-
Sunfire HRS-12 - page 1
User's Manual High Resolution Series Subwoofer HRS-8, HRS-10, and HRS-12 ...
-
Sunfire HRS-12 - page 2
User's Manual 2 Important Safety Instructions 1. Read Instructions 2. Keep these Instructions 3. Heed all W arnings. 4. Follow all Instructions 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) tha ...
-
Sunfire HRS-12 - page 3
User's Manual 3 Contents T o nd out more about this and other Sunre products, please visit our website: www .sunre.com W ARNING: THIS SUBWOOFER IS CAP ABLE OF PRODUCING VERY HIGH SOUND PRESSURE LEVELS. YOU MUST T AKE EVERY PRECAUTION T O PROTECT YOUR HEARING FROM PERMANENT DAMAGE. Safety Instructions .................................. ...
-
Sunfire HRS-12 - page 4
User's Manual 4 Features • Patented high-pressure, High Back- emf, extra-long-throw design • High efciency T racking Downconverter amplier • Low distortion • Premium quality driver • Extremely compact size • Automatic signal-sensing turn-on and standby mode • Line-level inputs • Speaker-level binding post inputs • Line- ...
-
Sunfire HRS-12 - page 5
User's Manual 5 Overview The Sunre HRS subwoofers are designed to give you the best possible low-frequency sound quality for your Home Theater and music playback expe- rience. They incorporate a tremendously powerful built-in amplier to produce tight, seismic, denture-rumbling bass that you can feel as well as hear . There are three mode ...
-
Sunfire HRS-12 - page 6
User's Manual 6 1. Power Indicator This light is bright when the subwoofer is on, and dim when the subwoofer is in standby mode. 2. Power Switch Press the top of this rocker switch to turn on the subwoofer . The subwoofer has an automatic signal-detection circuit. After approxi- mately fteen minutes with no signal, the subwoofer will go int ...
-
Sunfire HRS-12 - page 7
User's Manual 7 6. Line-Level Inputs These connect with RCA type cables from the line-level outputs of your receiver or preamp. Here are two examples: If your processor or receiver has a single subwoofer output, connect it to the subwoofer ’s left input jack (see page 1 1). There is no need to use the subwoofer ’s right input jack. If your ...
-
Sunfire HRS-12 - page 8
User's Manual 8 Installation Observe the following general precau- tions and read the safety instructions on pages 2 and 3 before using your Subwoofer . • Never open the cabinet or remove the metal control panel as this might result in an electrical shock to you or damage to the unit. • Protect the subwoofer from prolonged exposure to dire ...
-
Sunfire HRS-12 - page 9
User's Manual 9 Please consider the following when set- ting up your new system : • Before making or changing any connections, AL WA YS make sure that the subwoofer and your other components are turned OFF . T urn down the volume control of both the subwoofer and your processor or receiver . • This diagram shows all the low power component ...
-
Sunfire HRS-12 - page 10
User's Manual 10 Here is a neat trick to nd the best subwoofer location for your room: 1. Start by placing it right on the seat of your favorite couch or easy chair . (This method is odd, but it is based on principles of acoustic physics). 2. If the subwoofer is part of a Home Theater system you can use the calibration test tone (pink noise ...
-
Sunfire HRS-12 - page 11
User's Manual 1 1 System Congurations The following pages show some typical connections that you might make in your installation. They show how the inputs and outputs of the Sunre Subwoofer are connected to your preamplier or receiver . If your processor or receiver has a subwoofer output (Sub/LFE), it should be connected to the sub- ...
-
Sunfire HRS-12 - page 12
User's Manual 12 If your processor does not have a Sub/LFE output, you can use “Y” cables (or Y adaptors) to send its left and right main outputs to both the subwoofer and your amplier . The subwoofer will play the low frequency range, and your front speakers will play the full range. Although bass is commonly distributed evenly between ...
-
Sunfire HRS-12 - page 13
User's Manual 13 If you are using a receiver or processor which does not have a Sub/LFE output, you can send its left and right front output into the subwoofer ’s Line-Level inputs and then connect the subwoofer ’s High-Pass outputs to the inputs of your amplier . The subwoofer will play the low frequencies, and your amplier and fron ...
-
Sunfire HRS-12 - page 14
User's Manual 14 If you are using a receiver which does not have a subwoofer output or line-level outputs (pre-outs), you can connect its speaker outputs to the subwoofer ’s speaker-level inputs. The front speakers can still be connected to your receiver . The subwoofer ’s internal amplier supplies the power to reproduce the low frequen ...
-
Sunfire HRS-12 - page 15
User's Manual 15 There are two main methods for adjust- ing the volume, crossover frequency and phase controls to match a system: • Preferred method: By listening and making the adjustments to suit your taste. • Laboratory method: By measur- ing the output with a microphone and adjusting for a at frequency response. Excellent results ca ...
-
Sunfire HRS-12 - page 16
User's Manual 16 Specications Amplier Output 1,000 watts rms High Cut Filter 30 Hz - 100 Hz adjustable. The crossover can be bypassed by rotating the crossover frequency control fully clockwise. Frequency Response HRS-8 22 Hz - 100 Hz HRS-10 20 Hz - 100 Hz HRS-12 18 Hz - 100 Hz Power Line V oltage 120 V AC 50/60 Hz version 230 V AC 50/60 ...
-
Sunfire HRS-12 - page 17
User's Manual 17 T roubleshooting This subwoofer has been designed and built to provide years of trouble-free performance. Most problems that occur can usually be solved by checking your setup, or by making sure that the compo- nents connected to the amplier are on and fully operational. The following information will help you deal with com ...
-
Sunfire HRS-12 - page 18
User's Manual 18 Hum Adding any component such as a sub- woofer to an existing system will often give rise to a hum which wasn’t there before. Y our rst thought may be that the subwoofer has a problem, but this is more than likely caused by a “ground- loop” in your system. Follow these steps to isolate the main cause of the ground-loo ...
-
Sunfire HRS-12 - page 19
User's Manual 19 Limited W arranty Sunre Corporation is proud of its products which have been built with care using advanced technology and premium component parts. Y our unit has been crafted to perform properly for many years. Sunre Corporation offers the following W arranty to you, the owner of a new Sunre product: The Sunre Cor ...
-
Sunfire HRS-12 - page 20
Manual part number 913-140-00 Rev B High Resolution Series Subwoofer HRS-8, HRS-10, and HRS-12 ...
Haben Sie eine Frage bezüglich Sunfire HRS-12?
Nutzen Sie das untere Formular
Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Sunfire HRS-12 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Sunfire HRS-12 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.