Italiano dropdown-ico

Manuale per l’uso Patton electronic PATTON 2707/I

24 pagine 0.18 mb
Scarica

Vai alla pagina of 24

Summary
  • Patton electronic PATTON 2707/I - page 1

    USER MANUAL MODEL 2707/I G.703 NTU with 10Base-T Ethernet Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2707/I-A Doc# 086251UA Revised 10/2/01 An ISO-9001 ...

  • Patton electronic PATTON 2707/I - page 2

    2 1.0 Warranty Information .................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice ...................................................................................... 4 1.3 Service .............................................. ...

  • Patton electronic PATTON 2707/I - page 3

    3 B.9 Diagnostics ...................................................................... 21 B.10Indicators ........................................................................ 21 B.11Configuration .................................................................. 21 B.12Power Supply .............................................................. ...

  • Patton electronic PATTON 2707/I - page 4

    4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2707/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er customer damage, ab use , or ...

  • Patton electronic PATTON 2707/I - page 5

    5 als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vices at: • T el: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www .patton.com Note P ackages received without an RMA number will not be accepted. Caution This device is not intended to be c ...

  • Patton electronic PATTON 2707/I - page 6

    6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear parts and labor . If any questions or prob lems arise during installation or use of this product, please do not hesitate to contact P at- ton Electronics T echnical Suppor ...

  • Patton electronic PATTON 2707/I - page 7

    7 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, which can be divided into the f ollowing main components: • A standard method to encapsulate datagrams o v er serial links • A Link Control Protocol ...

  • Patton electronic PATTON 2707/I - page 8

    8 Figure 1. Cisco router with serial interface, configured as PPP Half Bridge. Figure 1 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router ser ial interf ace connects to the W AN via a 2707/C (V .35) E1 NTU and to the remote 2707/I with suppor t for PPP bridging. The 2707/I functions as a node on the ...

  • Patton electronic PATTON 2707/I - page 9

    9 4.0 CONFIGURATION The Model 2707/I f eatures configuration capability via hardware DIP s witches. This section describes all possib le DIP s witch configur ations of the Model 2707/I. 4.1 DIP SWITCH CONFIGURATIONS The Model 2707/I has an internal DIP switch that enables configur ation f or a wide range of applications. The DIP switch is access ...

  • Patton electronic PATTON 2707/I - page 10

    10 Switch S1 settings T able 1 sho ws the settings f or DIP switch S1-1 thru S1-8. SW1-1 Line Coding: HDB3 (default) Use Switch SW1-1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to y ou by your Service Provider . If you are using tw o Model 2707/Is together as shor t range modems, set both u ...

  • Patton electronic PATTON 2707/I - page 11

    11 The receiver recogniz es these special violations and decodes them as zeros . This method enables the network to meet minimum pulse den- sity requirements. Unless AMI is required in your application, HDB3 should be used whene ver possib le. • AMI . Alter nate Mark Inv ersion defines a pulse as a "mark, ” a binar y one, as opposed to a ...

  • Patton electronic PATTON 2707/I - page 12

    12 5.0 INSTALLATION Once the Model 2707/I is properly configured, it is ready to connect to the G.703 interf ace, to the Ethernet por t, and to the power source. This section describes how to make these connections . 5.1 CONNECTING TO THE G.703 NETWORK AND ETHERNET LAN This section describes installing the G.703 (75-ohm and 120-ohm), Ethernet LAN, ...

  • Patton electronic PATTON 2707/I - page 13

    13 Connecting Dual Coaxial Cable (75 ohm) to the G.703 Netw ork Ref er to Figure 5 to make the proper connections . Figure 5. Rear panel, showing location of connectors Note The outer conductor of the coax cables are isolated from system ear th ground. When using the 75-ohm interf ace, jumper straps JP2, JP5, JP6, and JP7 must be installed ov er th ...

  • Patton electronic PATTON 2707/I - page 14

    14 Connecting the T wisted Pair (120 ohm) to the G.703 Network Ref er to the pinout and signals chart in Figure 6 to connect the 120-ohm G.703 network channel. Figure 6. G.703 120-ohm connection. Connecting the 10Base-T Ethernet por t to a PC (DTE) T o connect the Model 2707/I to another DTE de vice such as a 10Base-T network interface card, constr ...

  • Patton electronic PATTON 2707/I - page 15

    15 Figure 8. 10Base-T cross-ov er cable connection Connecting the 10Base-T Ethernet P or t to a Hub The 10Base-T interf ace is configured as DTE (data terminal equipment), just like a 10Base-T netw ork interface card in a PC . Theref ore, it “e xpects” to connect to a 10Base-T Hub using a straight-through RJ-45 cable . Refer to Figure 9 below ...

  • Patton electronic PATTON 2707/I - page 16

    16 DC Power . The 36–60 VDC DC-to-DC adapter supplied with the DC ver- sion of the Model 2707/I plugs in a DC source (nominal 48 VDC) and plugs into the barrel power supply jac k on the rear of the 2707/I. Refer to Figure 10 to make the proper connection. Figure 10. Connecting DC power to the 2707/I DC po wer supply T o power supply jack T o -48 ...

