Bedienungsanleitung Harbor Freight Tools 34202

14 Seiten 0.65 mb
Download

Zur Seite of 14

Summary
  • Harbor Freight Tools 34202 - page 1

    40 LB. PRESSURIZED SANDBL ASTER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 Copyright © 1997 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools. For t ...

  • Harbor Freight Tools 34202 - page 2

    SPECIFICA TIONS Capacity: 40 lbs. Working Pressure 60-125 PSI Delivery Rate 6-25 CFM Overall Dimensions 33.5" x 18.75" x 13" Weight: 57 lbs. SA VE THIS MANUAL Y ou will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. ...

  • Harbor Freight Tools 34202 - page 3

    9. DO NOT ABUSE THE POWER CORD. Do not yank compressor ’s cord to disconnect it from the receptacle. Do not carry tools by the cord. 10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines. 11 . MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow i ...

  • Harbor Freight Tools 34202 - page 4

    22. MAINT AIN CORRECT AIR PRESSURE WHENEVER WORKING . Do not allow pressure to exceed 125 PSI. If the safety valve does not release excess air pressure, stop all work and use the air compressor to release pressure in the tank. Do not attempt any repairs to the Sandblaster until its gauge reads “0”. AIR/SAND SUPPL Y REQUIREMENTS Hose Hose Nozzle ...

  • Harbor Freight Tools 34202 - page 5

    ASSEMBL Y NOTE: Use T eflon® Pipe T ape on all threaded joints. Make sure all joints are securely tighten. Intake Manifold Refer to Figure 1. S tep1: Get out the INT AKE MANIFOLD (#14), PRESSURE GAUGE (#15), BRASS THROTTLING V AL VE (#18A), 3/8" 1/4" NIPPLE CONNECTOR (#20), and JOINT PIPE (#13). S tep2: Attach the PRESSURE GAUGE to the t ...

  • Harbor Freight Tools 34202 - page 6

    Water Trap Refer to Figure 2. Figure 2 — Water Trap Assembly S tep1: Get out the WA TER TRAP (#17), two 3/8" NIPPLE CONNECTORS (#16), the BRASS AIR SUPPL Y V AL VE (#18), and the MALE/FEMALE ADAPTER (#19). S tep2: A tt ach the 3/8" NIPPLE CONNECTORS to either side of the W A TER TRAP . S tep3: On the top of the WA TER TRAP is an arrow . ...

  • Harbor Freight Tools 34202 - page 7

    Nozzle Shut Off V alve Refer to Figure 4. S tep1: Get out the HOSE ADAPTER (#25), the STEEL SHUT OFF V AL VE (#18C), a NIPPLE CONNECTOR (#16), the GASKET (#26), the desired size NOZZLE (#27A-D), and the NOZZLE CAP NUT (#28). S tep2: Put the front of the NOZZLE through the NOZZLE CAP NUT . S tep3: Attach the NOZZLE CAP NUT to the NIPPLE CONNECTOR wi ...

  • Harbor Freight Tools 34202 - page 8

    S tep5: At t ach the HOSE ADAPTER to the other end of the STEEL SHUT OFF V AL VE. Sand Control V alve/ Nozzle Shut Off V alve Refer to Figure 5. Sand Con trol V alve Assem bly Sand Hose Nozzle Shut O ff V alve Asse m bly Hose Clamp (# 23) Figure 5 — Sand Control V alve / Shut Off V alve Assembly S tep1: Get out the Sand Control V alve & Nozzl ...

  • Harbor Freight Tools 34202 - page 9

    T op Assembly Refer to Figure 6. T ank (# 1) Ni pple Connector (# 16) Ni pple Connector (# 16) Air Hos e (# 21) Gasket (# 1 1) Air Ca p (# 12) Joint P ipe (# 13) Figure 6 — T op Assembly S tep1: Get the Int ake V alve Assembly , the W ater Trap Assembly , the T ank Assembly , the T ANK CAP (#12), the O-RING (#1 1), and the AIR HOSE (#21). S tep2: ...

  • Harbor Freight Tools 34202 - page 10

    Handle Bars Refer to Figure 7. Handl e Grip (# 7) Handl e B ar (# 6) Scre w (# 8) W asher (# 31) Nut (# 9) Figure 7 — Handle Bar Assembly S tep1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four W ASHERS (#31). S tep2: Sl ide the HANDLE GRIPS onto the HANDLE BARS. S tep3: A tt ach both HA ...

  • Harbor Freight Tools 34202 - page 11

    Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment S tep 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). S tep 2: Attach the FOOT to the T ANK (#1) using one of the COTTER PINS. S tep 3: Attach one of the WHEELS to the AXLE using one of the COTTER PINS. S tep 4: Slide the AX ...

  • Harbor Freight Tools 34202 - page 12

    OPERA TIONS Loading Abrasives S tep 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. S tep 2: Close the AIR SUPPL Y V AL VE (#18) by turning it to the horizontal position. S tep 3: Open the NOZZLE SHUT OFF V AL VE (#18C) by turning it to the vertical position. S tep 4: Make sure the PRESSURE GAUGE (#15) reads ? ...

  • Harbor Freight Tools 34202 - page 13

    Item# Description Q ty Item# Description Q ty 1 T a nk 1 18B 3/8" S teel Sand Control V alve 1 2 Wheel 2 18C 3/8" S teel Shut Off V alve 1 3 Cotter Pin 3 1 9 Male/Female Adapter 1 4 Foot 1 20 3/8" 1/4" Nipple Connector 1 5 Axle 1 21 Air Hose 1 6 * Handle Bar 2 22 Sand Outlet Manifold 1 7 Handle Grip 2 23 Hose Clamp 2 8 Pan Screw ...

  • Harbor Freight Tools 34202 - page 14

    19 16 16 17 15 14 18A 20 18 13 7 8 9 3 5 21 14 2 1 24 23 28 27A-D 26 16 18C 25 16 18B 16 22 23 31 12 11 10 6 3 P ARTS DRA WING Page #14 -- SKU 34202 ...

Produzent Harbor Freight Tools Kategorie Sander

Dokumente, die wir vom Produzenten des Geräts Harbor Freight Tools 34202 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Harbor Freight Tools
- Bedienungsanleitungen 34202
- Produktkarten Harbor Freight Tools
- Informationsbroschüren
- oder Energieetiketten Harbor Freight Tools 34202
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Harbor Freight Tools 34202.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Harbor Freight Tools 34202, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Harbor Freight Tools 34202. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Harbor Freight Tools 34202 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Harbor Freight Tools 34202, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Harbor Freight Tools 34202 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Harbor Freight Tools 34202 verständlich ist.

Eine gänzliche Bedienungsanleitung von Harbor Freight Tools sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Harbor Freight Tools 34202 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Harbor Freight Tools 34202 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Harbor Freight Tools 34202, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Harbor Freight Tools 34202 - die uns die ersten Schritte während der Nutzung von Harbor Freight Tools 34202 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Harbor Freight Tools 34202 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Harbor Freight Tools 34202 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Harbor Freight Tools 34202?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Harbor Freight Tools 34202 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Harbor Freight Tools 34202 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)