Italiano dropdown-ico

Manuale per l’uso Zenoah G3000

20 pagine 0.8 mb
Scarica

Vai alla pagina of 20

Summary
  • Zenoah G3000 - page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS 2631-93111(205) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMBERS : ...

  • Zenoah G3000 - page 2

    ...

  • Zenoah G3000 - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah G3000 - page 4

    2. Specifications ■ G3000 Power unit : Dis placement ········································································································ 28.5cm 3 Fuel ···································· ...

  • Zenoah G3000 - page 5

    3. Symbols on the machine  5  For safe operation and maintenance, symbols are on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the “MIX GASOLINE” Position: fuel tank cap (b). The port to refuel the “CHAIN OIL” Position: oil cap (c). The indication regarding the switch. Fl ...

  • Zenoah G3000 - page 6

     6  4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. ...

  • Zenoah G3000 - page 7

     7  4. For safe operation 16. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so. 18. Guard against kickback. Kickback is the upward motion of the guide b ...

  • Zenoah G3000 - page 8

    A standard saw unit package contains the items as shown. (SE1) Open the box and install the guide bar and the saw chain to the power unit as follows. The saw chain has very sharp edges. Use thick, protective gloves to avoid injury. 1. Loosen a nut and remove the chain cover. 2. Mount the guide bar and fit the saw chain around the bar and the drive ...

  • Zenoah G3000 - page 9

    6. Fuel and chain oil  9  ■ Fuel Mix a regular grade gasoline (leaded or unleaded,alcohol-free) and a quality-proven motor oil for air cooled 2 cycle engines. Recommended mixing ratio: Condition Gasoline : Oil Up to 20 hours use 20 : 1 After 20 hours use 25 : 1 25 : 1 Mix Chart Gasoline liters 1 2345 2-cycle oil ml. 40 80 120 160 200 • Ke ...

  • Zenoah G3000 - page 10

     10  ■ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely. 1. Select bare ground for fueling. 2. Move at least 10 feet (3 ...

  • Zenoah G3000 - page 11

    7. Operation 5. While holding the saw unit securely on the ground, pull the starter rope vigorously. (OP6) Do not start the engine while hanging the chain saw with a hand. The saw chain may touch your body. It's very dangerous. 6. When engine has ignited first, push in the choke knob and pull the rope again to start the engine. 7. Allow the en ...

  • Zenoah G3000 - page 12

     12  ■ ADJUSTING CARBURETOR (OP9) The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or operating conditions, please let your skillful dealer make the adjustment. A wrong adjustment may cause damage to your unit. If you have to make the adjustment yourself, please carefully fol ...

  • Zenoah G3000 - page 13

    • Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. • Racing the engine with the chain seized in a ...

  • Zenoah G3000 - page 14

    SA3 SA4 SA5  14  ■ LOGGING AND LIMBING 1. Always ensure your foothold as well as stability of the tree. 2. Be alert to the rolling over of a cut log. 3. Read the instructions in “For safe operation” to avoid kickback of the saw. Before starting work, check the direction of bending force inside the log to be cut. Always finish cutting fr ...

  • Zenoah G3000 - page 15

    ● Pruning 1. Do not use an unstable foothold or a stepladder. 2. Do not overreach. 3. Do not cut above shoulder height. 4. Always use both hands to grip the saw. Cut up from the bottom, finish down from the top. (SA6) WARNING 8. Sawing SA6  15  ...

  • Zenoah G3000 - page 16

     16  9. Maintenance Make sure to stop the engine before inspecting and/or servicing the unit. ■ DAILY MAINTENANCE SAW CHAIN It is one of the essential factors for smooth and safe operation to keep the cutters always in good condition. It’s time to reform the cutters when; 1. Sawdust has become powder-like. 2. You need extra force to saw i ...

  • Zenoah G3000 - page 17

    9. Maintenance GUIDE BAR 1. Remove sawdust in the bar groove and the oiling port. (MA5) 2. Grease the nose sprocket from the feeding port on the tip of the guide bar. (MA6) 3. Periodically turn over the guide bar when mounting it to the unit, in order to prevent partial wear. 4. The bar rail should always be a square. Check for wear of the bar rail ...

  • Zenoah G3000 - page 18

     18  OILING PORT Dismount the guide bar and check the oiling port for blocking by sawdust. (MA9) GENERAL Inspect the entire unit for fuel leakage, Ioose fastenings, and damage to major parts, especially handle joints and guide bar mounting. When anything wrong be found, make sure to have it repaired before next usage. ■ MONTHLY MAINTENANCE ...

  • Zenoah G3000 - page 19

    10. Storage 1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children. 9. Maintenance  19  HANDLE MOUNTING JOINTS Inspect the handle mounting joints and replace when any adhered part is peeled off or a crack is observed on the rubber pa ...

  • Zenoah G3000 - page 20

    Head Office: 1-9, Minamidai, Kawagoe-city, Saitama, 350-1192 Japan Telephone: (+81)492-43-1117 Telecopier: (+81)492-43-7197 PRINTED IN JAPAN ...

Fabbricante Zenoah Categoria Chainsaw

I documenti che otteniamo dal fabbricante del dispositivoZenoah G3000 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Zenoah
- manuali per l’uso G3000
- schede prodotto Zenoah
- opuscoli
- o etichette energetiche Zenoah G3000
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Zenoah G3000.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Zenoah G3000, manuali di manutenzione, brevi manuali o manuali utente Zenoah G3000. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Zenoah G3000.

Manuali per l’uso simili

Manuale completo del dispositivo Zenoah G3000, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Zenoah G3000 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Zenoah G3000.

Il manuale per l’uso completo Zenoah, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Zenoah G3000 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Zenoah G3000, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Zenoah G3000 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Zenoah G3000 - che ci dovrebbe aiutare nei primi passi durante l'uso Zenoah G3000
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Zenoah G3000
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Zenoah G3000 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Zenoah G3000?

Utilizza il modulo sottostante

Se non hai risolto il problema con Zenoah G3000 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Zenoah G3000 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)