Инструкция обслуживания Murphy PV-101

36 страниц 0.31 mb
Скачать

Перейти на страницу of 36

Summary
  • Murphy PV-101 - page 1

    Rev 09-10-08 00-02-0605 Catalog Section 78 PowerV iew ™ Model PV -101 User ’ s Guide ...

  • Murphy PV-101 - page 2

    In order to consistently bring you the highest qu ality, full featured products, we rese rv e the right to change our specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com. Warranty - A limited warranty on materials and workmanship is given with this FW Murphy produ ct. A copy of the warranty may ...

  • Murphy PV-101 - page 3

    T able of Content s Introduction ............................................................................. 1 Engine and Transmissi on Parameters 2 Faceplate Features 3 Navigation and Keypad Functions 4 Operation ................................................................................. 9 PowerView Menus (First Ti me Start Up) 9 Setting U ...

  • Murphy PV-101 - page 4

    (THIS PAGE INTENTIONALLY LEFT BLANK) ...

  • Murphy PV-101 - page 5

    00-02-0605 - 1 - Rev 09-10-08 Introduction Congratulations on purcha sing your PowerView display, a multifunction tool that provi des a window into the many parameters and service co des of modern electronic engines and transmissions. This guide is intended to help you set up your PowerView display and identify navigation basics and prod uct feat u ...

  • Murphy PV-101 - page 6

    00-02-0605 - 2 - Rev 09-10-08 Engine and Transmi ssion Pa ramete rs The following are some of the engine an d transmission parameters which may be displayed in standard or metric units as well as in English, Spanish, Fre nch, Italian, o r German language s (whe n applicable, consult engine or transmission manufacture r for SAE J1939 supported param ...

  • Murphy PV-101 - page 7

    00-02-0605 - 3 - Rev 09-10-08 Faceplate Features ...

  • Murphy PV-101 - page 8

    00-02-0605 - 4 - Rev 09-10-08 Navigation and Keypad Functions The keypad on the PowerView display is a capa citive touch sensing system. There are no mechani cal switches to wear or stick. When a key is touche d, feedback is provided by the screen flashing. The keys on the keypa d perfo rm the following functions: Menu – Enter or exit menu screen ...

  • Murphy PV-101 - page 9

    00-02-0605 - 5 - Rev 09-10-08 Basic Navigation 1. When Menu is pressed, the main menu items are displayed. ...

  • Murphy PV-101 - page 10

    00-02-0605 - 6 - Rev 09-10-08 2. Touching the Arrow Keys will move the selection bar to other menu items. ...

  • Murphy PV-101 - page 11

    00-02-0605 - 7 - Rev 09-10-08 3. Certain menus have multiple pages of items. Scrolling past the top item or bottom item on the current page will reveal other menu items on addition al pages. ...

  • Murphy PV-101 - page 12

    00-02-0605 - 8 - Rev 09-10-08 4. When the desired item is highlighte d b y the cursor, pressing Enter will select that item and displ ay the corresponding screen. 5. Anytime the word MORE appears above the Arro w Keys there are more screens that may be viewed. Use the Arrow Keys to scroll to the next screen of information. ...

  • Murphy PV-101 - page 13

    00-02-0605 - 9 - Rev 09-10-08 Operation PowerView Me nus ( First T ime Start Up ) 1. When power is first applied to the displa y, the Murphy logo appears. ...

  • Murphy PV-101 - page 14

    00-02-0605 - 10 - Rev 09-10-08 2. If the Engine ECU is broadcasting a 'Wait To Start' message, this screen will be shown. Engine manufacturers typically recommend against starting the engine while this message is bro ad casted from the ECU. Once the ECU stop s bro adcasting this message, this screen will no longer be displayed. ...

  • Murphy PV-101 - page 15

    00-02-0605 - 11 - Rev 09-10-08 3. Once the engine has started, the single engin e parameter appears with the engin e RP M displayed. Pressing the Right Arrow Key will display the coolant temperature. The screen can be changed to other parameters by pressing Menu . ...

  • Murphy PV-101 - page 16

    00-02-0605 - 12 - Rev 09-10-08 Setting Up the Display The screen may be configured to display a single e ngine parameter (1-up display), or four param e ters at once (4-up display). Default options are provide d or you may customize the display by selecting the parameters you wa nt. 1-Up Display Three options are available for modificati on of the ...

