Bedienungsanleitung Ringdale IP Router

12 Seiten 0.09 mb
Download

Zur Seite of 12

Summary
  • Ringdale IP Router - page 1

    1 Contents Introduction 2 Installation 3 Using PeripheralVision ® to Configure the IP Router 5 IP Router Page 5 Passwords 6 Routing T able Page 7 Broadcast Forward Page 8 PeripheralVision ® Licensing 9 Safety and Location Advice 1 0 Troubleshooting and Technical Reference 1 1 Technical Support 1 2 ...

  • Ringdale IP Router - page 2

    2 Introduction The Ringdale IP Router is a local two port Ethernet IP router which enables IP packets to be routed from one Network/Subnet to another on your Local or Wide Area Network, and even across the Internet if required. The IP Router is simple to install and can be configured and remotely managed using the PeripheralVision ® software provi ...

  • Ringdale IP Router - page 3

    3 Installation Connect the power cord to the Power Input socket as shown in the illustration below and plug into power supply . The LEDs will flash to indicate that the device has powered up. The illustration shows the position of the ports and the diagnostic LEDs. The two ports are itemized as follows: Network 1 Port Connect to this port the RJ45 ...

  • Ringdale IP Router - page 4

    4 The LEDs are itemized as follows: Link (Y ellow) LED The Link LED indicates that the port is functionally connected to an external port. It lights up when the connected hub is turned on. If the LED does not light up, there may be a problem with the cabling or the hub. Write (Red) LED The write LED blinks when a data packet is being sent from that ...

  • Ringdale IP Router - page 5

    5 Using PeripheralVision ® to Configure the IP Router Full Installation and operational procedures for PeripheralVision ® are dealt with in the separate manual accompanying the Installation CD, refer to this if any problems are encountered in the procedure detailed below . Install PeripheralVision ® onto a PC on Network One. Using the Locate NPM ...

  • Ringdale IP Router - page 6

    6 Default Gateway IP Address Enter here the default gateway IP address for Network 1. DNS Name Server Address This information is not necessary . Local IP Address Enter here the router ’ s IP address for Network 2. Local IP Subnet Mask Enter here the subnet mask for Network 2. Click on Apply to register the new information. Passwords It is strong ...

  • Ringdale IP Router - page 7

    7 It is now necessary to tell the IP Router where to route the IP packets to. This is done by creating a Routing T able as above. Configure each route as follows. IP Address Enter here the IP Address of the subnet you want to route to. Subnet Mask Enter here the Subnet Mask of the above IP Address. Gateway Enter here the Gateway address of the abov ...

  • Ringdale IP Router - page 8

    8 Click on the Add Route button to add a new route. Click on the Edit Route button to change the configuration of an existing route. Click on the Delete Route button to remove a route. Once the routes have been set up as required, click on Apply . The Ringdale IP Router is now configured and will route your IP packets automatically as specified. Br ...

  • Ringdale IP Router - page 9

    9 T o forward a broadcast through the router to the required IP address click on Add . This will open the window below: Enter the IP address and click on OK . The IP address will be entered into the list. T o make changes to an IP address already on the list, click on the required address to select it and then click on Edit . This will open the abo ...

  • Ringdale IP Router - page 10

    10 The device is designed to operate in a typical office environment. Choose a site that is: Well ventilated and away from sources of heat including direct sunlight. Away from sources of vibration or physical shock. Isolated from strong electromagnetic fields produced by electrical devices. Provided with a properly grounded wall outlet. Do not atte ...

  • Ringdale IP Router - page 11

    11 Troubleshooting and Technical Reference Symptom Poss. Cause Action LEDs do not flash Power switched off Switch on at power-up Power cord not connected Plug in Router Fuse defect Replace fuse Link LED does No cable inserted Connect to hub not light up and Router Router not Check power supply powered up for Router Wrong cable type V erify cable se ...

  • Ringdale IP Router - page 12

    12 Technical Support Ringdale Ltd, Ringdale Inc. and Ringdale GmbH all have T echnical Support Departments. Their addresses and contact details are found on the back cover of this manual. Before you call: Please have the following information ready before calling: T ype of adapters installed in the System. The adapter settings and interrupt options ...

Produzent Ringdale Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Ringdale IP Router erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Ringdale
- Bedienungsanleitungen IP Router
- Produktkarten Ringdale
- Informationsbroschüren
- oder Energieetiketten Ringdale IP Router
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Ringdale IP Router.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Ringdale IP Router, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Ringdale IP Router. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Ringdale IP Router ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Ringdale IP Router, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Ringdale IP Router hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Ringdale IP Router verständlich ist.

Eine gänzliche Bedienungsanleitung von Ringdale sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Ringdale IP Router bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Ringdale IP Router befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Ringdale IP Router, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Ringdale IP Router - die uns die ersten Schritte während der Nutzung von Ringdale IP Router erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Ringdale IP Router hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Ringdale IP Router im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Ringdale IP Router?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ringdale IP Router nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ringdale IP Router hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)