Bedienungsanleitung Zenoah G3801EZ

15 Seiten 0.96 mb
Download

Zur Seite of 15

Summary
  • Zenoah G3801EZ - page 1

    G3801/G3801EZ G B GB-1 G3801 G3801EZ OWNER’S MANUAL CHAIN SA W G B Or iginal Language 1 15 39 06-38 (007) ...

  • Zenoah G3801EZ - page 2

    G3801/G3801EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Contents 1. For Safe Operation ................................................................... 3 2. Explanation of Symbols on the Machine .................................. 5 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Chain Oil ... ...

  • Zenoah G3801EZ - page 3

    G3801/G3801EZ G B GB-3 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy , or if you are under th ...

  • Zenoah G3801EZ - page 4

    G3801/G3801EZ GB-4 (1) cover (2) guide bar (3) saw chain (4) nut 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building and potentially explosive at- mosphere. Exhaust fumes contain dangerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so ...

  • Zenoah G3801EZ - page 5

    G3801/G3801EZ G B GB-5 2. Explanation of Symbols on the Machine The port to fuel “MIX GASOLINE” Position: Beside Fuel cap The port to fill with chain oil Position: Beside Oil cap Setting the switch to the “O” position, the engine stops immediately . Position: Beside rocker switch Starting the engine. If you pull out the choke knob (at the b ...

  • Zenoah G3801EZ - page 6

    G3801/G3801EZ GB-6 3. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 4. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. 5. Tighten the nuts securely with the bar tip held up (12 ~ 15 N·m). Then check the ch ...

  • Zenoah G3801EZ - page 7

    G3801/G3801EZ G B GB-7 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refuel- ing the unit. Select outdoor bare ground for fuel- ing and move at least 3 m (10 ft) away from the fueling point before starting the en ...

  • Zenoah G3801EZ - page 8

    G3801/G3801EZ GB-8 6. When engine has ignited, first push in the choke knob to “ST AR T” position and then pull the starter again to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly . At once pulling throttle lever out, the choke knob is automatically returned to the “RUN” position. Keep clear of the ...

  • Zenoah G3801EZ - page 9

    G3801/G3801EZ G B GB-9 1. Stop engine and screw L needle until it stops. Never force. Then set it back the initial number of turns as shown below . H needle is r estricted within the num- ber of turn as shown below . H needle : 1 3 / 8 ± 1 / 4 L needle : 1 1 / 4 ± 1 / 4 2. Start the engine and allow it to war m up in low speed for a few minutes. ...

  • Zenoah G3801EZ - page 10

    G3801/G3801EZ GB-10 A log lying on the ground Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-thir d and finish by sawing down from the top. In ar ea B, saw down fr om the top one-third and finish by sawing up fr om the bot- tom. 6. Sawing • Before proce ...

  • Zenoah G3801EZ - page 11

    G3801/G3801EZ G B GB-11 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. ■ MAINTENANCE AFTER EACH USE 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. T o clean dirt in ...

  • Zenoah G3801EZ - page 12

    G3801/G3801EZ GB-12 4. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 5. Sprocket Check for cracks and for excessive wear interfering with the chain drive. If the wear is considerable, replace it with new one. Never fit a new chain on a worn sprocket, or a worn chain on a new sprocket. Place the file ...

  • Zenoah G3801EZ - page 13

    G3801/G3801EZ G B GB-13 W ARNING: This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Saw Model Chain T ype Guide Bar Saw Chain G3801/G3801EZ 91VG 3608-52112 2932-52210 G3801/G3801EZ 95VP 2939-52110 2939-52210 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, th ...

  • Zenoah G3801EZ - page 14

    G3801/G3801EZ GB-14 11. Specifications POWER UNIT : Displacement (cm 3 ): ................................................................................. 37.2 Fuel: ..................................................................................................... Mixture when using ZENOAH genuine oil (FC grade) ................................ ...

  • Zenoah G3801EZ - page 15

    G3801/G3801EZ G B GB-15 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty period, the failed part will be replaced or repair ed fr ee of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: Six (6) months after pur chased by end-user subject to 12 months from pr oduced mon ...

Produzent Zenoah Kategorie Chainsaw

Dokumente, die wir vom Produzenten des Geräts Zenoah G3801EZ erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zenoah
- Bedienungsanleitungen G3801EZ
- Produktkarten Zenoah
- Informationsbroschüren
- oder Energieetiketten Zenoah G3801EZ
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zenoah G3801EZ.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zenoah G3801EZ, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zenoah G3801EZ. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zenoah G3801EZ ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zenoah G3801EZ, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zenoah G3801EZ hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zenoah G3801EZ verständlich ist.

Eine gänzliche Bedienungsanleitung von Zenoah sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zenoah G3801EZ bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zenoah G3801EZ befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zenoah G3801EZ, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zenoah G3801EZ - die uns die ersten Schritte während der Nutzung von Zenoah G3801EZ erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zenoah G3801EZ hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zenoah G3801EZ im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zenoah G3801EZ?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zenoah G3801EZ nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zenoah G3801EZ hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)