Bedienungsanleitung Zenoah G3000

20 Seiten 0.8 mb
Download

Zur Seite of 20

Summary
  • Zenoah G3000 - page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS 2631-93111(205) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMBERS : ...

  • Zenoah G3000 - page 2

    ...

  • Zenoah G3000 - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah G3000 - page 4

    2. Specifications ■ G3000 Power unit : Dis placement ········································································································ 28.5cm 3 Fuel ···································· ...

  • Zenoah G3000 - page 5

    3. Symbols on the machine  5  For safe operation and maintenance, symbols are on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the “MIX GASOLINE” Position: fuel tank cap (b). The port to refuel the “CHAIN OIL” Position: oil cap (c). The indication regarding the switch. Fl ...

  • Zenoah G3000 - page 6

     6  4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. ...

  • Zenoah G3000 - page 7

     7  4. For safe operation 16. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide b ...

  • Zenoah G3000 - page 8

    A standard saw unit package contains the items as shown. (SE1) Open the box and install the guide bar and the saw chain to the power unit as follows. The saw chain has very sharp edges. Use thick, protective gloves to avoid injury. 1. Loosen a nut and remove the chain cover. 2. Mount the guide bar and fit the saw chain around the bar and the drive ...

  • Zenoah G3000 - page 9

    6. Fuel and chain oil  9  ■ Fuel Mix a regular grade gasoline (leaded or unleaded,alcohol-free) and a quality-proven motor oil for air cooled 2 cycle engines. Recommended mixing ratio: Condition Gasoline : Oil Up to 20 hours use 20 : 1 After 20 hours use 25 : 1 25 : 1 Mix Chart Gasoline liters 1 2345 2-cycle oil ml. 40 80 120 160 200 • Ke ...

  • Zenoah G3000 - page 10

     10  ■ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely. 1. Select bare ground for fueling. 2. Move at least 10 feet (3 ...

  • Zenoah G3000 - page 11

    7. Operation 5. While holding the saw unit securely on the ground, pull the starter rope vigorously. (OP6) Do not start the engine while hanging the chain saw with a hand. The saw chain may touch your body. It's very dangerous. 6. When engine has ignited first, push in the choke knob and pull the rope again to start the engine. 7. Allow the en ...

  • Zenoah G3000 - page 12

     12  ■ ADJUSTING CARBURETOR (OP9) The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or operating conditions, please let your skillful dealer make the adjustment. A wrong adjustment may cause damage to your unit. If you have to make the adjustment yourself, please carefully fol ...

  • Zenoah G3000 - page 13

    • Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • Racing the engine with the chain seized in a ...

  • Zenoah G3000 - page 14

    SA3 SA4 SA5  14  ■ LOGGING AND LIMBING 1. Always ensure your foothold as well as stability of the tree. 2. Be alert to the rolling over of a cut log. 3. Read the instructions in “For safe operation” to avoid kickback of the saw. Before starting work, check the direction of bending force inside the log to be cut. Always finish cutting fr ...

  • Zenoah G3000 - page 15

    ● Pruning 1. Do not use an unstable foothold or a stepladder. 2. Do not overreach. 3. Do not cut above shoulder height. 4. Always use both hands to grip the saw. Cut up from the bottom, finish down from the top. (SA6) WARNING 8. Sawing SA6  15  ...

  • Zenoah G3000 - page 16

     16  9. Maintenance Make sure to stop the engine before inspecting and/or servicing the unit. ■ DAILY MAINTENANCE SAW CHAIN It is one of the essential factors for smooth and safe operation to keep the cutters always in good condition. It’s time to reform the cutters when; 1. Sawdust has become powder-like. 2. You need extra force to saw i ...

  • Zenoah G3000 - page 17

    9. Maintenance GUIDE BAR 1. Remove sawdust in the bar groove and the oiling port. (MA5) 2. Grease the nose sprocket from the feeding port on the tip of the guide bar. (MA6) 3. Periodically turn over the guide bar when mounting it to the unit, in order to prevent partial wear. 4. The bar rail should always be a square. Check for wear of the bar rail ...

  • Zenoah G3000 - page 18

     18  OILING PORT Dismount the guide bar and check the oiling port for blocking by sawdust. (MA9) GENERAL Inspect the entire unit for fuel leakage, Ioose fastenings, and damage to major parts, especially handle joints and guide bar mounting. When anything wrong be found, make sure to have it repaired before next usage. ■ MONTHLY MAINTENANCE ...

  • Zenoah G3000 - page 19

    10. Storage 1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children. 9. Maintenance  19  HANDLE MOUNTING JOINTS Inspect the handle mounting joints and replace when any adhered part is peeled off or a crack is observed on the rubber pa ...

  • Zenoah G3000 - page 20

    Head Office: 1-9, Minamidai, Kawagoe-city, Saitama, 350-1192 Japan Telephone: (+81)492-43-1117 Telecopier: (+81)492-43-7197 PRINTED IN JAPAN ...

Produzent Zenoah Kategorie Chainsaw

Dokumente, die wir vom Produzenten des Geräts Zenoah G3000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zenoah
- Bedienungsanleitungen G3000
- Produktkarten Zenoah
- Informationsbroschüren
- oder Energieetiketten Zenoah G3000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zenoah G3000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zenoah G3000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zenoah G3000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zenoah G3000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zenoah G3000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zenoah G3000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zenoah G3000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Zenoah sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zenoah G3000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zenoah G3000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zenoah G3000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zenoah G3000 - die uns die ersten Schritte während der Nutzung von Zenoah G3000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zenoah G3000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zenoah G3000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zenoah G3000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zenoah G3000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zenoah G3000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)