-
Multitech ISI9234HPCIE - page 1
MultiModem ® ISI ISI9234HPCIE Server Card User Guide ...
-
Multitech ISI9234HPCIE - page 2
MULTIMODEM® ISI SERVER CARD USER GUIDE MultiModem ® ISI Server Card User Guide Model: ISI9234HPCIE Part Number: S000581, Version 1.1.3 Copyright This publication may not be reproduced, in whole or in part, without the specific and express prior written permission signed by an executive officer of Multi-Tech Systems, Inc. All rights reserved. Copy ...
-
Multitech ISI9234HPCIE - page 3
CONTENTS Contents Product Overview .................................................................................................................................................... 5 Product Overview.................................................................................................................................................... ...
-
Multitech ISI9234HPCIE - page 4
CONTENTS Environmental Information .................................................................................................................................... 24 Waste Electrical and Electronic Equipment Statement .............................................................................................. 24 WEEE Directive .............. ...
-
Multitech ISI9234HPCIE - page 5
PRODUCT OVERVIEW Product Overview Product Overview The MultiModem ISI server cards and modems provide four built-in V.92/56K modems on an industry-standard PCI Express x1 architecture for analog dial-up or dedicated fax servers. It also offers V.34/33.6K Super G3 fax and Error Correction Mode to reduce fax transmission time. ISI Server Cards The IS ...
-
Multitech ISI9234HPCIE - page 6
PRODUCT OVERVIEW Documentation Download documentation from www.multitech.com/setup/product.go. MultiModem ISI ISI9234HPCIE User Guide This document. Provides specifications, safety and regulatory information, installation, and configuration information (part number S000581). MultiModem and SocketModem MT9234 AT Provides AT commands for configuring ...
-
Multitech ISI9234HPCIE - page 7
PRODUCT OVERVIEW Specifications Category Description General Bus Type PCI Express form factor 1x, PCIe 1.0 compatible. Interrupt Request One IRQ per card (can be shared) Speed Baud Rates 300 bps to 230 Kbps per port Physical Description Weight 0.45 lbs. (200 g) Dimensions See the topic, Dimensions. Connectors and Cables Connectors One RJ-45 jack Ca ...
-
Multitech ISI9234HPCIE - page 8
PRODUCT OVERVIEW Dimensions Dimensions with Standard Bracket 8 MultiModem ® ISI ISI9234HPCIE Server Card User Guide ...
-
Multitech ISI9234HPCIE - page 9
PRODUCT OVERVIEW Dimensions with Low Profile Bracket Power Measurements Sleep Typical Maximum Peak Total Inrush Total Inrush Charge Charge measured in Duration Millicoulombs during (mC) Powerup 3.3 volts Current (AMPS) 0.402 0.541 0.550 0.592 16.00 26mS Watts 1.320 1.760 1.790 MultiModem ® ISI ISI9234HPCIE Server Card User Guide 9 ...
-
Multitech ISI9234HPCIE - page 10
SAFETY NOTICES Safety Notices Analog Telecom Safety Warnings Before servicing, disconnect this product from its power source and telephone network. Also: ■ Never install telephone wiring during a lightning storm. ■ Never install a telephone jack in wet locations unless the jack is specifically designed for wet locations. ■ Use this product wi ...
-
Multitech ISI9234HPCIE - page 11
INSTALLING HARDWARE Installing Hardware Changing Mounting Brackets To use the low profile bracket, remove the standard bracket and replace it with the low profile bracket. Warning: Before handling the device, discharge any static in your body by touching a piece of grounded metal such as the computer chassis. Electrostatic discharge (ESD) is the re ...
-
Multitech ISI9234HPCIE - page 12
INSTALLING HARDWARE 2. Remove the two screws holding the standard bracket to the device. 12 MultiModem ® ISI ISI9234HPCIE Server Card User Guide ...
-
Multitech ISI9234HPCIE - page 13
INSTALLING HARDWARE 3. Mount the low profile bracket using the screws you removed in Step 1. Installing Hardware Note: Install the hardware, before installing drivers. Warning: Before handling the device, discharge any static in your body by touching a piece of grounded metal such as the computer chassis. Electrostatic discharge (ESD) is the releas ...
-
Multitech ISI9234HPCIE - page 14
INSTALLING HARDWARE Attention: Perform the procedure described in this section only at an ESD workstation using an antistatic wrist strap. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal ground screw (lug). To install the ISI card in your PCI-bus computer: 1. T ...
-
Multitech ISI9234HPCIE - page 15
INSTALLING HARDWARE Cable Diagrams The ISI9234HPCIE uses a single fan-out cable to connect the four modems to four phone lines. The cable has an RJ- 45 connector on one end and four RJ-11 connectors on the other end. Use the RJ-11 connectors to connect to phone lines. MultiModem ® ISI ISI9234HPCIE Server Card User Guide 15 ...
-
Multitech ISI9234HPCIE - page 16
INSTALLING ON WINDOWS Installing on Windows The ISI9234HPCIE supports both 32-bit and 64-bit versions of the following Windows operating systems: ■ Windows Server 2003, 2008, and 2012 ■ Windows 7, 8, Vista, and XP For Linux support, refer to Installing on Linux. Downloading Windows Drivers Note: Drivers for all supported Windows operating syste ...
