-
Pelco CM9740-UPG-8312 - page 1
System 974 0 ™ Soft ware Upgrade ® INST ALLA TION MANUAL C1547M (7/03) CM9740-UPG-8312 ...
-
Pelco CM9740-UPG-8312 - page 2
...
-
Pelco CM9740-UPG-8312 - page 3
CONTENTS Section Page INTRODUCTION .................................................................................................................................................................................................................. 1 SOFTW ARE UPGRADE OVERVIEW ........................................................................... ...
-
Pelco CM9740-UPG-8312 - page 4
...
-
Pelco CM9740-UPG-8312 - page 5
C1547M (7/03) 1 INTRODUCTION The CM9740-UPG-8312 software upgrade kit provides the following items to upgrade System 9740 ™ software: 1 System 9740 Setup Disk, version 3.74 1 System 9740 Operation Disk, version 8.03.012 1 System 9740 Utility Disk, version 8.03.012 1 CM9740/9760 Resource CD-ROM, version 8.03.012 2 U12 PROM (programmable read-only ...
-
Pelco CM9740-UPG-8312 - page 6
2 C1547M (7/03) SOFTWARE UPGRADE OVERVIEW Upgrading System 9740 software to version 8.03.012 involves upgrading CM9740-CC1 software and System Manager software. For proper operation of a 9740 system, however , additional components—such as CM9740-MXB and CM9760-KBD/ CM9760-KBR firmware—must also be upgraded. The following list summarizes the va ...
-
Pelco CM9740-UPG-8312 - page 7
C1547M (7/03) 3 UPGRADING SYSTEM 9740 SOFTW ARE IN A SINGLE-NODE SYSTEM NOTE: Any external computer interface (such as an access control system, alarm system, fire system, building management/ control system, or VMX200) that is using the P protocol to communicate with a CM9740-CC1 running version 7.8 or lower soft- ware is not compatible with versi ...
-
Pelco CM9740-UPG-8312 - page 8
4 C1547M (7/03) b. Remove the current System Manager program: (1) In the Windows taskbar , click the Start button. (2) Highlight Settings and then click Control Panel . (3) Double-click the Add/Remove Programs icon. (4) For a PC running Windows 95/98/NT : On the Install/Uninstall tab, click the System Manager 9760 program and then click the Add/Rem ...
-
Pelco CM9740-UPG-8312 - page 9
C1547M (7/03) 5 9. Upgrade the CC1 system software executable file, CM9740.EXE: a. Insert the System 9740 Operation Disk, V ersion 8.03.012, into the disk drive of the CC1. b. Copy the CM9740.EXE executable file from the 9740 directory on the Operation Disk to the C:9740 directory of the CC1. At the C:9740 prompt, enter: copy a:9740cm9740.exe 1 ...
-
Pelco CM9740-UPG-8312 - page 10
6 C1547M (7/03) UPGRADING SYSTEM 9740 SOFTW ARE IN A MUL TI-NODE SYSTEM NOTE: Any external computer interface (such as an access control system, alarm system, fire system, building management/ control system, or VMX200) that is using the P protocol to communicate with a CM9740-CC1 running version 7.8 or lower software is not compatible with version ...
-
Pelco CM9740-UPG-8312 - page 11
C1547M (7/03) 7 b. Remove the current System Manager program: (1) In the Windows taskbar , click the Start button. (2) Highlight Settings and then click Control Panel . (3) Double-click the Add/Remove Programs icon. (4) For a PC running Windows 95/98/NT : On the Install/Uninstall tab, click the System Manager 9760 program and then click the Add/Rem ...
-
Pelco CM9740-UPG-8312 - page 12
8 C1547M (7/03) 6. Upgrade the CC1 system software executable file, CM9740.EXE: a. Insert the System 9740 Operation Disk, V ersion 8.03.012, into the disk drive of the CC1. b. Copy the CM9740.EXE executable file from the 9740 directory on the Operation Disk to the C:9740 directory of the CC1. At the C:9740 prompt, enter: copy a:9740cm9740.exe 7 ...
-
Pelco CM9740-UPG-8312 - page 13
C1547M (7/03) 9 (b) V erify that the 9760NIU.EXE or NET9760.EXE file was renamed to 9760NIU.OLD or NET9760.OLD, respectively , by entering: dir/w (2) Insert the System 9760 Network Disk, version 8.03.012, into the disk drive of the NW1. (3) Copy the executable file, 9760NIU.EXE, from the Network Disk to the C:NETWORK directory on the hard drive of ...
-
Pelco CM9740-UPG-8312 - page 14
10 C1547M (7/03) APPENDIX A. UPGRADING CM9740-MXB FIRMW ARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the proce- dure below . Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components. Handle circuit boards by their edges. ...
-
Pelco CM9740-UPG-8312 - page 15
C1547M (7/03) 11 U5 U11 U12 PROM CHIP U12 U10 ALIGNMENT NOTCH U5 U11 U10 RAM CHIP U10 U12 Figure 3. U12 PROM Chip Figure 4. U10 RAM Chip 3. Replace the existing U12 PROM chip on the video output card with the chip supplied in the upgrade kit: a. Locate the existing U12 PROM chip on the video output card (refer to Figure 3). b. Using the provided ex ...
-
Pelco CM9740-UPG-8312 - page 16
12 C1547M (7/03) 5. Reinstall the video output card into slot 17 of the matrix bay (refer to Figure 2): a. Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay . b. Slide the card toward the rear of the matrix bay until the card is seated firmly with the connectors on the backplane and with the associated ...
-
Pelco CM9740-UPG-8312 - page 17
C1547M (7/03) 13 APPENDIX B. CONNECTING AN ASCII COMMUNICA TIONS DEVICE TO THE CM9740-CC1 As stated previously in this manual, version 8.03.012 of CM9740-CC1 software is not compatible with version 3.20 or earlier of CM9760-DT/CM9760-DT4 software. If you wish to replace the existing DT/DT4 device (external DT) in your system with the use of the int ...
-
Pelco CM9740-UPG-8312 - page 18
14 C1547M (7/03) CONNECTING AN ACD DB9 PORT TO A CM9740-CC1 RJ-45 PORT To connect an ACD DB9 port to a CM9740-CC1 RJ-45 port, refer to Figure 6 and do the following: 1. Connect the 9-pin side of the PV130 converter to a DB9 port of the ACD. 2. If necessary , connect a +12 VDC power supply to the PV130 converter; otherwise, proceed to step 3. (The p ...
-
Pelco CM9740-UPG-8312 - page 19
C1547M (7/03) 15 W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/ MC3 ...
-
Pelco CM9740-UPG-8312 - page 20
World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada ® ...
У вас вопрос, касающийся Pelco CM9740-UPG-8312?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Pelco CM9740-UPG-8312, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Pelco CM9740-UPG-8312 со всей вероятностью он захочет поделиться методом ее решения.