Manuale per l’uso Ringdale IP Router

12 pagine 0.09 mb
Scarica

Vai alla pagina of 12

Summary
  • Ringdale IP Router - page 1

    1 Contents Introduction 2 Installation 3 Using PeripheralVision ® to Configure the IP Router 5 IP Router Page 5 Passwords 6 Routing T able Page 7 Broadcast Forward Page 8 PeripheralVision ® Licensing 9 Safety and Location Advice 1 0 Troubleshooting and Technical Reference 1 1 Technical Support 1 2 ...

  • Ringdale IP Router - page 2

    2 Introduction The Ringdale IP Router is a local two port Ethernet IP router which enables IP packets to be routed from one Network/Subnet to another on your Local or Wide Area Network, and even across the Internet if required. The IP Router is simple to install and can be configured and remotely managed using the PeripheralVision ® software provi ...

  • Ringdale IP Router - page 3

    3 Installation Connect the power cord to the Power Input socket as shown in the illustration below and plug into power supply . The LEDs will flash to indicate that the device has powered up. The illustration shows the position of the ports and the diagnostic LEDs. The two ports are itemized as follows: Network 1 Port Connect to this port the RJ45 ...

  • Ringdale IP Router - page 4

    4 The LEDs are itemized as follows: Link (Y ellow) LED The Link LED indicates that the port is functionally connected to an external port. It lights up when the connected hub is turned on. If the LED does not light up, there may be a problem with the cabling or the hub. Write (Red) LED The write LED blinks when a data packet is being sent from that ...

  • Ringdale IP Router - page 5

    5 Using PeripheralVision ® to Configure the IP Router Full Installation and operational procedures for PeripheralVision ® are dealt with in the separate manual accompanying the Installation CD, refer to this if any problems are encountered in the procedure detailed below . Install PeripheralVision ® onto a PC on Network One. Using the Locate NPM ...

  • Ringdale IP Router - page 6

    6 Default Gateway IP Address Enter here the default gateway IP address for Network 1. DNS Name Server Address This information is not necessary . Local IP Address Enter here the router ’ s IP address for Network 2. Local IP Subnet Mask Enter here the subnet mask for Network 2. Click on Apply to register the new information. Passwords It is strong ...

  • Ringdale IP Router - page 7

    7 It is now necessary to tell the IP Router where to route the IP packets to. This is done by creating a Routing T able as above. Configure each route as follows. IP Address Enter here the IP Address of the subnet you want to route to. Subnet Mask Enter here the Subnet Mask of the above IP Address. Gateway Enter here the Gateway address of the abov ...

  • Ringdale IP Router - page 8

    8 Click on the Add Route button to add a new route. Click on the Edit Route button to change the configuration of an existing route. Click on the Delete Route button to remove a route. Once the routes have been set up as required, click on Apply . The Ringdale IP Router is now configured and will route your IP packets automatically as specified. Br ...

  • Ringdale IP Router - page 9

    9 T o forward a broadcast through the router to the required IP address click on Add . This will open the window below: Enter the IP address and click on OK . The IP address will be entered into the list. T o make changes to an IP address already on the list, click on the required address to select it and then click on Edit . This will open the abo ...

  • Ringdale IP Router - page 10

    10 The device is designed to operate in a typical office environment. Choose a site that is: Well ventilated and away from sources of heat including direct sunlight. Away from sources of vibration or physical shock. Isolated from strong electromagnetic fields produced by electrical devices. Provided with a properly grounded wall outlet. Do not atte ...

  • Ringdale IP Router - page 11

    11 Troubleshooting and Technical Reference Symptom Poss. Cause Action LEDs do not flash Power switched off Switch on at power-up Power cord not connected Plug in Router Fuse defect Replace fuse Link LED does No cable inserted Connect to hub not light up and Router Router not Check power supply powered up for Router Wrong cable type V erify cable se ...

  • Ringdale IP Router - page 12

    12 Technical Support Ringdale Ltd, Ringdale Inc. and Ringdale GmbH all have T echnical Support Departments. Their addresses and contact details are found on the back cover of this manual. Before you call: Please have the following information ready before calling: T ype of adapters installed in the System. The adapter settings and interrupt options ...

Fabbricante Ringdale Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoRingdale IP Router possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Ringdale
- manuali per l’uso IP Router
- schede prodotto Ringdale
- opuscoli
- o etichette energetiche Ringdale IP Router
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Ringdale IP Router.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Ringdale IP Router, manuali di manutenzione, brevi manuali o manuali utente Ringdale IP Router. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Ringdale IP Router.

Manuali per l’uso simili

Manuale completo del dispositivo Ringdale IP Router, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Ringdale IP Router dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Ringdale IP Router.

Il manuale per l’uso completo Ringdale, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Ringdale IP Router - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Ringdale IP Router, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Ringdale IP Router che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Ringdale IP Router - che ci dovrebbe aiutare nei primi passi durante l'uso Ringdale IP Router
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Ringdale IP Router
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Ringdale IP Router in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Ringdale IP Router?

Utilizza il modulo sottostante

Se non hai risolto il problema con Ringdale IP Router con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Ringdale IP Router è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)