Bedienungsanleitung Cisco Systems 7304

22 Seiten 0.26 mb
Download

Zur Seite of 22

Summary
  • Cisco Systems 7304 - page 1

    CHAPTER 13-1 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 13 Configuring the 2-Port and 4-Port T3/E3 SPAs This chapter provides information about conf iguring the 2-Port and 4-Port T3/E3 Shared Port Adapters (SP As) on the Cisco 7304 router. It includes the following sections: • Conf igur ...

  • Cisco Systems 7304 - page 2

    13-2 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Required Configuration Tasks This section lists the required conf iguration steps to conf igure the 2-Port or 4-Port T3/E3 SP A. Some of the required conf iguration ...

  • Cisco Systems 7304 - page 3

    13-3 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configure the Interface T o set the ip address for the 2-Port or 4-Port T3/E3 SP A, complete these steps: Verifying Controller Configuration Use the show controllers ...

  • Cisco Systems 7304 - page 4

    13-4 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks 0 C-bit Coding Violation, 0 P-bit Err Secs, 0 P-bit Sev Err Secs, 0 Sev Err Framing Secs, 0 Unavailable Secs, 24750 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit ...

  • Cisco Systems 7304 - page 5

    13-5 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Serial6/0/0.16 is up, line protocol is up Hardware is SPA-4T3E3 Internet address is 110.1.1.2/24 MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec, reliability 255/255, tx ...

  • Cisco Systems 7304 - page 6

    13-6 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Data Service Unit Mode Conf igure the SP A to connect with customer premise Data Service Units (DSUs) by setting the DSU mode. Subrating a T3 or E3 inter ...

  • Cisco Systems 7304 - page 7

    13-7 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verifying DSU Mode Use the show controllers serial command to display the DSU settings: router# show controllers serial 6/0/0 Serial6/0/0 - Framing is c-bit, Clock S ...

  • Cisco Systems 7304 - page 8

    13-8 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks 0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs Data in Interval 1: 0 Line Code Violations, 0 P-bit Coding Violation 0 C-bit Coding Violation 0 P-bit ...

  • Cisco Systems 7304 - page 9

    13-9 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Router(conf ig-if)# mdl [ string { eic | f ic | generator | lic | pf i | port | unit } string }] | [ transmit { idle-signal | path | test-signal }] Conf igures the M ...

  • Cisco Systems 7304 - page 10

    13-10 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verifying MDL Use the show controllers serial command to display the MDL settings: router# show controllers serial 6/0/0 Serial6/0/0 - Framing is c-bit, Clock Sourc ...

  • Cisco Systems 7304 - page 11

    13-11 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Scrambling can pre vent some bit patterns from being mistakenly interpreted as alarms by switches placed between the Data Service Units (DSUs). T o conf igure scram ...

  • Cisco Systems 7304 - page 12

    13-12 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Framing Framing is used to synchronize data transmission on the line. Framing allo ws the hardware to determine when each packet starts and ends. T o co ...

  • Cisco Systems 7304 - page 13

    13-13 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Encapsulation When traff ic crosses a W AN link, the connection needs a Layer 2 protocol to encapsulate traf f ic. T o set the encapsulation method, use ...

  • Cisco Systems 7304 - page 14

    13-14 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Cable Length The cablelength command compensates for the loss in decibels based on the distance from the device to the f irst repeater in the circuit. A ...

  • Cisco Systems 7304 - page 15

    13-15 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Configuring Invert Data Delays between the TE clock and data transmission indicate that the transmit clock signal might not be appropriate for the interface rate an ...

  • Cisco Systems 7304 - page 16

    13-16 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Tasks Verify TTB Settings Use the show controllers serial command to display the TTB settings for the interface: router# show controllers serial 6/0/0 Serial6/0/0 - Frami ...

  • Cisco Systems 7304 - page 17

    13-17 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Verifying the Interface Configuration Saving the Configuration T o sa ve your running conf iguration to nonv olatile random-access memory (NVRAM), use the following command in pri vile ...

  • Cisco Systems 7304 - page 18

    13-18 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Verifying the Interface Configuration Monitoring Per-Port Interface Statistics T o f ind detailed status and statistical information on a per-port basis for the 2-Port or 4-Port T3/E3 ...

  • Cisco Systems 7304 - page 19

    13-19 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples No FEAC code is being received MDL transmission is disabled Configuration Examples This section includes the following conf iguration examples: • DSU Conf igur ...

  • Cisco Systems 7304 - page 20

    13-20 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples Router(config-if)# mdl transmit path Router(config-if)# mdl transmit idle-signal Router(config-if)# mdl transmit test-signal Scrambling Configuration Example The ...

  • Cisco Systems 7304 - page 21

    13-21 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples ! Specify the cable length ! Router(config-if)# cablelength 200 Invert Data Configuration Example The following e xample enables in vert data: ! Enter global con ...

  • Cisco Systems 7304 - page 22

    13-22 Cisco 7304 Router Modular Services Card and Shared Port Adapter Software Configuration Guide OL-4807-02 Chapter 13 Configuring the 2-Port and 4-Port T3/E3 SPAs Configuration Examples ...

Produzent Cisco Systems Kategorie Network Router

Dokumente, die wir vom Produzenten des Geräts Cisco Systems 7304 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco Systems
- Bedienungsanleitungen 7304
- Produktkarten Cisco Systems
- Informationsbroschüren
- oder Energieetiketten Cisco Systems 7304
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Systems 7304.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Systems 7304, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Systems 7304. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Systems 7304 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Systems 7304, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Systems 7304 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Systems 7304 verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco Systems sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Systems 7304 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Systems 7304 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Systems 7304, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Systems 7304 - die uns die ersten Schritte während der Nutzung von Cisco Systems 7304 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Systems 7304 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Systems 7304 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Systems 7304?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Systems 7304 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Systems 7304 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)