  • Patton electronic PATTON 2707/I - page 17

    17 6.0 OPERATION When the Model 2707/I has been properly configured and installed, it should operate transparently . This section descr ibes power-up , LED sta- tus monitors, and the b uilt-in loopback test modes . 6.1 POWER-UP Bef ore applying power to the Model 2707/I, please re view section “P ower Connection” on page 15 to verify that the ...

  • Patton electronic PATTON 2707/I - page 18

    18 T able 2: LED descriptions LED Description E1 Link (Active Green) Solid g reen (On) indicates that the end to end E1 Link is up , signifying that the link is active . The E1 Link LED is Off when the link is down. 10BT Link (Active Green) Solid green indicates that the 10Base-T Ethernet interface has detected a v alid SQE hear tbeat, signifying a ...

  • Patton electronic PATTON 2707/I - page 19

    19 6.3 OPERATING LINE LOOPBACK (LL) The Line Loopback (LL) test chec ks the operation of the local Model 2707/I, and is perf ormed separately on each unit. Figure 12. Line loopback f or a networ k ter mination application T o perf orm an LL test, set DIP switch S1-2 to On . The TM LED will be lit while the unit is in loopback test mode . Model 2707 ...

  • Patton electronic PATTON 2707/I - page 20

    20 APPENDIX A G.703 SPECIFICATIONS A.1 NETWORK DATA RATE 2.048 Mbps A.2 NETWORK CONNECTOR RJ-48C/Dual Coax BNC A.3 NOMINAL IMPEDANCE 75/120 ohm A.4 LINE CODING Selectable AMI or HDB3 A.5 LINE FRAMING G.703 (Unframed) A.6 CLOCKING Internal or Networ k (Receive Reco ver) A.7 DISTANCE Maximum 6,000 ft (1.6 km) On 24 A WG cable ...

  • Patton electronic PATTON 2707/I - page 21

    21 APPENDIX B ETHERNET 10BASE-T SPECIFICATIONS B.1 DTE INTERFACE 10Base-T on RJ-45F B.2 DTE DATA RATES 10 Mbps B.3 LAN CONNECTION RJ-45, 10Base-T , 802.3 Ethernet B.4 PROTOCOL PPP (RFC 1661) with Bridging Control (RFC 1638) B.5 MAC ADDR ESS T ABLE SIZE 4096 entries B.6 MAC ADDR ESS AGING MA C addresses deleted after 8 minutes of inactivity B.7 FRAM ...

  • Patton electronic PATTON 2707/I - page 22

    22 B.12 POWER SUPPLY 5 VDC external power supply 100–240V AC , 50–60Hz, 0.4A B.13 HUMIDITY Up to 90% non-condensing B.14 T EMPERATURE 0–50°C (32–122°F) B.15 DIMENSIONS 3.5L x 2.1W x 0.78H in.(9.0L x 5.3W x 2.0H cm) ...

  • Patton electronic PATTON 2707/I - page 23

    23 APPENDIX C F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES P atton Model # Description 2707/C G.703 NTU with a V .35 interface 2707/D G.703 NTU with an X.21 interf ace 2707/I G.7034 NTU with 10Base-T ethernet interface 08055DCUI Universal Input P ower Supply 07M2707/I User Manual ...

  • Patton electronic PATTON 2707/I - page 24

    24 Cop yright © 2000, 2001 P atton Electronics Company All Rights Reser ved. ...

Fabbricante Patton electronic Categoria Network Card

I documenti che otteniamo dal fabbricante del dispositivoPatton electronic PATTON 2707/I possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Patton electronic
- manuali per l’uso PATTON 2707/I
- schede prodotto Patton electronic
- opuscoli
- o etichette energetiche Patton electronic PATTON 2707/I
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Patton electronic PATTON 2707/I.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Patton electronic PATTON 2707/I, manuali di manutenzione, brevi manuali o manuali utente Patton electronic PATTON 2707/I. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Patton electronic PATTON 2707/I.

Manuali per l’uso simili

Manuale completo del dispositivo Patton electronic PATTON 2707/I, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Patton electronic PATTON 2707/I dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Patton electronic PATTON 2707/I.

Il manuale per l’uso completo Patton electronic, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Patton electronic PATTON 2707/I - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Patton electronic PATTON 2707/I, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Patton electronic PATTON 2707/I che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Patton electronic PATTON 2707/I - che ci dovrebbe aiutare nei primi passi durante l'uso Patton electronic PATTON 2707/I
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Patton electronic PATTON 2707/I
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Patton electronic PATTON 2707/I in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Patton electronic PATTON 2707/I?

Utilizza il modulo sottostante

Se non hai risolto il problema con Patton electronic PATTON 2707/I con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Patton electronic PATTON 2707/I è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)