-
Audiovox PRO-9556 - page 1
128-7770 1 of 20 The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be selected to operate from the v ...
-
Audiovox PRO-9556 - page 2
128-7770 2 of 20 T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable Features First Press and release the valet switch 1 ...
-
Audiovox PRO-9556 - page 3
128-7770 3 of 20 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output Not Available 2nd RF S t art Chirp Not Available 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins 4th ...
-
Audiovox PRO-9556 - page 4
128-7770 4 of 20 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time 1 chirp = defrost output pu ...
-
Audiovox PRO-9556 - page 5
128-7770 5 of 20 This Remote S tart/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when th ...
-
Audiovox PRO-9556 - page 6
128-7770 6 of 20 6 THE RECEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboard for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. S pecial considerations must be made for windshield glass as some newer ve ...
-
Audiovox PRO-9556 - page 7
128-7770 7 of 20 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switc ...
-
Audiovox PRO-9556 - page 8
128-7770 8 of 20 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or ...
-
Audiovox PRO-9556 - page 9
128-7770 9 of 20 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...
-
Audiovox PRO-9556 - page 10
128-7770 10 of 20 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote S tart activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue W ire to terminal #86 of a external relay . Connect terminal #85 of the relay to ...
-
Audiovox PRO-9556 - page 11
128-7770 11 of 20 T achometer Input Wiring Det ail 11 Green/Y ellow Wire: Diesel W ait T o S tart Input The Green/Yellow wire of the 2 pin connector will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by ...
-
Audiovox PRO-9556 - page 12
128-7770 12 of 20 The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability of 300mA. Many vehicles today have factory door lock relays which can be connected directly to these outputs, however ...
-
Audiovox PRO-9556 - page 13
128-7770 13 of 20 13 nience, the AS 9159a Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. 2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the ...
-
Audiovox PRO-9556 - page 14
128-7770 14 of 20 14 cylinder , four coil systems, connect to any of the three coils. 3. Connect the Y ellow wire to a +12 volt ignition 1 source. This wire will have +12 volt s with the ignition in the on and start position and have 0 volts with the ignition in the off position. 4. Connect the Green wire to the tach input of the Audiovox remote st ...
-
Audiovox PRO-9556 - page 15
128-7770 15 of 20 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. T emporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch. 4. Sitting in the vehicle, start the engine using the vehicle's ignition key . 5. Step on the brake pedal and shift the gear selector ...
-
Audiovox PRO-9556 - page 16
128-7770 16 of 20 KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from start ...
-
Audiovox PRO-9556 - page 17
128-7770 17 of 20 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition ...
-
Audiovox PRO-9556 - page 18
128-7770 18 of 20 COMPLETING THE INST ALLA TION: After you have confirmed the operation of the Audiovox Remote S tart unit and tested all the safety features of the system: 1. If you have not done so already , place the red rubber handle cover over the handle of the control switch for ease of identification. This will allow your customer to disting ...
-
Audiovox PRO-9556 - page 19
128-7770 19 of 20 © 2006 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7770 ...
У вас вопрос, касающийся Audiovox PRO-9556?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Audiovox PRO-9556, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Audiovox PRO-9556 со всей вероятностью он захочет поделиться методом ее решения.