Bedienungsanleitung Patton electronic PATTON 2707/I

24 Seiten 0.18 mb
Download

Zur Seite of 24

Summary
  • Patton electronic PATTON 2707/I - page 1

    USER MANUAL MODEL 2707/I G.703 NTU with 10Base-T Ethernet Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2707/I-A Doc# 086251UA Revised 10/2/01 An ISO-9001 ...

  • Patton electronic PATTON 2707/I - page 2

    2 1.0 Warranty Information .................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice ...................................................................................... 4 1.3 Service .............................................. ...

  • Patton electronic PATTON 2707/I - page 3

    3 B.9 Diagnostics ...................................................................... 21 B.10Indicators ........................................................................ 21 B.11Configuration .................................................................. 21 B.12Power Supply .............................................................. ...

  • Patton electronic PATTON 2707/I - page 4

    4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2707/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er customer damage, ab use , or ...

  • Patton electronic PATTON 2707/I - page 5

    5 als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vices at: • T el: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www .patton.com Note P ackages received without an RMA number will not be accepted. Caution This device is not intended to be c ...

  • Patton electronic PATTON 2707/I - page 6

    6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear parts and labor . If any questions or prob lems arise during installation or use of this product, please do not hesitate to contact P at- ton Electronics T echnical Suppor ...

  • Patton electronic PATTON 2707/I - page 7

    7 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, which can be divided into the f ollowing main components: • A standard method to encapsulate datagrams o v er serial links • A Link Control Protocol ...

  • Patton electronic PATTON 2707/I - page 8

    8 Figure 1. Cisco router with serial interface, configured as PPP Half Bridge. Figure 1 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router ser ial interf ace connects to the W AN via a 2707/C (V .35) E1 NTU and to the remote 2707/I with suppor t for PPP bridging. The 2707/I functions as a node on the ...

  • Patton electronic PATTON 2707/I - page 9

    9 4.0 CONFIGURATION The Model 2707/I f eatures configuration capability via hardware DIP s witches. This section describes all possib le DIP s witch configur ations of the Model 2707/I. 4.1 DIP SWITCH CONFIGURATIONS The Model 2707/I has an internal DIP switch that enables configur ation f or a wide range of applications. The DIP switch is access ...

  • Patton electronic PATTON 2707/I - page 10

    10 Switch S1 settings T able 1 sho ws the settings f or DIP switch S1-1 thru S1-8. SW1-1 Line Coding: HDB3 (default) Use Switch SW1-1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to y ou by your Service Provider . If you are using tw o Model 2707/Is together as shor t range modems, set both u ...

  • Patton electronic PATTON 2707/I - page 11

    11 The receiver recogniz es these special violations and decodes them as zeros . This method enables the network to meet minimum pulse den- sity requirements. Unless AMI is required in your application, HDB3 should be used whene ver possib le. • AMI . Alter nate Mark Inv ersion defines a pulse as a "mark, ” a binar y one, as opposed to a ...

  • Patton electronic PATTON 2707/I - page 12

    12 5.0 INSTALLATION Once the Model 2707/I is properly configured, it is ready to connect to the G.703 interf ace, to the Ethernet por t, and to the power source. This section describes how to make these connections . 5.1 CONNECTING TO THE G.703 NETWORK AND ETHERNET LAN This section describes installing the G.703 (75-ohm and 120-ohm), Ethernet LAN, ...

  • Patton electronic PATTON 2707/I - page 13

    13 Connecting Dual Coaxial Cable (75 ohm) to the G.703 Netw ork Ref er to Figure 5 to make the proper connections . Figure 5. Rear panel, showing location of connectors Note The outer conductor of the coax cables are isolated from system ear th ground. When using the 75-ohm interf ace, jumper straps JP2, JP5, JP6, and JP7 must be installed ov er th ...

  • Patton electronic PATTON 2707/I - page 14

    14 Connecting the T wisted Pair (120 ohm) to the G.703 Network Ref er to the pinout and signals chart in Figure 6 to connect the 120-ohm G.703 network channel. Figure 6. G.703 120-ohm connection. Connecting the 10Base-T Ethernet por t to a PC (DTE) T o connect the Model 2707/I to another DTE de vice such as a 10Base-T network interface card, constr ...

  • Patton electronic PATTON 2707/I - page 15

    15 Figure 8. 10Base-T cross-ov er cable connection Connecting the 10Base-T Ethernet P or t to a Hub The 10Base-T interf ace is configured as DTE (data terminal equipment), just like a 10Base-T netw ork interface card in a PC . Theref ore, it “e xpects” to connect to a 10Base-T Hub using a straight-through RJ-45 cable . Refer to Figure 9 below ...

