Manuel d’utilisation Harbor Freight Tools 34202

14 pages 0.65 mb
Télécharger

Aller à la page of 14

Summary
  • Harbor Freight Tools 34202 - page 1

    40 LB. PRESSURIZED SANDBL ASTER ASSEMBL Y and OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 9301 1 Copyright © 1997 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight T ools. For t ...

  • Harbor Freight Tools 34202 - page 2

    SPECIFICA TIONS Capacity: 40 lbs. Working Pressure 60-125 PSI Delivery Rate 6-25 CFM Overall Dimensions 33.5" x 18.75" x 13" Weight: 57 lbs. SA VE THIS MANUAL Y ou will need the manual for the safety warnings and cautions, assembly instructions, operating procedures, maintenance procedures, trouble shooting, parts list, and diagram. ...

  • Harbor Freight Tools 34202 - page 3

    9. DO NOT ABUSE THE POWER CORD. Do not yank compressor ’s cord to disconnect it from the receptacle. Do not carry tools by the cord. 10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or across running machines. 11 . MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow i ...

  • Harbor Freight Tools 34202 - page 4

    22. MAINT AIN CORRECT AIR PRESSURE WHENEVER WORKING . Do not allow pressure to exceed 125 PSI. If the safety valve does not release excess air pressure, stop all work and use the air compressor to release pressure in the tank. Do not attempt any repairs to the Sandblaster until its gauge reads “0”. AIR/SAND SUPPL Y REQUIREMENTS Hose Hose Nozzle ...

  • Harbor Freight Tools 34202 - page 5

    ASSEMBL Y NOTE: Use T eflon® Pipe T ape on all threaded joints. Make sure all joints are securely tighten. Intake Manifold Refer to Figure 1. S tep1: Get out the INT AKE MANIFOLD (#14), PRESSURE GAUGE (#15), BRASS THROTTLING V AL VE (#18A), 3/8" 1/4" NIPPLE CONNECTOR (#20), and JOINT PIPE (#13). S tep2: Attach the PRESSURE GAUGE to the t ...

  • Harbor Freight Tools 34202 - page 6

    Water Trap Refer to Figure 2. Figure 2 — Water Trap Assembly S tep1: Get out the WA TER TRAP (#17), two 3/8" NIPPLE CONNECTORS (#16), the BRASS AIR SUPPL Y V AL VE (#18), and the MALE/FEMALE ADAPTER (#19). S tep2: A tt ach the 3/8" NIPPLE CONNECTORS to either side of the W A TER TRAP . S tep3: On the top of the WA TER TRAP is an arrow . ...

  • Harbor Freight Tools 34202 - page 7

    Nozzle Shut Off V alve Refer to Figure 4. S tep1: Get out the HOSE ADAPTER (#25), the STEEL SHUT OFF V AL VE (#18C), a NIPPLE CONNECTOR (#16), the GASKET (#26), the desired size NOZZLE (#27A-D), and the NOZZLE CAP NUT (#28). S tep2: Put the front of the NOZZLE through the NOZZLE CAP NUT . S tep3: Attach the NOZZLE CAP NUT to the NIPPLE CONNECTOR wi ...

  • Harbor Freight Tools 34202 - page 8

    S tep5: At t ach the HOSE ADAPTER to the other end of the STEEL SHUT OFF V AL VE. Sand Control V alve/ Nozzle Shut Off V alve Refer to Figure 5. Sand Con trol V alve Assem bly Sand Hose Nozzle Shut O ff V alve Asse m bly Hose Clamp (# 23) Figure 5 — Sand Control V alve / Shut Off V alve Assembly S tep1: Get out the Sand Control V alve & Nozzl ...

