Русский dropdown-ico

Инструкция обслуживания NEC NEC MultiSync LCD3210 LCD3210 LCD3210

38 страниц 0.33 mb
Скачать

Перейти на страницу of 38

Summary
  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 1

    (1/38) External Contro l LCD3210 1. Application This document defines the communications method for control of the LCD3210 when using an external controller . 2. Connectors and wiring Connector: D-Sub 9-pin Cable: Cross (reversed) cable or null modem cable 3. Communication Parameter (1) Communication system Asynchronous (2) Interface RS-232C (3) Ba ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 2

    (2/38) 4. Communication Format The command packet consists of four parts, Header, Message, Check code and Delimiter. Sequence of a typical procedure to control a monitor is as follows, [A controller and a monitor, two-way communication composition figure] 4.1 Header block for mat (fixed lengt h) 1 st byte) SOH: Start of Header ASCII SOH (01h) 2 nd ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 3

    (3/38) 4 th byte) Source: Source equipment ID. (Sender) Specify a sender address. The controller must be ‘0’(30h). 5 th byte) Message Type: (Case sensitive.) Refer to section 4.2 “Message block format” for more details. ASCII 'A' (41h): Command ASCII 'B' (42h): Command reply. ASCII 'C' (43h): Get current parame ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 4

    (4/38) 3 ） Set parameter The controller sends this message to change a setting of the monitor. Message format of the “Set parameter” is as follows;  Refer to section 5.3 “Set parameter” for more details. 4 ） Set Parameter reply The monitor replies with this message for a confirmation of the “Set parameter message”. Message format ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 5

    (5/38) Following is an example of a Check code (BCC) calculation. Check code (BCC) D 17 = D 1 xor D 2 xor D 3 xor … xor D 14 xor D 15 xor D 16 = 30h xor 41h xor 30h xor 45h xor 30h xor 41h xor 02h xor 30h xor 30h xor 31h xor 30h xor 30h xor 30h xor 36h xor 34h xor 03h = 7 7 h 4.6 Del imiter Packet delimiter code; ASCII CR(0Dh). Header Message SOH ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 6

    (6/38) 5. Message type 5.1 Get curr ent Paramet er from a monitor . Send this message when you want to get the status of a monitor. For the status that you want to get, specify the “OP code page” the “OP code”, refer to “Appendix A. Operation code table”. 1 st byte) STX: Start of Message ASCII STX (02h) 2 nd -3 rd bytes) OP code page: O ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 7

    (7/38) 00h: No Error. 01h: Unsupported operation with this monitor or unsupported operation under current condition. This result code from the monitor is encoded to ASCII characters. Ex.) The byte data 01h is encoded to ASCII character '0' and '1' (30h and 31h). 4 th –5 th bytes) OP code page: Operation code page. These bytes ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 8

    (8/38) Ex) The byte data 02h must be encoded to ASCII '0' and '2' (30h and 32h). Refer to the Operation code table. 4 th -5 th bytes) OP code: Operation code This OP code data must be encoded to ASCII characters. OP code 1Ah -> OP code (Hi) = ASCII '1' (31h) OP code (Lo) = ASCII 'A' (41h) Refer to the Oper ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 9

    (9/38) ASCII '0''1' (30h, 31h): Momentary Like Auto Setup function, that automatically changes the parameter. 10 th -13 th bytes) Max. value: Maximum value that monitor can accept. (16bits) Reply data from the monitor is encoded to ASCII characters. Ex.) '0''1''2''3' means 0123h (291) 14 t ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 10

    (10/38) Bit 5-2 Reserved (Don't care) Bit 1 1:Positive Horizontal sync polarity. 0:Negative Horizontal sync polarity. Bit 0 1:Positive Vertical sync polarity. 0:Negative Vertical sync polarity.  H Freq: Horizontal Frequency in unit 0.01kHz  V Freq: Vertical Frequency in unit 0.01Hz Ex.) When H Freq is '1''2''A&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 11

    (11/38) Delimiter CR (0Dh): End of packet Step 2. The monitor replies with current Brightness setting and capability to support this operation. Header SOH (01h): Start Of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). 'D&apo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 12

    (12/38) Step 4. The monitor replies with a message for confirmation. Header SOH (01h): Start Of Header '0' (30h): Reserved '0' (30h): Message receiver is the controller 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). 'F' (46h): Message Type is "Set parameter reply" '1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 13

