Husqvarna CT16の取扱説明書

15ページ 0.42 mb
ダウンロード

ページに移動 of 15

Summary
  • Husqvarna CT16 - page 1

    CT16 Owner's Manual 601 00 18-54 Reference No. 337411 05/03/95 8 1.1996 Spare P ar ts Piéces Dètachées ...

  • Husqvarna CT16 - page 2

    2 SAFETY RULES THESE SAFETY RULES ARE FOR YOUR PROTECTION. READ THEM CAREFULLY LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR TILLER/ CULTIVATOR IS EQUIPPED WITH SUCH CONT ...

  • Husqvarna CT16 - page 3

    3 Record the following information about your unit so that you will be able to provide it in case of loss or theft. CITY: STATE: TELEPHONE: PURCHASE DATE: MODEL NUMBER: / / SERIAL NO.: CODE NO.: (Enter complete 8 digit number from model plate on unit) DEALER'S NAME AND ADDRESS: WARNING : This unit is equipped with an internal combustion engine ...

  • Husqvarna CT16 - page 4

    4 Figure 4 Figure 5 LOWER END OF HANDLE TINE SHIELD MOUNTING CHANNEL FIG. 1-OP on page 6 shows the tiller/cultivator completely assembled. Reference to the right and left hand side of the tiller/cultivator is from the operator's position behind the unit. TO INSTALL THE HANDLE ASSEMBLY The lower handles have a short bend at the bottom end and a ...

  • Husqvarna CT16 - page 5

    5 IMPORTANT: OVERTIGHTENING THE SCREWS ENOUGH TO CHANGE THE SHAPE OF THE HANDLES CAN RESULT IN DAMAGE TO THE ENGINE CASTING. ● Hold the curved head carriage bolt against theoutside of the lower handle while tightening the tee knobs securely. TO INSTALL THE THROTTLE CON- TROL ASSEMBLY ● Place a No. 10 x 1-1/2 inch hex head screw down through the ...

  • Husqvarna CT16 - page 6

    7 UPPER HANDLE THROTTLE CONTROL LEFT SIDE LOWER HANDLE TINE SHIELD DEPTH ROD/ TRANSPORT WHEELS RIGHT SIDE LOWER HANDLE CULTIVATOR TINES THROTTLE CONTROL - Controls the engine speed and the tine rotation. This tiller/cultivator is equipped with a centrifugal clutch that engages the tine drive system when the engine speed is increased. CHOKE CONTROL ...

  • Husqvarna CT16 - page 7

    8 The operation of this tiller/cultivator can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the tiller/cultivator. We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses. CAUTION: KEEP AWAY FROM THE ROTATING PARTS. ...

  • Husqvarna CT16 - page 8

    9 GAS OIL GAS OIL 1 Gal. 5 oz. 4 Liters .167 L 2 Gal. 11 oz. 8 Liters .333 L 5 Gal. 27 oz. 20 Liters .833 L U. S. S. I. (METRIC) ● Tilt the tiller/cultivator back on the depth rod or transport wheels to raise the tines off the ground. ● Grasp the upper handle firmly to stabilize the tiller/cultivator and pull the starter handle with short quick ...

  • Husqvarna CT16 - page 9

    10 FIGURE 7 DEPTH ROD IN TILLING POSITION FIG. 2-OP TILLING HINTS ● Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. Tilling will also clear the soil of unwanted vegetation. The decomposi tion of this vegetation matter enriches the soil. De ...

  • Husqvarna CT16 - page 10

    11 GENERAL The warranty on this tiller/cultivator does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain the tiller/cultivator as instructed in this manual. The follow SERVICE DATES SCHEDULE Tighten All Screws and Nuts After first 2 Hours Every 25 Hours Ev ...

  • Husqvarna CT16 - page 11

    12 ENGINE AIR CLEANER The air cleaner filter should be cleaned and reoiled after 3 months or 25 hours of operation. Clean more often under dusty conditions. IMPORTANT: The engine can be worn out in a very short period of time if dirt or grit is allowed to enter the engine. To clean the air filter, do the following: ● Loosen screws on air cleaner ...

  • Husqvarna CT16 - page 12

    13 LEFT SIDE TINES RIGHT SIDE TINES CLEVIS PINS HAIRPINS FRONT VIEW RIGHT SIDE INDICATOR PROPERLY INSTALLED RIGHT SIDE TINES TINE REPLACEMENT The tiller/cultivator is left hand or right hand as viewed from the operator's position behind the unit. All four tines on this unit are different and cannot be inter- changed. The tines must be properly ...

  • Husqvarna CT16 - page 13

    14 CARBURETOR ADJUSTMENT A dirty air cleaner will cause the engine to run improperly and/or smoke excessively. Be sure the air cleaner is clean before adjusting the carburetor. Never make unnecessary adjustments to the carburetor. The carburetor was set at the factory to operate efficiently under most applications. How- ever, if adjustments are req ...

  • Husqvarna CT16 - page 14

    15 ● Drain the fuel from the fuel tank into an approved container outdoors, away from open flame. ● Start and run the engine until it stops due to lack of fuel. ● Pull the starter handle slowly until you feel resistance due to compression pressure, then stop. ● Release the starter tension slowly to prevent the engine from reversing due to c ...

  • Husqvarna CT16 - page 15

    16 Drain fuel tank. Fill with fresh mixture. Check fuel mix chart and mix fresh fuel. Clean fuel tank. Fuel tank should be half full when starting engine. See carburetor adjustment section. Clean and re-gap plug. Clean and re-oil air cleaner. Blow dirt and debris off top of carburetor. Clean and re-oil air cleaner. Check fuel mix chart and mix fres ...

メーカー Husqvarna カテゴリー Brush Cutter

Husqvarna CT16のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CT16の取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna CT16の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna CT16の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna CT16の取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna CT16のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna CT16の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna CT16デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna CT16を使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna CT16ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna CT16の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna CT16の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna CT16に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna CT16デバイスの基本機能を使うにあたってのヒント。 Husqvarna CT16のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna CT16に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna CT16のメーカー/サービスへの連絡先に関する情報。

Husqvarna CT16についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna CT16の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna CT16で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)