmar PS6400-45 - page 21

    21 8 10 11 7 5 4 5 1 6 7 2 3 Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „Replacing the spark plug“) . Always wear protective gloves! CAUTION: Start the chain saw only after having assembled it completely and in ...

  • Dolmar PS6400-45 - page 22

    22 12 16 15 13 17 Replacing the saw chain CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare-parts list) ! Check the sprocket before mounting a new chain. Worn out sprockets ( 12 ) may damage the new chain and must therefore be replaced. Remove the sprocket guard ( 1 ) (See „PUTTING INTO OPE- RA TION“ ...

  • Dolmar PS6400-45 - page 23

    23 3 5 4 CAUTION: T o prevent eye injury , always wear eye protection when cleaning the Þ lter with compressed air! Do not use fuel to clean the air Þ lter . Unhook the Þ lter hood clips ( 1 ) with the combination tool and remove the Þ lter hood ( 2 ). Pull out the choke ( 3 ) to prevent dirt particles from getting into the carburetor . Unhook ...

  • Dolmar PS6400-45 - page 24

    24 10 Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work. A hot engine can cause burns. W ear protective gloves! The spark plug must be replaced in case of damage to the insulator , electrode erosion (burn) or if the electrodes ...

  • Dolmar PS6400-45 - page 25

    25 11 Replacing the starter cable / Replacing the return spring Unscrew three screws ( 1 ). Remove fan housing ( 2 ). NOTE: The screws ( 1 ) are secured against falling out of the housing. CAREFUL! Injury hazard! Do not unscrew screw (5) if the return spring is under tension. If the starter cable is to be replaced although it is not broken, it will ...

  • Dolmar PS6400-45 - page 26

    26 13 15 16 14 Cleaning the cylinder area Remove the Þ lter hood and air Þ lter . Remove the spark plug cap and unscrew the spark plug. Press in the starting valve and activate the chain brake. Push the cable cutout and ignition cable out sideways. Unscrew the two rearmost screws on the cover . Unscrew the screws on the handguard pivot and remove ...

  • Dolmar PS6400-45 - page 27

    27 Instructions for periodic maintenance T o ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be pe r- formed regularly . Guarantee claims can be recognized only if this work is performed regularly and properly . Failure to perform the prescribed maintenance work can lead to acci ...

  • Dolmar PS6400-45 - page 28

    28 Spare parts Reliable long-term operation, as well as the safety of your chain saw , depend among other things on the quality of the spare pa rts used. Use only original DOLMAR parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, function and safety . Original spare parts and accessories c ...

  • Dolmar PS6400-45 - page 29

    29 15 10 11 9 16 4 8 7 6 5 13 20 21 22 23 24 27 25 1 2 3 12 14 10 11 17 28 Extract from the spare parts list Use only original DOLMAR parts. For repairs and replacement of other parts, see your DOLMAR service centre. Pos. DOLMAR-No. Qty . Denomination 1 415 038 655 1 Sprocket nose bar 38 cm (15“) 415 045 655 1 Sprocket nose bar 45 cm (18“) 415 ...

  • Dolmar PS6400-45 - page 30

    30 EU Conformity Declaration The undersigned, T amiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the DOLMAR machines, T yp: 038, 039, 040 Chain saw EU prototype test certi Þ cate No. PS-6400 (040) 481 1004.1 1012 PS-7300 (039) 481 1004.1 1012 PS-7900 (038) 481 1004.11012 manufactured by DOLMAR GmbH, Jenfelder Str . 38, ...

  • Dolmar PS6400-45 - page 31

    31 ...

  • Dolmar PS6400-45 - page 32

    32 Form: 995 701 221 (2012-06 GB) 106 Speci Þ cations subject to change without notice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .dolmar .com To Þ nd your local distributor, please visit www .dolmar .com ...

Производитель Dolmar Категория Chain saw

Документы, которые мы получаем от производителя устройства Dolmar PS6400-45 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Dolmar
- инструкции обслуживания PS6400-45
- паспорта изделия Dolmar
- информационные брошюры
- энергетические этикетки Dolmar PS6400-45
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Dolmar PS6400-45.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Dolmar PS6400-45, инструкции обслуживания, короткие инструкции или инструкции пользователя Dolmar PS6400-45. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Dolmar PS6400-45.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Dolmar PS6400-45, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Dolmar PS6400-45 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Dolmar PS6400-45.

Полная инструкция обслуживания Dolmar, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Dolmar PS6400-45 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Dolmar PS6400-45, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Dolmar PS6400-45, которое найдем в данном документе
3. Советы по использованию основных функций устройства Dolmar PS6400-45 - которые должны облегчить нам первые шаги во время использования Dolmar PS6400-45
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Dolmar PS6400-45
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Dolmar PS6400-45 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Dolmar PS6400-45?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Dolmar PS6400-45, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Dolmar PS6400-45 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)