  • Murphy PV-101 - page 17

    00-02-0605 - 13 - Rev 09-10-08 1-Up Display Settings 1. Touch Menu and use the Arro w Keys to highlight SETUP 1-UP DISPLAY, then press Enter . 2. To select USE DEFAULTS, highlight the option an d press Enter . A message indicatin g “RESTORED TO DEFAULTS” is displayed. 3. To select CUSTOM SETUP, highlight the option and press Enter . A list of e ...

  • Murphy PV-101 - page 18

    00-02-0605 - 14 - Rev 09-10-08 6. Continue to scroll and select additional para meters for the CUSTOM 1-UP DISPLAY. Touch Menu at any time to return to the CUSTOM SETUP menu. 7. Selecting the AUTOMATI C SCAN ON function will cause the 1-up display to scroll throu gh the sel ected set of parameters one at a time. 8. Once the USE DEFAULTS, CUSTOM SET ...

  • Murphy PV-101 - page 19

    00-02-0605 - 15 - Rev 09-10-08 4-Up Display The 4-up display places the param eter d ata into four areas of the screen known as quadrants. Fa ctory defaults f or the 4-up display include coolant temperatu re, engine speed, oil pressure, and battery voltage. You may customize the 4-up display with parameters you define for each q uad rant. 1. Touch ...

  • Murphy PV-101 - page 20

    00-02-0605 - 16 - Rev 09-10-08 5. Touch Enter and a list of parameters will appear. The parameter that is highlighted is the sele cted parameter for the screen. The number to the right of the parameter indicates the quadrant in wh ich it is displayed. 1 = upper left quadrant 2 = lower left quadrant 3 = upper right quadrant 4 = lower right quadrant ...

  • Murphy PV-101 - page 21

    00-02-0605 - 17 - Rev 09-10-08 8. The parameter in the sele cted qu adrant has changed to the parameter selected in the previo us screen. 9. Repeat the parameter selection process until all spa c es are filled. ...

  • Murphy PV-101 - page 22

    00-02-0605 - 18 - Rev 09-10-08 Main Me nu Optio ns This section describes the feature s listed on the main menu of the PowerView. These menu options are displayed whenever you touch Menu . The Arrow Key s allow you to scroll the items, and Enter selects the highlighted option. Selecting a Language From LANGUAGES, you may select ENGLISH, ESPANOL, FR ...

  • Murphy PV-101 - page 23

    00-02-0605 - 19 - Rev 09-10-08 Backlight Adjustment ADJUST BACKLIGHT allows you to select the desired backlight intensity. Contrast Adjustment From ADJUST CONTRAST, you may select the de sired contrast intensity. Select Units From SELECT UNITS, you may select how information is displayed. ENGLISH for Imperial units, i.e., PSI, ° F or METRIC KPA, M ...

  • Murphy PV-101 - page 24

    00-02-0605 - 20 - Rev 09-10-08 Faults and Warnings The PowerView provides two means for detecting faults and warnings: visual LEDs on the casing (See “Faceplate Features”) and fault indicators on the display. Visual Indication • Amber LED (Warning) • Red LED (Derate / Shutdown) Fault Indicators ...

  • Murphy PV-101 - page 25

    00-02-0605 - 21 - Rev 09-10-08 Auxiliar y Gage Fault Murphy’s PVA Gages can be atta ched to the PowerView. If an auxiliary gage should fail, the 1-up or 4-up displ ay will be replaced with the fault message “GAGE NOT RESPONDING”. NOTE : The fault can only be cleared by correcting the cause of the fault condition. Active Fault C odes When the ...

  • Murphy PV-101 - page 26

    00-02-0605 - 22 - Rev 09-10-08 Acknowledging Fault Codes 1. To acknowledge and hide the fault and return to the 1-up or 4-up display, touch Enter . The display will return to the 1-up or 4-up display, but the display will contain the shutdown icon. 2. Touch Enter to redisplay the hidden fault. Touch Enter once again will hide the fault and return t ...

  • Murphy PV-101 - page 27

    00-02-0605 - 23 - Rev 09-10-08 Utilities Menu The following steps take place starting at the UTILITIES menu option. 1. GAGE DATA - View information for optional connecte d PVA gages. 2. REMOVE ALL GAGES - Reset the PowerView's gage memory. 3. SOFTWARE VERSION - View the PowerView's software version. 4. MODBUS SETUP – refer to ‘Modbus ...

