-
Craftsman 315.27119 - page 1
Owner's Manual iP R 0 F E S S I 0 H A L I 6-1/2 in. (165 mm) 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW Model No 315.271190 Save this manual for future reference ,_ CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears Roebuck and Co., Hoffman Estates, IL 60 ...
-
Craftsman 315.27119 - page 2
TABLE OF CONTENTS • General Safety Rules .............................................................................................................................................. 2-3 • Specific Safety Rules/Symbols .............................................................................................................................. ...
-
Craftsman 315.27119 - page 3
Tool Use and Care • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is d ...
-
Craftsman 315.27119 - page 4
Additional Specific Safety Rules • DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle or motor housing, If both hands are holding the saw, they cannot be cut by the blade. • Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to j ...
-
Craftsman 315.27119 - page 5
Important Safety Instructions For Charger Save these instructions. This manual contains important safety and operating instructions for battery charger item nu tuber 9-11040 (981399-001 ). Following this rule will reduce the risk of electric shock, fire, or serious personal injury. Before using battery charger, read all instructions and cautionary ...
-
Craftsman 315.27119 - page 6
SYMBOLS SYMBOL NAME DESIG NATION/EXP LANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time "_, Alternating Current Type or a characteristic of current --=- Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute ...
-
Craftsman 315.27119 - page 7
KNOW YOUR TRIM SAW See Figure 1. Before attempting to use your trim saw, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench storage. _k WARNING: Carefully read through this entire owner&a ...
-
Craftsman 315.27119 - page 8
BLADE WRENCH (5 mm HEX KEY) BLADE WRENCH STORAGE AREA DEPTH OF CUT ADJUSTMENT (DEPTHADJUSTMENT KNOB) LOCK-OFF BUTTON SWITCH TRIGGER BATTERY PACK SPINDLE LOCK BUTTON RIP GUIDE SCREW (WING SCREW) UPPER SLADEGUARD LOWER BLADE GUARD HANDLE BEVEL CUT ADJUSTMENT (BEVEL ADJUSTMENT KNOB) BLADE BASE ASSEMBLY LOWER BLADE GUARD RIPGUIDE Fig. 1 8 ...
-
Craftsman 315.27119 - page 9
LED FUNCTION OF CHARGER YELLOW LIGHT "ON" AND RED LIGHT FLASHING INDICATES DEFECTIVE BA'I-rERY PACK CHARGER MOUNTING CHARGER See Figum4. Your charger has a "key hole" hanging feature for conve- nient, space saving storage. Therefore, if desired, you can mount your charger to a wall. Screws should be installed so that center ...
-
Craftsman 315.27119 - page 10
,_ WARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury. Note: Your saw is assembled with the battery pack a_ached. TO REMOVE BATTERY PACK See Fi ...
-
Craftsman 315.27119 - page 11
TO REMOVE BLADE See Figure 7. • Remove battery pack from saw. _1, WARNING: Failure to remove battery pack from saw could result in accidental starting causing possible serious personal injury. • Remove blade wrench from storage area. See Figure 1. • Position saw as shown in figure 8, depress spindle lock button, and remove blade screw. Note: ...
-
Craftsman 315.27119 - page 12
_1, WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you sho ...
-
Craftsman 315.27119 - page 13
SAW BLADES The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on your saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available. Gum and wood pitch hardened on blades will slow your saw down. Use gum and p ...
-
Craftsman 315.27119 - page 14
KICKBACK See Figure 11. I' _ KICKBACK TO LESSEN THE CHANCE OF KICKBACK: • Always keep the correct blade depth setting - the correct blade depth setting for all cuts should not exceed 1/4 in. below the material to be cut. See Figure 13. One blade tooth below the material to be cut works best for most efficient cutting action. BLADE SET TOO DE ...
-
Craftsman 315.27119 - page 15
• When making a cut use steady, even pressure. Never force cuts. • Do not cut warped or wet lumber. • Always hold your saw firmly with both hands andkeep your body in a balanced position so as to resist the . forces of kickback should it occur. When using your saw, always stay alert and exercise control. Do not remove your saw from workpiece ...
-
Craftsman 315.27119 - page 16
TO HELP MAINTAIN CONTROL: • Always support your workpiece near the cut. • Support your workpiece so the cut will be on your left. • Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. Note: The good side is the side on which appearance is important. Before beginning a cut, draw a guideline al ...
-
Craftsman 315.27119 - page 17
TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base as shown in figure 20. TOP VIEWOF SAW BLADE GUIDE NOTCH , , GUIDELINE /- _FRONT OFSAW ALIGN OUTER BLADE GUIDE NOTCH ON SAW BASEWITHLINE OF CUT AS SHOWN WHEN MAKING CROSS CUTS OR RiPCUTS Fig. 20 Since blade thicknesses ...
-
Craftsman 315.27119 - page 18
ALTERNATIVE RIP METHOD See Figure 23. Using C-clamps, firmly clamp a straight edge to the workpeice and guide the saw along the straight edge to achieve a straight rip cut. Do not bind the blade in the cut. ALTERNATIVE METHOD FOR RIP CUTTING WORKPIECE STRAIGHT EDGE Align your line of cut with the inner blade guide notch on the saw base when makin ...
-
Craftsman 315.27119 - page 19
POSITIVE 0 ° BEVEL STOP • Turn screw and adjust base until square with saw See Figure 26. blade. ADJUSTMENT BEVEL ADJUSTMENT KNOB HEX NUT CARPENTER'S BEVELSTOP SQUARE BLADE I Fig. 26 Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0° angle of your saw blade when making 90 ° cuts. However, misalignment can ...
-
Craftsman 315.27119 - page 20
,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil ...
-
Craftsman 315.27119 - page 21
The following recommended accessories are currently available at Sears Retail Stores. • 6-1/2 in. (165 mm) Thin Kerf Blade _. WARNING: The use of attachments or accessories not listed might be hazardous. WARRANTY FULL ONE YEAR WARRANTY ON rRRFTSHRH PROFESSIONAL CORDLESS TRIM SAW If this I:RRFTSMRH Professional Cordless Trim Saw fails due to a def ...
-
Craftsman 315.27119 - page 22
CRAFTSMAN 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW - MODEL NUMBER 315.271190 4 5 6 7 18 _.. 17 8 11 9 10 22 20 19 14 "28 27 9 3O 31 12 13 ...... 22 ...
-
Craftsman 315.27119 - page 23
CRAFTSMAN 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW - MODEL NUMBER 315.271190 I he model number wirr be found on a prate attached to the motor housing. Always mention the model number in all correspondence regarding your I CORDLESS TRIM SAW or when ordering repair parts. J SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key Part No. Number 1 ...
-
Craftsman 315.27119 - page 24
Get it fixed, at your home or ours! For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOM E sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & R ...
У вас вопрос, касающийся Craftsman 315.27119?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Craftsman 315.27119, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Craftsman 315.27119 со всей вероятностью он захочет поделиться методом ее решения.