-
Campbell Hausfeld DG472500DI - page 1
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Operating In ...
-
Campbell Hausfeld DG472500DI - page 2
2. This power tool is intended to function primarily as a cut-off tool or a light-duty angle grinder. Operations such as polishing, wire brushing, and long-duty grinding are not recommended with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury. General Power T ool Safety W arnings R ...
-
Campbell Hausfeld DG472500DI - page 3
3 DG472500DI e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool inunexpected situations. f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices ...
-
Campbell Hausfeld DG472500DI - page 4
4 w) Charge the battery pack in a well-ventilated area. Do not allow any object to cover the charger and/or battery pack while charging. x) Do not operate the charger if it has been dropped, received a sharp blow, or otherwise been damaged. If damaged, have it serviced by a qualified repair person. y) Do not store the battery charger or battery pac ...
-
Campbell Hausfeld DG472500DI - page 5
d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can fly apart. e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or co ...
-
Campbell Hausfeld DG472500DI - page 6
8) Additional Safety Instructions for Grinding and Cutting off Operations a) Always use guard designed for the type of wheel you are using. The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from the broken wheel f ...
-
Campbell Hausfeld DG472500DI - page 7
2) Areas where paint removal is occurring should be sealed with plastic sheeting of at least 4 mils thickness. 3) Sanding should be done in a manner to reduce tracing of paint dust outside the work area. C) CLEANING AND DISPOSAL 1) All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the project. Vacuum ...
-
Campbell Hausfeld DG472500DI - page 8
little or no side-by-side movement when trying to rotate this part on the spindle. If the flange continues to rotate on the spindle, then rotate it until it properly seats itself, that is, until it has little or no side-to-side movement. 4. Inspect the disc to make sure that it is rated for at least 7000 RPM and that it is not broken, cracked, chip ...
-
Campbell Hausfeld DG472500DI - page 9
• Once a cut is started and a notch has formed, continue cutting at the same angle until the desired cut is made. Changing the angle of the disc will cause the wheel to bend and possibly break. • Once the cutting operation is complete, remove the tool from the workpiece and allow the tool to stop rotating before laying it down. Grinding Operati ...
-
Campbell Hausfeld DG472500DI - page 10
• In order to get the most out of your battery pack, it is highly recommended that the packs not remain in the charger for more than 3 hours. So once fully-charged (indicated by the green charger light illuminating), it is best to remove the battery pack at or near that point. • Do not use an extension cord with the charger unless absolutely ne ...
-
Campbell Hausfeld DG472500DI - page 11
11 DG472500DI Notes 26 Sp Manual de Instrucciones 2. Esta herramienta eléctrica está diseñada para funcionar principalmente como una herramienta de corte o una rectificadora de ángulo para trabajos livianos. No se recomienda el uso de esta herramienta eléctrica para trabajos largos de rectificación o brillo. El uso de la herramienta en trabaj ...
-
Campbell Hausfeld DG472500DI - page 12
Limited W arranty 1. DURATION: One (1) Year from the date of purchase by the original purchaser on drill. Batteries are warranted for one (1) year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 424-8936 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The or ...
-
Campbell Hausfeld DG472500DI - page 13
24 Fr Garantie Limitée 1. DURÉE : Un (1) an à partir de la date d’achat par l’acheteur original de l’outil. Les batteries sont garanties pour un (1) an. 2. GARANTIE ACCORDÉE PAR (GARANT) : Campbell Hausfeld/Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Téléphone: (800) 424-8936. 3. BÉNÉFICIAIRE DE CETTE GARANTIE ( ...
-
Campbell Hausfeld DG472500DI - page 14
Pour Pièces de Rechange ou assistance technique, appeler 1-800-424-8936 S’il vous plaît fournir l’information suivante: - Numéro de Modèle - Numéro de série (si présent) - Description et numéro de la pièce N o de Description Pièce Adresser toute correspondance à Campbell Hausfeld Attn: Parts Department 100 Production Drive Harrison, ...
-
Campbell Hausfeld DG472500DI - page 15
22 Fr Instructions D’Utilisation la première fois, charger entièrement la batterie. Ceci s’accomplit en branchant d’abord le chargeur de batterie dans une source de courant de 120 V (60 Hz) et en insérant la batterie complètement dans le chargeur en notant l’orientation de la côte du bloc-batteries pour s’ajuster dans l’encoche du ...
-
Campbell Hausfeld DG472500DI - page 16
21 Fr (0,12 po) ou moins et doit donc être fixée avec la partie soulevée de l’écrou face à l’utilisateur. (Voir la figure 5.) • Lorsque l’écrou de serrage est resserré à la main, resserrer cet arrangement en enfonçant le bouton de verrouillage noir de la broche, puis resserrer l’écrou dans le sens horaire avec la clé fournie à ...
-
Campbell Hausfeld DG472500DI - page 17
20 Fr Instructions D’Utilisation Les disques de coupe sont normalement plus minces que les disques de meulage et sont utilisés principalement pour couper à travers les objets d’acier comme les clous, les boulons, les clôtures, les rails, etc. Les meules de meulage sont normalement plus épaisses et servent pour les applications comme l’éb ...
-
Campbell Hausfeld DG472500DI - page 18
19 Fr e) Supporter les panneaux ou toute pièce de travail surdimensionnée pour réduire le risque de pincement de la meule et de recul. Les larges pièces de travail tendent à s’affaisser sous leurs propres poids. Des supports doivent être placés sous la pièce de travail près de la ligne de coupe et près du bord de la pièce des deux côt ...
У вас вопрос, касающийся Campbell Hausfeld DG472500DI?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Campbell Hausfeld DG472500DI, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Campbell Hausfeld DG472500DI со всей вероятностью он захочет поделиться методом ее решения.