Bedienungsanleitung Husqvarna CT16

15 Seiten 0.42 mb
Download

Zur Seite of 15

Summary
  • Husqvarna CT16 - page 1

    CT16 Owner's Manual 601 00 18-54 Reference No. 337411 05/03/95 8 1.1996 Spare P ar ts Piéces Dètachées ...

  • Husqvarna CT16 - page 2

    2 SAFETY RULES THESE SAFETY RULES ARE FOR YOUR PROTECTION. READ THEM CAREFULLY LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR TILLER/ CULTIVATOR IS EQUIPPED WITH SUCH CONT ...

  • Husqvarna CT16 - page 3

    3 Record the following information about your unit so that you will be able to provide it in case of loss or theft. CITY: STATE: TELEPHONE: PURCHASE DATE: MODEL NUMBER: / / SERIAL NO.: CODE NO.: (Enter complete 8 digit number from model plate on unit) DEALER'S NAME AND ADDRESS: WARNING : This unit is equipped with an internal combustion engine ...

  • Husqvarna CT16 - page 4

    4 Figure 4 Figure 5 LOWER END OF HANDLE TINE SHIELD MOUNTING CHANNEL FIG. 1-OP on page 6 shows the tiller/cultivator completely assembled. Reference to the right and left hand side of the tiller/cultivator is from the operator's position behind the unit. TO INSTALL THE HANDLE ASSEMBLY The lower handles have a short bend at the bottom end and a ...

  • Husqvarna CT16 - page 5

    5 IMPORTANT: OVERTIGHTENING THE SCREWS ENOUGH TO CHANGE THE SHAPE OF THE HANDLES CAN RESULT IN DAMAGE TO THE ENGINE CASTING. ● Hold the curved head carriage bolt against theoutside of the lower handle while tightening the tee knobs securely. TO INSTALL THE THROTTLE CON- TROL ASSEMBLY ● Place a No. 10 x 1-1/2 inch hex head screw down through the ...

  • Husqvarna CT16 - page 6

    7 UPPER HANDLE THROTTLE CONTROL LEFT SIDE LOWER HANDLE TINE SHIELD DEPTH ROD/ TRANSPORT WHEELS RIGHT SIDE LOWER HANDLE CULTIVATOR TINES THROTTLE CONTROL - Controls the engine speed and the tine rotation. This tiller/cultivator is equipped with a centrifugal clutch that engages the tine drive system when the engine speed is increased. CHOKE CONTROL ...

  • Husqvarna CT16 - page 7

    8 The operation of this tiller/cultivator can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the tiller/cultivator. We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses. CAUTION: KEEP AWAY FROM THE ROTATING PARTS. ...

  • Husqvarna CT16 - page 8

    9 GAS OIL GAS OIL 1 Gal. 5 oz. 4 Liters .167 L 2 Gal. 11 oz. 8 Liters .333 L 5 Gal. 27 oz. 20 Liters .833 L U. S. S. I. (METRIC) ● Tilt the tiller/cultivator back on the depth rod or transport wheels to raise the tines off the ground. ● Grasp the upper handle firmly to stabilize the tiller/cultivator and pull the starter handle with short quick ...

  • Husqvarna CT16 - page 9

    10 FIGURE 7 DEPTH ROD IN TILLING POSITION FIG. 2-OP TILLING HINTS ● Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. Tilling will also clear the soil of unwanted vegetation. The decomposi tion of this vegetation matter enriches the soil. De ...

  • Husqvarna CT16 - page 10

    11 GENERAL The warranty on this tiller/cultivator does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain the tiller/cultivator as instructed in this manual. The follow SERVICE DATES SCHEDULE Tighten All Screws and Nuts After first 2 Hours Every 25 Hours Ev ...

  • Husqvarna CT16 - page 11

    12 ENGINE AIR CLEANER The air cleaner filter should be cleaned and reoiled after 3 months or 25 hours of operation. Clean more often under dusty conditions. IMPORTANT: The engine can be worn out in a very short period of time if dirt or grit is allowed to enter the engine. To clean the air filter, do the following: ● Loosen screws on air cleaner ...

  • Husqvarna CT16 - page 12

    13 LEFT SIDE TINES RIGHT SIDE TINES CLEVIS PINS HAIRPINS FRONT VIEW RIGHT SIDE INDICATOR PROPERLY INSTALLED RIGHT SIDE TINES TINE REPLACEMENT The tiller/cultivator is left hand or right hand as viewed from the operator's position behind the unit. All four tines on this unit are different and cannot be inter- changed. The tines must be properly ...

  • Husqvarna CT16 - page 13

    14 CARBURETOR ADJUSTMENT A dirty air cleaner will cause the engine to run improperly and/or smoke excessively. Be sure the air cleaner is clean before adjusting the carburetor. Never make unnecessary adjustments to the carburetor. The carburetor was set at the factory to operate efficiently under most applications. How- ever, if adjustments are req ...

  • Husqvarna CT16 - page 14

    15 ● Drain the fuel from the fuel tank into an approved container outdoors, away from open flame. ● Start and run the engine until it stops due to lack of fuel. ● Pull the starter handle slowly until you feel resistance due to compression pressure, then stop. ● Release the starter tension slowly to prevent the engine from reversing due to c ...

  • Husqvarna CT16 - page 15

    16 Drain fuel tank. Fill with fresh mixture. Check fuel mix chart and mix fresh fuel. Clean fuel tank. Fuel tank should be half full when starting engine. See carburetor adjustment section. Clean and re-gap plug. Clean and re-oil air cleaner. Blow dirt and debris off top of carburetor. Clean and re-oil air cleaner. Check fuel mix chart and mix fres ...

Produzent Husqvarna Kategorie Brush Cutter

Dokumente, die wir vom Produzenten des Geräts Husqvarna CT16 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Husqvarna
- Bedienungsanleitungen CT16
- Produktkarten Husqvarna
- Informationsbroschüren
- oder Energieetiketten Husqvarna CT16
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Husqvarna CT16.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Husqvarna CT16, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Husqvarna CT16. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Husqvarna CT16 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Husqvarna CT16, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Husqvarna CT16 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Husqvarna CT16 verständlich ist.

Eine gänzliche Bedienungsanleitung von Husqvarna sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Husqvarna CT16 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Husqvarna CT16 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Husqvarna CT16, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Husqvarna CT16 - die uns die ersten Schritte während der Nutzung von Husqvarna CT16 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Husqvarna CT16 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Husqvarna CT16 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Husqvarna CT16?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Husqvarna CT16 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Husqvarna CT16 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)