    (13/38) 6.2. How to read the measuremen t value of the built-in temperature sensors. LCD3210 has two built-in temperature sensors. The controller can monitor inside temperatures by using those sensors through RS-232C. The following shows the procedure for reading the temperatures from the sensors. Step 1. Select a temperature sensor which you want ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 14

    (14/38) Delimiter CR (0Dh): End of packet Step 3. The controller requests the monitor to send the temperature from the selected sensor. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'C'-'0'-'6' STX-'0'-'2'-'7'-'9'-ETX BCC CR Header SOH (01h): S ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 15

    (15/38) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 7. Power control procedure 7.1 Power status read 1) The controller requests the monitor to reply a current power status. Header Message Check code Delimiter SOH-'0'-'A&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 16

    (16/38) Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 7.2 Power con trol 1) The controller requests the monitor to control monitor power. Header SOH (01h): Start Of Header '0' (30h): Reserved 'A' (41h): Monitor ID LCD3210 must be ASCII 'A& ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 17

    (17/38) Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet. ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 18

    (18/38) 8. Asset Data read and write 8.1 Asset Data Read Requ est and repl y This command is used in order to read Asset Data. 1) The controller requests the monitor to reply with Asset data. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'A' STX-'C'-'0'-&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 19

    (19/38) 8.2 Asset D ata write This command is used in order to write Asset Data. 1) The controller requests the monitor to write Asset data. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-N-N STX-'C'-'0'-'0'-'E'-'0'-'0'- Data(0)-Data(1)---Da ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 20

    (20/38) 9. Date & Time read and write 9.1 Da te & Ti me Read This command is used in order to read the setting of Date & Time. 1) The controller requests the monitor to reply with the Date & Time. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'6' STX-'C&a ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 21

    (21/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 22

    (22/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 23

    (23/38) WW: weekdays '0'-'0'(30h, 30h): Sunday '0'-'1'(30h, 31h): Monday '0'-'2'(30h, 32h): Tuesday '0'-'3'(30h, 33h): Wednesday '0'-'4'(30h, 34h): Thursday '0'-'5'(30h, 35h): Friday '0'-'6'(30h, 36h): Saturday ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 24

    (24/38) 10.Schedule read and write 10.1 Schedule Read This command is used in order to read the setting of the Schedule. 1) The controller requests the monitor to read Schedule Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'8' STX-'C'-'2'-'1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 25

    (25/38) OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off timer isn't set. OFF_MIN: Turn off time (minute) '0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 (=3Bh) '3'-'C'(3 ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 26

    (26/38) 10.2 Schedule Write This command is used in order to write the setting of the Schedule. 1) The controller requests the monitor to write Schedule . Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'1'-'6' STX-'C'-'2'-'1'-'4'-PG-ON HOURS ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 27

    (27/38) EX. '0'-'1'(30h, 31h): Monday '0'-'4'(30h, 34h): Wednesday '0'-'F'(30h, 46h): Monday, Tuesday, Wednesday and Thursday '7'-'F'(37h, 46h): Monday to Sunday FL: Option bit 0: Everyday bit 1: Every week bit 2: Schedule Disable/Enable * When bit0 and bit1 are '1 ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 28

    (28/38) ON_MIN: Turn on time (minute) '0'-'0'(30h, 30h): 0 | '3'-'B'(33h, 42h): 59 '3'-'C'(33h, 43h): On timer isn’t set. OFF_HOUR: Turn off time (hour) '0'-'0'(30h, 30h): 00 | '1'-'7'(31h, 37h): 23 (=17h) '1'-'8'(31h, 38h): Off ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 29

    (29/38) 3) The controller requests the monitor to write Enable/Disable Schedule. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'A' STX-'C'-'2'-'1'-'5'-PG-EN-ETX BCC CR Header SOH (01h): Start Of Header '0' (30h): Reserved &apo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 30

    (30/38) BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet 11. Self diagnosis 11.1 Self-diagnosi s status rea d This command is used in order to read the Self-diagnosis status. 1) The controller requests the monitor to read Self-diagnosis status. Header Message Check code Delimit ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 31

    (31/38) ETX (03h): End of Message Check code BCC: Block Check Code Refer to the section 4.5 “Check code” for a BCC calculation. Delimiter CR (0Dh): End of packet ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 32

    (32/38) 12. Serial No. & Model Name Read 12.1 Serial No. Read This command is used in order to read a serial No. 1) The controller requests the monitor to read a serial No. Header Message Check code Delimiter SOH-'0'-'A'-'0'-'A'-'0'-'6' STX-'C'-'2'-'1'-&ap ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 33

