Русский dropdown-ico

Инструкция обслуживания Husqvarna 326EX

24 страниц 0.93 mb
Скачать

Перейти на страницу of 24

Summary
  • Husqvarna 326EX - page 1

    326E X-SERIES Operator’ s manual (CARB II, EP A II) 114 00 19-93 Read through the Operator‘s manual carefully and understand the content before using the machine. ...

  • Husqvarna 326EX - page 2

    2 – English Symbols • Warning! The blade continues to rotate even after the engine has stopped. When the engine has stopped, stop the blade from rotating by letting the blade come in contact with the ground. Indicates the direction of rotation. SYMBOL EXPLANA TION WARNING! The edger can be dangerous! Careless or incorrect use can result in seri ...

  • Husqvarna 326EX - page 3

    English – 3 List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS Personal protective equipment ............................................ 4 The machine‘s ...

  • Husqvarna 326EX - page 4

    4 – English The machine ‘ s safety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance are carried out to ensure that it operates correctly. (See the chapter “ What is what “ to locate where this equipment is positioned on your machine.) Personal protective equipment 3. Cutting at ...

  • Husqvarna 326EX - page 5

    English – 5 6. Cutting equipment The blade is designed and machined for coping with the wear that cutting the edges of lawns involves. 7. Locking nut The locking nut secures the cutting equipment on the output shaft. 5. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from t ...

  • Husqvarna 326EX - page 6

    6 – English 3. Cutting attachment guard • Ensure that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . Control, maintenance and service of the machine ‘ s safety equipment IMPORTANT IN ...

  • Husqvarna 326EX - page 7

    English – 7 Two basic rules: 1) Only use the cutting and guard equipment we recommend! See chapter “ Technical data “ . 2) Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced. 7. Locking nut • Protect your hand from injury when assembling, use the blade guard as protec ...

  • Husqvarna 326EX - page 8

    8 – English Safety instructions before starting work • Inspect the working area. Remove loose objects such as stones, broken glass, nails, steel wire, string, etc. that can be thrown or become entangled in the blade or blade guard. • Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be outside the safety ...

  • Husqvarna 326EX - page 9

    English – 9 Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and transporting fuel approved containers intended for t ...

  • Husqvarna 326EX - page 10

    10 – English Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutting equipment. • NOTE! Never use a machine without t ...

  • Husqvarna 326EX - page 11

    English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children. • Only use origina ...

  • Husqvarna 326EX - page 12

    English – 12 WHA T IS WHA T? What is what on the edger? 1. Blade 2. Grease filler cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air filter cover 16. Clutch cover 17. Handlebar adjustment 18. Locking nut ...

  • Husqvarna 326EX - page 13

    English – 13 Assembling the blade Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fits in the hole of the blade is facing outward. 2. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in the corresponding hole in the drive disc. 3. Fit the blade ...

  • Husqvarna 326EX - page 14

    English – 14 NOTE! The edger is fitted with two-stroke engines and must always be run on a mixture of gasoline and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately. When mixing small amounts of fuel small discrepancies in the amount of oil has a great bearing on the proportions of ...

  • Husqvarna 326EX - page 15

    English – 15 Control before starting WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. ST ART AND ST OP For reasons of safety follow these recommendations! • Check that the support flange is not cracked due to fatigue or due to being t ...

  • Husqvarna 326EX - page 16

    English – 16 Fine adjustment • When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the airfilter should be clean and the airfilter cover fi ...

  • Husqvarna 326EX - page 17

    English – 17 Correctly adjusted carburetor A correctly adjusted carbur etor means that the machine accelerates without hesitation and the machine 4-cycles a little at max speed. F urthermor e, the cutting attachment must not rotate/mo ve at idling. A too lean adjusted low speed needle L may cause starting difficulties and bad acceleration. A too ...

  • Husqvarna 326EX - page 18

    English – 18 A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways. • Aldehydes. The most common formaldehyde, is carcinogenic and causes ...

  • Husqvarna 326EX - page 19

    English – 19 Lubricating the flexible drive axle Adjusting the edger ‘ s cutting depth MAINTENANCE Inside the edger ‘ s drive shaft is a flexible drive axle. The flexible drive axle should be regularly lubricated after 30 hours of operation. Loosen the two screws on the angle gear and remove it. The flexible drive axle is easily removed from ...

  • Husqvarna 326EX - page 20

    English – 20 NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA. Maintenance schedule Below you will fin ...

  • Husqvarna 326EX - page 21

    English – 21 TECHNICAL D A T A T echnical data Engine Cylinder capacity, cu. in/cm 3 Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output axle, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition sy ...

  • Husqvarna 326EX - page 22

    English – 22 FEDERAL AND CALIFORNIA EMISSION CONTR OL W ARRANTY ST A TEMENT ´+H!•¶3l¨ WHAT IS COVERED REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights an ...

  • Husqvarna 326EX - page 23

    English – 23 ...

  • Husqvarna 326EX - page 24

    ´+H!•¶3l¨ 2001W22 ...

Производитель Husqvarna Категория Trimmer

Документы, которые мы получаем от производителя устройства Husqvarna 326EX мы можем разделить на несколько групп. Это в частности:
- технические чертежи Husqvarna
- инструкции обслуживания 326EX
- паспорта изделия Husqvarna
- информационные брошюры
- энергетические этикетки Husqvarna 326EX
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Husqvarna 326EX.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Husqvarna 326EX, инструкции обслуживания, короткие инструкции или инструкции пользователя Husqvarna 326EX. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Husqvarna 326EX.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Husqvarna 326EX, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Husqvarna 326EX пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Husqvarna 326EX.

Полная инструкция обслуживания Husqvarna, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Husqvarna 326EX - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Husqvarna 326EX, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Husqvarna 326EX, которое найдем в данном документе
3. Советы по использованию основных функций устройства Husqvarna 326EX - которые должны облегчить нам первые шаги во время использования Husqvarna 326EX
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Husqvarna 326EX
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Husqvarna 326EX в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Husqvarna 326EX?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Husqvarna 326EX, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Husqvarna 326EX со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)