-
Multitech ISI9234HPCIE - page 17
INSTALLING ON WINDOWS To get the Communications port numbers to match COM ports: 1. In the Device Manager, go to Modems . 2. Right-click MultiTech Systems MT9234SMI #4 and select Uninstall . 3. On the Confirm Device Uninstall tab, check Delete the driver software for this device. ,if provided, and select OK . 4. Repeat the uninstall for the remaini ...
-
Multitech ISI9234HPCIE - page 18
INSTALLING ON LINUX Installing on Linux Installing on Linux Kernel 3.5 and Higher Note: The steps below were tested with Ubuntu 12.04 with Linux kernel 3.5.0 and may or may not work for other 3.x.x versions. After installing the ISI9234HPCIE in a PCIe slot: 1. Power up the computer and boot to Linux. 2. Go to www.multitech.com/setup/product.go and ...
-
Multitech ISI9234HPCIE - page 19
INSTALLING ON LINUX 11. Run the command depmod . 12. Reboot Linux. Linux device drivers and device should now be installed and activated. To verify that the modules loaded, send the command lsmod MultiModem ® ISI ISI9234HPCIE Server Card User Guide 19 ...
-
Multitech ISI9234HPCIE - page 20
CONFIGURING MODEMS FOR YOUR COUNTRY Configuring Modems for Your Country Different countries have different regulations for modem operation. Before using your modems, you must configure them for the country in which you are using them. For Windows computers, use the Global Wizard to set the country. For Linux computers, use AT Commands to set the co ...
-
Multitech ISI9234HPCIE - page 21
CONFIGURING MODEMS FOR YOUR COUNTRY Using AT Commands to Set Country If not using Windows, use AT commands to configure the modem. A complete list of country and region codes is available on the Multi-Tech site at www.multitech.com/global/configuration.go. 1. Run a communication program and open a terminal window. 2. Type AT%T19,0,nn , where nn is ...
-
Multitech ISI9234HPCIE - page 22
REGULATORY INFORMATION Regulatory Information 47 CFR Part 68 Telecom 1. This equipment complies with Part 68 of the 47 CFR rules and the requirements adopted by the ACTA. Located on this equipment is a label that contains, among other information, the registration number and Ringer Equivalence Number (REN) for this equipment or a product identifier ...
-
Multitech ISI9234HPCIE - page 23
REGULATORY INFORMATION Trade Name: SocketModem Model Number: MT9234SMI Registration Number: US:AU7MM01BMT9234SMI Ringer Equivalence: 0.1B Modular Jack (USOC): RJ11C or RJ11W (single line) Service Center in USA: Multi-Tech Systems, Inc. 2205 Woodale Drive Mounds View, MN 55112 USA (763)785-3500 (763) 785-9874 (Fax) 47 CFR Part 15 Regulation Class B ...
-
Multitech ISI9234HPCIE - page 24
ENVIRONMENTAL INFORMATION Environmental Information Waste Electrical and Electronic Equipment Statement WEEE Directive The WEEE Directive places an obligation on EU-based manufacturers, distributors, retailers, and importers to take- back electronics products at the end of their useful life. A sister directive, ROHS (Restriction of Hazardous Substa ...
-
Multitech ISI9234HPCIE - page 25
ENVIRONMENTAL INFORMATION REACH Statement Registration of Substances After careful review of the legislation and specifically the definition of an “article” as defined in EC Regulation 1907/2006, Title II, Chapter 1, Article 7.1(a)(b), it is our current view Multi-Tech Systems, Inc. products would be considered as “articles”. In light of th ...
-
Multitech ISI9234HPCIE - page 26
ENVIRONMENTAL INFORMATION Restriction of the Use of Hazardous Substances (RoHS) Multi-Tech Systems, Inc Certificate of Compliance 2011/65/EU Multi-Tech Systems confirms that its embedded products comply with the chemical concentration limitations set forth in the directive 2011/65/EU of the European Parliament (Restriction of the use of certain Haz ...
-
Multitech ISI9234HPCIE - page 27
ENVIRONMENTAL INFORMATION Information on HS/TS Substances According to Chinese Standards In accordance with China's Administrative Measures on the Control of Pollution Caused by Electronic Information Products (EIP) # 39, also known as China RoHS, the following information is provided regarding the names and concentration levels of Toxic Subst ...
-
Multitech ISI9234HPCIE - page 28
ENVIRONMENTAL INFORMATION Information on HS/TS Substances According to Chinese Standards (in Chinese) 依 依照 照中 中 国 国标 标准 准 的 的有 有毒 毒 有 有害 害物 物 质 质信 信息 息 根据中华人民共和国信息产业部 (MII) 制定的电子信息产品 (EIP) 标准－中华人民共和国《电子信息产品污? ...
У вас вопрос, касающийся Multitech ISI9234HPCIE?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Multitech ISI9234HPCIE, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Multitech ISI9234HPCIE со всей вероятностью он захочет поделиться методом ее решения.