    (33/38) Header SOH (01h): Start Of Header '0' (30h): Reserved 'A' (41h): Monitor ID LCD3210 must be ASCII 'A' (41h). '0' (30h): Message sender is the controller 'A' (41h): Message type is "Command" '0'-'6'(30h, 36h): Message length. Message STX (02h): Start of Message & ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 34

    (34/38) Appendix A. Operation Code (OP code) Table Item OP code page OP code Parameter Remarks Brightness 00h 10h 0: dark | MAX.: bright Contrast 00h 12h 0: low | MAX.: high Sharpness 00h 8Ch 0: dull | MAX.:sharp Tint 00h 90h 0: | MAX.: Color 02h 1Fh 0: pale | MAX.: deep Black Level 00h 92h 0: dark | MAX.: bright Noise Reduction 02h 20h 0: Off | MA ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 35

    (35/38) Item OP code page OP code Parameter Remarks Zoom V-Position 02h CDh 0: Down side | Max.: Up side Screen reset 00h 06h 1: Reset Momentary Balance 00h 93h O: Left | 50:(Center) | 100: Right Treble 00h 8Fh O: Min. | 50:(Center) | 100: Max. Bass 00h 91h 0: Min. | 50:(Center) | 100: Max. AUDIO Audio reset 02h 31h 1: Reset Momentary PIP Size 02h ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 36

    (36/38) Item OP code page OP code Parameter Remarks VIDEO EQ. 02h E0h 0: | 7: LongCable Manual SYNC Terminate 02h E1h 1:Hi(2.2kohm) 2:Lo(75ohm) OSM Turn Off 00h FCh 0-9:Do not set. 10:10s 11:11s | 240:240s Information OSM 02h 3Dh 0:disable information OSM 3-10: OSM timer [seconds] Off Timer 02h 2Bh 0: OFF 1: 1 hour | 24: 24 hours 1 hour/step H Posi ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 37

    (37/38) Item OP code page OP code Parameter Remarks Power On Delay 02h D8h 0: OFF (0sec) │ 50:50sec Advanced Option Reset 02h E4h 1:RESET Momentary Input 00h 60h 3: RGB1 (DVI-D) 1: RGB2 (D-SUB) 2: RGB3 (BNC) 12: DVD/HD 5: VIDEO (Composite) 7: S-VIDEO Picture Mode 02h 1Ah 1: sRGB 3: Hi-Bright 4: Standard 5: Cinema SRGB: PC mode only Cinema: A/V mo ...

  • NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - page 38

    (38/38) All data are subject to change without notice. Copyright 2004-2005 NEC Display Solutions All Right Reserved This document p rovides the technical info rmation for users. NEC Disp lay Solutions reserv es the right to ch ange or modify the i n form ation containe d herei n without notice. NEC Disp lay Solutions makes no warranty for the use o ...

Производитель NEC Категория Computer Monitor

Документы, которые мы получаем от производителя устройства NEC NEC MultiSync LCD3210 LCD3210 LCD3210 мы можем разделить на несколько групп. Это в частности:
- технические чертежи NEC
- инструкции обслуживания MultiSync LCD3210 LCD3210 LCD3210
- паспорта изделия NEC
- информационные брошюры
- энергетические этикетки NEC NEC MultiSync LCD3210 LCD3210 LCD3210
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа NEC NEC MultiSync LCD3210 LCD3210 LCD3210, инструкции обслуживания, короткие инструкции или инструкции пользователя NEC NEC MultiSync LCD3210 LCD3210 LCD3210. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства NEC NEC MultiSync LCD3210 LCD3210 LCD3210, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании NEC NEC MultiSync LCD3210 LCD3210 LCD3210 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей NEC NEC MultiSync LCD3210 LCD3210 LCD3210.

Полная инструкция обслуживания NEC, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания NEC NEC MultiSync LCD3210 LCD3210 LCD3210, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся NEC NEC MultiSync LCD3210 LCD3210 LCD3210, которое найдем в данном документе
3. Советы по использованию основных функций устройства NEC NEC MultiSync LCD3210 LCD3210 LCD3210 - которые должны облегчить нам первые шаги во время использования NEC NEC MultiSync LCD3210 LCD3210 LCD3210
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем NEC NEC MultiSync LCD3210 LCD3210 LCD3210
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра NEC NEC MultiSync LCD3210 LCD3210 LCD3210 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся NEC NEC MultiSync LCD3210 LCD3210 LCD3210?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с NEC NEC MultiSync LCD3210 LCD3210 LCD3210, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с NEC NEC MultiSync LCD3210 LCD3210 LCD3210 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)