  • Harbor Freight Tools 34202 - page 9

    T op Assembly Refer to Figure 6. T ank (# 1) Ni pple Connector (# 16) Ni pple Connector (# 16) Air Hos e (# 21) Gasket (# 1 1) Air Ca p (# 12) Joint P ipe (# 13) Figure 6 — T op Assembly S tep1: Get the Int ake V alve Assembly , the W ater Trap Assembly , the T ank Assembly , the T ANK CAP (#12), the O-RING (#1 1), and the AIR HOSE (#21). S tep2: ...

  • Harbor Freight Tools 34202 - page 10

    Handle Bars Refer to Figure 7. Handl e Grip (# 7) Handl e B ar (# 6) Scre w (# 8) W asher (# 31) Nut (# 9) Figure 7 — Handle Bar Assembly S tep1: Get out the two HANDLE BARS (#6), the two HANDLE GRIPS (#5), the four SCREWS (#8), four NUTS (#9), and four W ASHERS (#31). S tep2: Sl ide the HANDLE GRIPS onto the HANDLE BARS. S tep3: A tt ach both HA ...

  • Harbor Freight Tools 34202 - page 11

    Wheels and Foot See Figure 8. 5 3 2 4 3 3 2 Figure 8 - Wheel and Foot Attachment S tep 1: Get out the two WHEELS (#2), the three COTTER PINS (#3), the FOOT (#4) and the AXLE (#5). S tep 2: Attach the FOOT to the T ANK (#1) using one of the COTTER PINS. S tep 3: Attach one of the WHEELS to the AXLE using one of the COTTER PINS. S tep 4: Slide the AX ...

  • Harbor Freight Tools 34202 - page 12

    OPERA TIONS Loading Abrasives S tep 1: Check to insure the abrasives are dry and clean so that they do not clog the unit. S tep 2: Close the AIR SUPPL Y V AL VE (#18) by turning it to the horizontal position. S tep 3: Open the NOZZLE SHUT OFF V AL VE (#18C) by turning it to the vertical position. S tep 4: Make sure the PRESSURE GAUGE (#15) reads ? ...

  • Harbor Freight Tools 34202 - page 13

    Item# Description Q ty Item# Description Q ty 1 T a nk 1 18B 3/8" S teel Sand Control V alve 1 2 Wheel 2 18C 3/8" S teel Shut Off V alve 1 3 Cotter Pin 3 1 9 Male/Female Adapter 1 4 Foot 1 20 3/8" 1/4" Nipple Connector 1 5 Axle 1 21 Air Hose 1 6 * Handle Bar 2 22 Sand Outlet Manifold 1 7 Handle Grip 2 23 Hose Clamp 2 8 Pan Screw ...

  • Harbor Freight Tools 34202 - page 14

    19 16 16 17 15 14 18A 20 18 13 7 8 9 3 5 21 14 2 1 24 23 28 27A-D 26 16 18C 25 16 18B 16 22 23 31 12 11 10 6 3 P ARTS DRA WING Page #14 -- SKU 34202 ...

Fabricant Harbor Freight Tools Catégorie Sander

Les documents que nous recevons du fabricant de l'appareilHarbor Freight Tools 34202 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Harbor Freight Tools
- manuels d’utilisations 34202
- fiches produit Harbor Freight Tools
- dépliants
- ou étiquettes-énergie Harbor Freight Tools 34202
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Harbor Freight Tools 34202.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Harbor Freight Tools 34202, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Harbor Freight Tools 34202. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Harbor Freight Tools 34202.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Harbor Freight Tools 34202, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Harbor Freight Tools 34202 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Harbor Freight Tools 34202.

Le manuel d’utilisation complet Harbor Freight Tools, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Harbor Freight Tools 34202 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Harbor Freight Tools 34202, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHarbor Freight Tools 34202 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Harbor Freight Tools 34202 - qui devraient nous aider dans les premières étapes lors de l'utilisation Harbor Freight Tools 34202
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Harbor Freight Tools 34202
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Harbor Freight Tools 34202 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Harbor Freight Tools 34202?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Harbor Freight Tools 34202, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Harbor Freight Tools 34202 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)