Bedienungsanleitung NetComm NP2008

12 Seiten 1.28 mb
Download

Zur Seite of 12

Summary
  • NetComm NP2008 - page 1

    NetComm Limited 2~6 Orion Road, Lane Cove, NSW, 2066 Tel: (02) 9424 - 2070, Fax: (02) 9424 - 2010 Web: www.netcomm.com.au User Installation Guide NP2008 8 - Port Net work SmartS witch ...

  • NetComm NP2008 - page 2

    Table of Contents Table of contents Page 2 Introduction Page 3 Key features Page 3 Package contents Page 4 Front panel Page 4 LED’s Page 4 Rear panel Page 5 RJ - 45 Network ports Page 5 Twisted pair cables Page 5 Straight and crossover cable configuration Page 6 Application examples Page 6 Preparation before connecting your switch Page 7 Attachin ...

  • NetComm NP2008 - page 3

    Introduction Your NetComm™ NP2008 8 port 10/100 Ethernet Switch provides you with a cost effective, high - performance network sw itching solution for the home or small office. It is designed to automatically support network users operating at any combinatio n of 10 megabits per second (Mbps) or 100 Mbps. W ith features such as auto - negotiation ...

  • NetComm NP2008 - page 4

    Package contents Your package will contain the following: • NP2008 switch • User installation guide • Power Supply • Self adhesive rub ber feet • Wall mounting plugs and screws Front panel The front panel of the NP2008 switch contains LED’s corresponding to each network port located on the back of the hub: • 100 Mbps (10 Mbps). • Li ...

  • NetComm NP2008 - page 5

    R ear panel The rear panel of the NP2008 switch has eight auto - sensing 10/100 Mbps Ethernet ports and a power jack for connection of the supplied plug - pack. RJ - 45 Network ports All of the ports on the NP2008 are 10/100 Mbps capable auto - sensing Ethernet ports. Each port supports only unshielded twisted pair (UTP) cable using an 8 - pin RJ - ...

  • NetComm NP2008 - page 6

    S traight and crossover cable configuration For two devices to communicate, the transmitter of each device must be co n- nected to the receiver of the other device. The crossover function is usually implemented internally as part of the circuitry in the device. Most ports on switches and repeaters have media - dependent interfaces with crossover po ...

  • NetComm NP2008 - page 7

    Basic Desktop Network Switch The NP2008 switch is used as a desktop switch to build a small network that enables its users to have 100 Mbps access to other PC’s on the ne t- work and share files and resources. Preparation before connecting your switch Before you install your switch, prepare for the installation. Make sure you will be operating th ...

  • NetComm NP2008 - page 8

    A ttaching computers to the switch 1. Install a 10/100Mbps (10/100Base - TX) network adapter card into every computer you want to attach to the network. Make sure you install the Network adaptor drivers in accordance with the manufa c- turers directions. 2. Prepare the twisted - pair cables with RJ - 45 plugs on each end. Use Category 5/5e cable fo ...

  • NetComm NP2008 - page 9

    C ascading the switch When attaching the NP2008 switch to an additional switch, router or other devices, be sure to verify the port type implemented before co n- nec t ing any cable. A) Connecting the NP2008 to another NP2008: Your NP2008 switch supports a switch selectable UP - Link port, port 8 located on the rear of the switch. To connect one sw ...

  • NetComm NP2008 - page 10

    1. Locate the UP - Link slide switch located on the right hand side of the switch case. 2. Slide the selection switch to the UP - Link pos ition. 3. Connect one end of a straight through cable to the number 8 port on the first NP2008 switch. 4. Connect the other end of the straight through cable to any port of the second NP2008 switch, see previous ...

  • NetComm NP2008 - page 11

    Specifications of the switch Standard IEEE802.3 10Base - T Ethernet IEEE 802.3u & 802.3x 100 Base - TX Fast Ethernet Network Interface Eight 100BASE - TX / 10BASE - T N - Wa y ports Data Transfer Rate Ethernet: 10Mbps (half duplex) 20Mbps (full duplex) Fast Ethernet: 100Mbps (half duplex) 200Mbps (full duplex) Network Cable 10 BASE - T: Cat.3, ...

  • NetComm NP2008 - page 12

    C - Tick Mark declaration of conformance This is to certify that this product complies with the Australian C - Tick sta n dard where applicable. Warning Do not plug a phone jack connector into any of th e RJ - 45 port. This may damage the switch. Sta tement of conditions In the interest of improving internal design, operational function, and/or rel ...

Produzent NetComm Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts NetComm NP2008 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen NetComm
- Bedienungsanleitungen NP2008
- Produktkarten NetComm
- Informationsbroschüren
- oder Energieetiketten NetComm NP2008
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung NetComm NP2008.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen NetComm NP2008, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen NetComm NP2008. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts NetComm NP2008 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts NetComm NP2008, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von NetComm NP2008 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von NetComm NP2008 verständlich ist.

Eine gänzliche Bedienungsanleitung von NetComm sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von NetComm NP2008 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von NetComm NP2008 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich NetComm NP2008, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts NetComm NP2008 - die uns die ersten Schritte während der Nutzung von NetComm NP2008 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit NetComm NP2008 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von NetComm NP2008 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich NetComm NP2008?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit NetComm NP2008 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit NetComm NP2008 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)