  • Patton electronic PATTON 2707/I - page 16

    16 DC Power . The 36–60 VDC DC-to-DC adapter supplied with the DC ver- sion of the Model 2707/I plugs in a DC source (nominal 48 VDC) and plugs into the barrel power supply jac k on the rear of the 2707/I. Refer to Figure 10 to make the proper connection. Figure 10. Connecting DC power to the 2707/I DC po wer supply T o power supply jack T o -48 ...

  • Patton electronic PATTON 2707/I - page 17

    17 6.0 OPERATION When the Model 2707/I has been properly configured and installed, it should operate transparently . This section descr ibes power-up , LED sta- tus monitors, and the b uilt-in loopback test modes . 6.1 POWER-UP Bef ore applying power to the Model 2707/I, please re view section “P ower Connection” on page 15 to verify that the ...

  • Patton electronic PATTON 2707/I - page 18

    18 T able 2: LED descriptions LED Description E1 Link (Active Green) Solid g reen (On) indicates that the end to end E1 Link is up , signifying that the link is active . The E1 Link LED is Off when the link is down. 10BT Link (Active Green) Solid green indicates that the 10Base-T Ethernet interface has detected a v alid SQE hear tbeat, signifying a ...

  • Patton electronic PATTON 2707/I - page 19

    19 6.3 OPERATING LINE LOOPBACK (LL) The Line Loopback (LL) test chec ks the operation of the local Model 2707/I, and is perf ormed separately on each unit. Figure 12. Line loopback f or a networ k ter mination application T o perf orm an LL test, set DIP switch S1-2 to On . The TM LED will be lit while the unit is in loopback test mode . Model 2707 ...

  • Patton electronic PATTON 2707/I - page 20

    20 APPENDIX A G.703 SPECIFICATIONS A.1 NETWORK DATA RATE 2.048 Mbps A.2 NETWORK CONNECTOR RJ-48C/Dual Coax BNC A.3 NOMINAL IMPEDANCE 75/120 ohm A.4 LINE CODING Selectable AMI or HDB3 A.5 LINE FRAMING G.703 (Unframed) A.6 CLOCKING Internal or Networ k (Receive Reco ver) A.7 DISTANCE Maximum 6,000 ft (1.6 km) On 24 A WG cable ...

  • Patton electronic PATTON 2707/I - page 21

    21 APPENDIX B ETHERNET 10BASE-T SPECIFICATIONS B.1 DTE INTERFACE 10Base-T on RJ-45F B.2 DTE DATA RATES 10 Mbps B.3 LAN CONNECTION RJ-45, 10Base-T , 802.3 Ethernet B.4 PROTOCOL PPP (RFC 1661) with Bridging Control (RFC 1638) B.5 MAC ADDR ESS T ABLE SIZE 4096 entries B.6 MAC ADDR ESS AGING MA C addresses deleted after 8 minutes of inactivity B.7 FRAM ...

  • Patton electronic PATTON 2707/I - page 22

    22 B.12 POWER SUPPLY 5 VDC external power supply 100–240V AC , 50–60Hz, 0.4A B.13 HUMIDITY Up to 90% non-condensing B.14 T EMPERATURE 0–50°C (32–122°F) B.15 DIMENSIONS 3.5L x 2.1W x 0.78H in.(9.0L x 5.3W x 2.0H cm) ...

  • Patton electronic PATTON 2707/I - page 23

    23 APPENDIX C F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES P atton Model # Description 2707/C G.703 NTU with a V .35 interface 2707/D G.703 NTU with an X.21 interf ace 2707/I G.7034 NTU with 10Base-T ethernet interface 08055DCUI Universal Input P ower Supply 07M2707/I User Manual ...

  • Patton electronic PATTON 2707/I - page 24

    24 Cop yright © 2000, 2001 P atton Electronics Company All Rights Reser ved. ...

Produzent Patton electronic Kategorie Network Card

Dokumente, die wir vom Produzenten des Geräts Patton electronic PATTON 2707/I erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Patton electronic
- Bedienungsanleitungen PATTON 2707/I
- Produktkarten Patton electronic
- Informationsbroschüren
- oder Energieetiketten Patton electronic PATTON 2707/I
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Patton electronic PATTON 2707/I.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Patton electronic PATTON 2707/I, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Patton electronic PATTON 2707/I. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Patton electronic PATTON 2707/I ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Patton electronic PATTON 2707/I, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Patton electronic PATTON 2707/I hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Patton electronic PATTON 2707/I verständlich ist.

Eine gänzliche Bedienungsanleitung von Patton electronic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Patton electronic PATTON 2707/I bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Patton electronic PATTON 2707/I befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Patton electronic PATTON 2707/I, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Patton electronic PATTON 2707/I - die uns die ersten Schritte während der Nutzung von Patton electronic PATTON 2707/I erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Patton electronic PATTON 2707/I hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Patton electronic PATTON 2707/I im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Patton electronic PATTON 2707/I?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Patton electronic PATTON 2707/I nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Patton electronic PATTON 2707/I hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)