Bedienungsanleitung Vector VEC093

12 Seiten 0.23 mb
Download

Zur Seite of 12

Summary
  • Vector VEC093 - page 1

    1 AUTOMA TIC BA TTER Y CHARGER OWNER’S MANUAL & W ARRANTY INFORMA TION 12 VOL T 2/1 0/20/40 AMPERE CHARGE RA TES WITH 1 00 AMP ENGINE ST AR T , AL TERNA TOR VOL T AGE CHECK AND BA TTERY RECONDITON FUNCTIONS • IMPORT ANT SAFETY INSTRUCTIONS • W ARNING – RISK OF EXPLOSIVE GASES 1. WORKING IN VICINITY OF A LEAD-ACID BA TTER Y IS DANGEROUS. ...

  • Vector VEC093 - page 2

    2 PERSONAL PRECAUTIONS AND SAFETY 1. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid batter y . 2. Have plenty of fresh water and soap nearby in case batter y acid contacts skin, clothing, or eyes. 3. W ear complete eye protection and clothing protection. Avoid touching eyes while work ...

  • Vector VEC093 - page 3

    3 PREP ARING TO CHARGE 1. Determine voltage of batter y by referring to car owner's manual. 2. If it is necessar y to remove batter y from vehicle to charge, or to clean terminals, always remove grounded terminal from batter y first. Make sure all accessories in the vehicle are off, so as not to cause an arc. 3. Clean batter y ter minals. Be c ...

  • Vector VEC093 - page 4

    4 INTRODUCTION AND FEA TURES Thank you for selecting the V ector(r) Model VEC093 2/1 0/20/40 Amp 12 volt Smart Batter y Charger with Engine Start, Alter nator V oltge Check and Batter y Restore modes. With proper care and use, it will give you years of depend- able ser vice. This model batter y charger has a high charge rate of up to 40 amps, and l ...

  • Vector VEC093 - page 5

    5 FIGURE 3A (FRONT VIEW) FIGURE 3B (REAR VIEW) W ARNINGS: • THERE ARE NO USER-SERVICEABLE P AR TS IN THIS UNIT . IN THE EVENT OF ANY OPERA TING PROBLEM THA T THE UNIT'S BUIL T -IN CIRCUIT PROTECTION CAN NOT HANDLE. • DO NOT OPEN THE UNIT . IT MUST BE RETURNED TO VECTOR FOR PROFESSIONAL TESTING AND REP AIR. OPENING THE UNIT WILL VOID THE MA ...

  • Vector VEC093 - page 6

    6 INDICA TORS THE LARGE 3-CHARACTER DIGIT AL DISPLA Y in the upper left hand corner of the panel indicates many conditions. It indicates when AC power is applied to the charger , actual charge rate in amperes, when the batter y is fully charged, detected faults, operating modes and when the charger is ready for the next mode selection. What is disp ...

  • Vector VEC093 - page 7

    7 CHARGE RA TE SELECTION VEC093 After the clamps are connected, plug in the charger to an AC outlet and the charger will show a circulating pattern on the Digital Display . This pattern indicates power is applied. Press the ON/OFF button to prepare the charger to change to an operating mode. Press the 2/1 0/20/40 A button and the charger will begin ...

  • Vector VEC093 - page 8

    8 CONNECTING IF BA TTER Y IS OUTSIDE OF VEHICLE a) Check polarity of batter y posts- For top-mounted batter y connectors, the positive post (marked POS, P , +) usually has a larger diameter than the Negative batter y post (marked NEG, N, –). For side-mounted batter y connections the Positive terminal is red, the Negative terminal is black. b) Att ...

  • Vector VEC093 - page 9

    9 This slowly (over 24 hours) removes the insulating buildup from the plates so the batter y can hold a full charge. Most automotive batteries (50 to 70AH) can be treated once to reduce the lead sulfate buildup. Smaller 12 volt batteries, such as found in jump starters can be treated for 12 hours. However , depending on the severity of lead sulfate ...

  • Vector VEC093 - page 10

    10 TROUBLESHOOTING - F AUL T LED LIT NOTE: Batteries below 4.0 V olts will not allow the charger to operate. Make sure the batter y has at least 4 V olts if charger will not charge. The following conditions may light the F AULT LED: • Poor connection to the batter y (or frame). • Charging too fast - Decrease Charge Rate - Press 2/1 0/20/40A Pus ...

  • Vector VEC093 - page 11

    11 APPENDIX A — CHARGING TIMES To calculate the approximate charging time required to fully charge a batter y , it is necessar y to determine the specific gravity (or , percent of batter y charge) using a hydrometer . Use this technique if batter y vent caps can be removed. Check each cell. If there is one cell with a ver y low specific gravity c ...

  • Vector VEC093 - page 12

    12 VECTOR 5 YEAR LIMITED W ARRANTY PROGRAM This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of V ector Manufacturing, Ltd., regarding this product. There is no other warranty , other than described herein. This V ector Manufacturing, Ltd. product is warranted, to the original pur ...

Produzent Vector Kategorie Automobile Battery Charger

Dokumente, die wir vom Produzenten des Geräts Vector VEC093 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Vector
- Bedienungsanleitungen VEC093
- Produktkarten Vector
- Informationsbroschüren
- oder Energieetiketten Vector VEC093
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Vector VEC093.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Vector VEC093, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Vector VEC093. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Vector VEC093 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Vector VEC093, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Vector VEC093 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Vector VEC093 verständlich ist.

Eine gänzliche Bedienungsanleitung von Vector sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Vector VEC093 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Vector VEC093 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Vector VEC093, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Vector VEC093 - die uns die ersten Schritte während der Nutzung von Vector VEC093 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Vector VEC093 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Vector VEC093 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Vector VEC093?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Vector VEC093 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Vector VEC093 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (1)

Jose Antonio

Al intentar scanear me dice que conecte el scaner. Una y otra vez.