  • Murphy PV-101 - page 28

    00-02-0605 - 24 - Rev 09-10-08 being used. Most engine ECU’ s use Version 4, therefore in most cases adjustment of this menu opti on will not be required. Upon receiving an unrecogniza ble fault, cha nge to a different J1939 Version. If the fault SPN does not change when the version i s changed, the ECU generating the fault is using Fault Conv er ...

  • Murphy PV-101 - page 29

    00-02-0605 - 25 - Rev 09-10-08 Modbus ® Setup 1. From the UTILITIES menu, select MODBUS SETUP. 2. Select either the SLAVE ACTIVE (SCADA or remote Modbus master) or MASTER ACTIVE (a uxiliary gage s) modes. Touch Enter to toggle betwee n master and slave. 3. Select SERIAL PORT SETUP (slave mode only), then touch Enter . 4. Continue to scroll each se ...

  • Murphy PV-101 - page 30

    00-02-0605 - 26 - Rev 09-10-08 Selecting Engine ECU 1. From the UTILITIES menu, choose SELECT ENGINE ECU. 2. The message “LISTEN TO ECU: ALL” is displaye d as the default setting, and indicates the PV101 is listenin g to all devices on the network. 3. To change the setting to a specific address, pres s the Arrow Keys to scroll through the numbe ...

  • Murphy PV-101 - page 31

    00-02-0605 - 27 - Rev 09-10-08 T r oubleshooting “WAIT TO START PREHEATIN G” is displa yed The ECU is broadcasting a 'Wait To Start' message. E ngine manufacturers typically recommend against starting the engine while the ECU is broadca sting th is message. Once the ECU stops broadcasting th is message, this screen will no longer be d ...

  • Murphy PV-101 - page 32

    00-02-0605 - 28 - Rev 09-10-08 “NO STOR ED CODES” is disp layed The PowerView sent a request to the ECU for Stored Fault Code (DM2) information, and the ECU resp onded. There are zero stored codes. “NO GAGE DATA” is displayed The PowerView has no record of gages conn ecte d to the RS485 bus. “NO DATA” is di splay ed in place of a p aram ...

  • Murphy PV-101 - page 33

    00-02-0605 - 29 - Rev 09-10-08 “DATA ERROR” is displ ayed in place of a para meter value The ECU is sending a message that there is a data error with this parameter. Or (PV101 only) FUEL LEVEL has been selected for display, ANALOG INP UT has been set to FUEL LEVEL, but no Murphy Fuel Sender has been connected to the analog input. One of the 4-U ...

  • Murphy PV-101 - page 34

    00-02-0605 - 30 - Rev 09-10-08 NOTES ...

  • Murphy PV-101 - page 35

    Murphy, the Murphy logo, and Po werVie w are registered a nd/or common law trademarks of Murphy Industries, Inc. This document, including textual matter and illustrations, is c opyright protected by Murphy Industries, Inc., with a ll rights reserved. (c) 2008 Murphy Industries, Inc. Other third party product or trade names referenced herein are the ...

  • Murphy PV-101 - page 36

    www.fwmurphy.com/products/murphyl ink/powerview.htm ...

Производитель Murphy Категория GPS Receiver

Документы, которые мы получаем от производителя устройства Murphy PV-101 мы можем разделить на несколько групп. Это в частности:
- технические чертежи Murphy
- инструкции обслуживания PV-101
- паспорта изделия Murphy
- информационные брошюры
- энергетические этикетки Murphy PV-101
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Murphy PV-101.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Murphy PV-101, инструкции обслуживания, короткие инструкции или инструкции пользователя Murphy PV-101. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Murphy PV-101.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Murphy PV-101, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Murphy PV-101 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Murphy PV-101.

Полная инструкция обслуживания Murphy, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Murphy PV-101 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Murphy PV-101, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Murphy PV-101, которое найдем в данном документе
3. Советы по использованию основных функций устройства Murphy PV-101 - которые должны облегчить нам первые шаги во время использования Murphy PV-101
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Murphy PV-101
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Murphy PV-101 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Murphy PV-101?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Murphy PV-101, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Murphy PV-101 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (2)

Andrey

Hello Cattapiller engine C10 - I can connect this device ?, what need for this connect and use ? Regards Andrey

Andrey

Hello Cattapiller engine C10 - I can connect this device ?, what need for this connect and use ? Regards Andrey