-
Patton electronics 2155 - page 1
USER MANUAL MODEL 2155 CopperLink Ethernet Extender SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2155 Doc# 032111U Rev . A Re vised 2/12/03 An ISO-9001Cer tified Company ...
-
Patton electronics 2155 - page 2
2 CONTENTS 1.0 Warranty Information ................................................................. 3 1.1 Radio and TV Interference ............................................................ 3 1.2 CE Notice ...................................................................................... 3 1.3 Service ...................................... ...
-
Patton electronics 2155 - page 3
3 1.0 W ARRANTY INFORMATION P atton Electronics warr ants all Model 2155 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of the shipment. This warr anty is limited to def ects in workmanship or mater ials, and does not cov er customer damage, ab use o ...
-
Patton electronics 2155 - page 4
4 1.3 SERVICE All warr anty and non-warranty repairs m ust be retur ned freight prepaid and insured to P atton Electronics. All returns must hav e a Retur n Materi- als A uthorization number on the outside of the shipping container . This number ma y be obtained from P atton Electronics T echnical Ser vices at: • T el.: +1 (301) 975-1007 • Emai ...
-
Patton electronics 2155 - page 5
5 2.0 GENERAL INFORMATION Thank you purchasing this P atton Electronics product. This product has been thoroughly inspected and tested and is warr anted f or one year f or par ts and labor . If questions arise while installing or using this product, contact CopperLink T echnical Support at +1 (301) 975-1007 . 2.1 FEATUR ES • Easy-to-install Ether ...
-
Patton electronics 2155 - page 6
6 Figure 1. T ypical application The 2155/L and 2155/R work together to create a transparent e xtension between two peered Ethernet LANs. Figure 1 shows a typical point-to- point application. ...
-
Patton electronics 2155 - page 7
7 3.0 INSTALLATION Because the CopperLink Ether net Extender requires no configuration, it can be installed quickly . Installation consists of the f ollo wing: • Connect the line interf ace between the units (ref er to section 3.1, “Connecting the T wisted-P air Line Interface” on page 7) Note See Figure 2 f or the rear-panel connectors loca ...
-
Patton electronics 2155 - page 8
8 1. T o function properly , two Ethernet Extenders must be connected together using twisted-pair , unconditioned, dr y , metal wire, between 19 (0.9mm) and 26 A WG (0.4mm). Leased circuits that run through signal equalization equipment are not acceptable . 2. The Models 2155 are equipped with an RJ-45 interf ace . The Copper- Link interf aces are ...
-
Patton electronics 2155 - page 9
9 cable . Figure 5 shows how to construct a cable to connect the 10Base-T interf ace to a 10Base-T Hub . Figure 5. Connecting the 10Base-T interf ace to a 10Base-T Hub 3.4 CONNECTING POWER An e xter nal A C or DC power supply is a vailab le separately . This connec- tion is made via the barrel jack on the rear panel of the Model 2155. No configura ...
-
Patton electronics 2155 - page 10
10 External 48 VDC power suppl y • Input – Rated voltage: 36–60 VDC – Rated current: 0.25 A DC at nominal 48 VDC – 3-pin locking connector , 3.5 mm pitch – Reverse polarity protection – T ransient over -voltage pr otection, 100 VDC at 2 ms • Output – Rated voltage: 5 VDC ± 5%, 5W – Rated current; 1 A DC – 6-inch cable termina ...
-
Patton electronics 2155 - page 11
11 4.0 OPERATION Once the CopperLink Ether net Extenders are properly installed, they should operate transparently . No user settings required. This section describes reading the LED status monitors. 4.1 FR ONT PANEL LED STATUS MONITORS The Model 2155 f eatures six front-panel LEDs that monitor connections on the DSL and 10Base-T links, signaling, ...
-
Patton electronics 2155 - page 12
12 T able 1: LED status monitor indications LED Description DSL Link (Activ e Green) Solid green (On) indicates that the end to end DSL F ramer Link is up , signifying that the link across the DSL span is activ e. The DSL Link LED is Off when the link is down. Status Blinks yello w from one to ele ven times to indicate system status. Each pulse pat ...
-
Patton electronics 2155 - page 13
13 4.2 T EST MODES The Model 2155 has a built-in proprietar y loopbac k test mode, plus a built-in V .52 BER test patter n generator , f or ev aluating the communica- tion link. These tests can be activ ated from the front panel of the Model 2155 Ether net Extenders . Remote Digital Loopback (RDL)/V .52 (BER) The Remote Digital Loopback (RDL) test ...
-
Patton electronics 2155 - page 14
14 APPENDIX A SPECIFICATIONS A.1 GENERAL CHARACTERISTICS • Compact low cost plug-and-pla y router • 10Base-T Ether net • Unlimited host suppor t • Six front panel LEDs indicate DSL & 10BT Link, No Signal, Error , and test modes status • Conv enient and standard RJ connectors f or Ether net and line • Exter nal UI A C or 48 VDC power ...
-
Patton electronics 2155 - page 15
15 A.7 CONNECTORS RJ-45 on line side; shielded RJ-45 on Ether net por t A.8 POWER SUPPLY Exter nal 100–240 V A C , 50–60 Hz (univ ersal input option), +5 VDC out- put; 48 VDC (optional), 5 watts , +5 VDC output A.9 T EMPERATUR E RANGE 32–122°F (0–50°C) A.10 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.11 HUMIDITY 5–95% non-condensing ...
-
Patton electronics 2155 - page 16
16 APPENDIX B MODELS 2155 F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES *Only required with optional UI power supply (08055DCUI) P atton Model # Description 2155 Base Models 2155/L CopperLink Ether net Extender ; Line: RJ-11 (Local) 2155/R CopperLink Ether net Extender ; Line: RJ-11 (Remote) 2155-2PK CopperLink Ether net Extender Kit: includes one ...
-
Patton electronics 2155 - page 17
17 APPENDIX C MODELS 2155 INTERF ACE PIN ASSIGNMENT C.1 10BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, & 8: no connection 1 TX+ (data output from 2155) 2 TX- (data output from 2155) 3 RX+ ...
-
Patton electronics 2155 - page 18
18 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ...
-
Patton electronics 2155 - page 19
19 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ...
-
Patton electronics 2155 - page 20
20 Notes ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ...
У вас вопрос, касающийся Patton electronics 2155?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Patton electronics 2155, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Patton electronics 2155 со всей вероятностью он захочет поделиться методом ее решения.