-
Kustom 36 coupe - page 1
...
-
Kustom 36 coupe - page 2
...
-
Kustom 36 coupe - page 3
T able of Contents Introduction..........................................................................2 Safety Information.................................................................4 Amp Specifications................................................................8 ‘36 Coupe Control Panels............................................... ...
-
Kustom 36 coupe - page 4
Congratulations! 2 Introduction “IS IT REALL Y THA T SIMPLE?” you ask. YES . When an amp has tone this hot, looks this cool and Vibe out the wazoo, it’ s bound to happen. Y ou are now a hipper person than before. Y ou look better , you seem smarter and you’ve probably even become more popular . “ Why? ” you ask. Here’ s the answer ... ...
-
Kustom 36 coupe - page 5
The Coupe is a one-of-a-kind amplifier in a sea of retreads . It has a special look that recaptures the flash of VINT AGE 1960s and ‘70s Kustom amps but with the T one that players often dream about, but don’t often attain. We’re talking about hot , chunky , su st ai ni ng sounds that will remind you why you play guitar in the first place. ...
-
Kustom 36 coupe - page 6
4 Safety Information ...
-
Kustom 36 coupe - page 7
5 Safety Information ...
-
Kustom 36 coupe - page 8
6 Safety Information ...
-
Kustom 36 coupe - page 9
7 Safety Information ...
-
Kustom 36 coupe - page 10
8 Amp Specifications Model 36 Coupe All T ube guitar amp Power Amp T ubes 2-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects loop, 1 phase inverter) Output Power 36 W RMS 16, 8, or 4 Ohms @ 5% THD Speakers 1 X 12 inch KEI(Kustom-Eminence Integrated) with aluminum dust cover Input Impedance ...
-
Kustom 36 coupe - page 11
9 Amp Specifications Model 72 Coupe All T ube guitar amp Power Amp T ubes 4-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects loop, 1 phase inverter) Output Power 72 W RMS 16, 8, or 4 Ohms @ 5% THD Speakers 2 X 12 inch KEI(Kustom-Eminence Integrated) with aluminum dust cover Input Impedance ...
-
Kustom 36 coupe - page 12
10 Amp Specifications Model 72 Coupe Hardtop All T ube guitar amp head Power Amp T ubes 4-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects loop, 1 phase inverter) Output Power 72 W RMS 16, 8, or 4 Ohms @ 5% THD Input Impedance Hum & Noise -85 dBV Residual Noise, all level controls 0% (m ...
-
Kustom 36 coupe - page 13
? ...
-
Kustom 36 coupe - page 14
’36 Coupe Front P anel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound. It can also be useful when us- ing pedals in front of the amp, since it provid ...
-
Kustom 36 coupe - page 15
8) Lead V olume/Pull Bright —The Lead V olume control adjusts the gain at the input of the amplifier when the Lead channel is active. It is used in conjunction with the Lead Master to adjust the amount of distortion and volume for the channel. For cleaner sounds, this control would be set to lower settings and the Master set higher ...for slight ...
-
Kustom 36 coupe - page 16
’36 Coupe Back 1) Footswitch —The Footswitch jack on the Coupe is a stereo jack that connects the Coupe footswitch to the amplifier . It uses a special circuit to decode the three switches through a simple stereo cable. In an emer - gency , a mono instrument cable can be used to allow footswitching of the channels only . In this setup, the LED ...
-
Kustom 36 coupe - page 17
...
-
Kustom 36 coupe - page 18
’72 Coupe Front P anel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound. It can also be useful when us- ing pedals in front of the amp, since it provid ...
-
Kustom 36 coupe - page 19
lower settings and the Master set higher . For slight breakup, the controls would be set in their middle ranges. For heavier distortion, set the Lead V olume higher and the Master lower . Pulling the Pull Bright will increase the high frequencies of the signal, while also reducing low frequencies for a chunkier , tighter attack. This function is ve ...
-
Kustom 36 coupe - page 20
’72 Coupe Back 1) Footswitch Assignment —This button selects which of the amp’ s ef - fects are controlled by the “Effects” button on the footswitch. If the switch is IN, the footswitch will control the Reverb and the T remolo will only be controlled by the Pull Active Switch on the Speed control. If the Footswitch Assignment button is OU ...
-
Kustom 36 coupe - page 21
’72 Coupe Bottom 1) Power Cord Receptacle/Fuse Holder: Insert the AC cord (provided) firmly into the AC connector . NOTE: Replace the AC power cord if protective jacket is damaged or ground pin is damaged or removed. The fuse is located in a housing just below the re- ceptacle. Replace only with same type and size. T o remove the fuse, remove AC ...
-
Kustom 36 coupe - page 22
20 ’72 Coupe Hardtop Fr ont Panel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound. It can also be useful when us- ing pedals in front of the amp, sinc ...
-
Kustom 36 coupe - page 23
21 lower settings and the Master set higher . For slight breakup, the controls would be set in their middle ranges. For heavier distortion, set the Lead V olume higher and the Master lower . Pulling the Pull Bright will increase the high frequencies of the signal, while also reducing low frequencies for a chunkier , tighter attack. This function is ...
-
Kustom 36 coupe - page 24
22 ’72 Coupe Hardtop Back 1) Effects Send —This 1⁄4” jack delivers a tube-driven preamp signal to ex- ternal effects devices. It can be used to send the signal to another amplifier to run multiple amps. Connecting a 1⁄4” plug does NOT break the flow of the amplifier signal. T o connect two Coupe amplifiers in stereo, a stereo effect ...
-
Kustom 36 coupe - page 25
23 9) Impedance Selector —This switch is used to select the appropriate impedance, and is important in achieving the desired results from the Coupe amplifiers. The cor - rect impedance should be selected using the Impedance Selector Switch as follows: Incorrectly “mismatching” the amp to the speaker should not damage the amplifier , but wou ...
-
Kustom 36 coupe - page 26
Coupe Footswitch 1) LEAD —The Lead footswitch selects between Rhythm and Lead Chan- nels on the amplifier , regardless of the setting of the channel selector switch on the front panel. If the LEAD word is backlit, then the Lead chan- nel is active. If the LEAD word is unlit, then the Rhythm channel is ac- tive. 2) BOOST —The Boost ...
-
Kustom 36 coupe - page 27
...
-
Kustom 36 coupe - page 28
Kustom Amplification • Cincinnati, OH, USA • WWW .KUSTOM.COM ...
У вас вопрос, касающийся Kustom 36 coupe?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Kustom 36 coupe, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Kustom 36 coupe со всей вероятностью он захочет поделиться методом ее решения.