-
Pelco c1943m - page 1
CM9760-VCRC-P VCR Contr oller Installation/ Operation Manual C1943M (9/99) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120 ® ...
-
Pelco c1943m - page 2
2 P elco Manual C1943M (9/99) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND W ARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 3 MODELS .......................................................... ...
-
Pelco c1943m - page 3
P elco Manual C1943M (9/99) 3 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser v ed. 1. Installation and servicing should only be done by qualified service personnel and con- form to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X , ...
-
Pelco c1943m - page 4
4 P elco Manual C1943M (9/99) MODELS CM9760-VCRC-P VCR control unit capable of controlling 64 VCRs per unit. VCR control is specific to P elco TLR2096 . OPTIONS CM9760-VCRC-PTX A 50-foot (15.2 m) VCR control cab le with 1/8-inch jack on one end (f or connecting to VCR) and cord/shield (signal/ground) bare wires at the opposite end for connection to ...
-
Pelco c1943m - page 5
P elco Manual C1943M (9/99) 5 DIP SWITCHES With the front panel remov ed, DIP switch 1 and DIP s witch 2 are visible . These two ten-position DIP switches configure and define man y functions of the CM9760-VCRC-P . Figure 3 identifies the relativ e locations of DIP s witches 1 and 2. DIP switch functions are discussed in the Setup section. LEDs The ...
-
Pelco c1943m - page 6
6 P elco Manual C1943M (9/99) REAR VIEW The rear of the unit is illustrated in Figure 4. F rom left to right are the following: 1 . The four 16-input b locks of VCR connectors in the form of screw-type connectors with associated mating plugs (one shown in Block 1) running from the left rear to middle right of the unit 2. The VCRC-P output relay (on ...
-
Pelco c1943m - page 7
P elco Manual C1943M (9/99) 7 INPUT VCR CONNECTORS Physically , each of the four VCRC-P input connectors consists of the same number of input screw-type terminals. Each input group uses a dual-row removable plug and each plug is associated with 8 VCR inputs. For e xample, ref er to the leftmost group represented in Figure 5, which shows VCR inputs ...
-
Pelco c1943m - page 8
8 P elco Manual C1943M (9/99) RELA Y OUTPUT CONNECTOR Figure 6 illustrates the rela y output connector and its relative por t pin assignments . The connector is a three-position plug with screw-type contacts similar in operation to the mat- ing connectors just discussed. By default, the relay is in its normal state at power up of the unit as shown ...
-
Pelco c1943m - page 9
P elco Manual C1943M (9/99) 9 DB-9 Connector Pin-outs The DB-9 connector is reserved for f actor y use only . RJ-45 Connector RJ-45 connector pin-outs are illustrated in Figure 7. Because both RJ-45 connectors have the same wiring pin-outs, they require the same “flipped” cable. In other words, the IN connector requires a “flipped” cable fo ...
-
Pelco c1943m - page 10
10 P elco Manual C1943M (9/99) POWER CONNECTIONS The CM9760-VCRC-P utilizes an auto-ranging internal transf or mer circuit that allows the in- put power to r ange from 100-240 V AC @ 50/60 Hz. Associated with the input pow er is the pow er ON/OFF switch and the input po wer fuse. The fuse is easily changed as illustrated in Figure 9. Figure 9. Powe ...
-
Pelco c1943m - page 11
P elco Manual C1943M (9/99) 11 SETUP PRELIMINAR Y DISCUSSION The CM9760-VCRC-P enables automatic control (via macro e xecution) or man ual control (from the CM9760-KBD) of sev en predefined VCR functions. Each VCRC-P can control up to 64 VCRs. VCR control is implemented by associating System 9760 GPIs to VCRs. When a GPI is used for VCR control, it ...
-
Pelco c1943m - page 12
12 P elco Manual C1943M (9/99) Figure 10. DIP Switch Functions NOTE: POSITIONS 9 AND 10 ARE NOT USED AND SHOULD BE LEFT IN THE F ACT ORY DEF A UL T “OFF” POSITION. ...
-
Pelco c1943m - page 13
P elco Manual C1943M (9/99) 13 SOFTW ARE SETUP–USING THE MGR PROGRAM TO CONFIGURE VCRC-P OPERA TION The VCRC-P unit controls up to 64 VCRs per unit and provides se ven basic functions of VCR control direct from the CM9760 ke yboard. These controls include Stop , Pause , Play , Eject, F ast Forward, Re wind, and Record. The VCRC-P accepts GPI comm ...
-
Pelco c1943m - page 14
14 P elco Manual C1943M (9/99) 7 . This brings up the GPI SETUP file dialog box (.GPI file). Refer to Figure 12. 8. Program logical GPI numbers f or all the physical numbers that will be used. The ph ysi- cal GPI numbers correspond to a specific VCR control signal on the VCR controller . These GPI numbers correspond to the same numerical “Connect ...
-
Pelco c1943m - page 15
P elco Manual C1943M (9/99) 15 Figure 13. Configuring the COMMS file for VCRC-P Operation 10 . Define operator access, sa ve the GPI file, return to the MGR main menu screen and press the tab to bring up the COMMS file (.SCP file). Refer to Figure 13. 1 1 . In the COMMs file assign an equipment number “17” to the port on the CC1 that will be us ...
-
Pelco c1943m - page 16
16 P elco Manual C1943M (9/99) INST ALLA TION Physical installation of the VCRC-P unit is relatively simple, although various configurations are possible. DIRECT RACK-MOUNT HOOK-UP Regardless of the location of a VCRC-P unit, it will more than likely be installed in a rack (refer to Figure 14). The VCRC-P unit mounts in a standard 19-inch (48.26 cm ...
-
Pelco c1943m - page 17
P elco Manual C1943M (9/99) 17 OPERA TIONAL OVERVIEW The basic function of the VCRC-P unit is to act as an interface between the user/operator of the system and any connected VCRs. Each VCRC-P processes and executes only com- mands with addresses that match the controller address. When a VCRC-P receives a com- mand with an inappropriate address it ...
-
Pelco c1943m - page 18
18 P elco Manual C1943M (9/99) OPERA TING THE CM9760-VCRC-P FROM THE CM9760-KBD Direct control operation of VCRs attached to VCRC-Ps from a CM9760-KBD is relatively straightf orward. Once the system is running and the ke yboard is online, direct control of a VCR is as follows: 1. Select an input (camera) that was prog rammed as a VCR on the keyboar ...
-
Pelco c1943m - page 19
P elco Manual C1943M (9/99) 19 SPECIFICA TIONS Electrical Input V oltage: Auto-r anging 100-240 V AC , 50/60 Hz P o wer: Consumption: 30 vA Data P or ts Input: RS-422, RJ-45 connector DIP switch selectable baud rate Output: RS-422, RJ-45 connector . DIP switch selectable baud rate Output: DB-9 connector F actor y use only Indicators: 2 power LEDs , ...
-
Pelco c1943m - page 20
20 P elco Manual C1943M (9/99) P elco, the P elco logo, Camclosure, Esprit, Gene x, Legacy , System 9760, and Spectra are registered trademarks of P elco. © Cop yr ig ht 1999, P elco. Endura and ExSite are trademarks of P elco. All rights reser v ed. REVISION HISTOR Y Manual # Date Comments C1943M 9/99 Original version. REGULA TOR Y NOTICES NO TE: ...
У вас вопрос, касающийся Pelco c1943m?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Pelco c1943m, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Pelco c1943m со всей вероятностью он захочет поделиться методом ее решения.