Zenoah G3801EZの取扱説明書

15ページ 0.96 mb
ダウンロード

ページに移動 of 15

Summary
  • Zenoah G3801EZ - page 1

    G3801/G3801EZ G B GB-1 G3801 G3801EZ OWNER’S MANUAL CHAIN SA W G B Or iginal Language 1 15 39 06-38 (007) ...

  • Zenoah G3801EZ - page 2

    G3801/G3801EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Contents 1. For Safe Operation ................................................................... 3 2. Explanation of Symbols on the Machine .................................. 5 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Chain Oil ... ...

  • Zenoah G3801EZ - page 3

    G3801/G3801EZ G B GB-3 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees. 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy , or if you are under th ...

  • Zenoah G3801EZ - page 4

    G3801/G3801EZ GB-4 (1) cover (2) guide bar (3) saw chain (4) nut 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building and potentially explosive at- mosphere. Exhaust fumes contain dangerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so ...

  • Zenoah G3801EZ - page 5

    G3801/G3801EZ G B GB-5 2. Explanation of Symbols on the Machine The port to fuel “MIX GASOLINE” Position: Beside Fuel cap The port to fill with chain oil Position: Beside Oil cap Setting the switch to the “O” position, the engine stops immediately . Position: Beside rocker switch Starting the engine. If you pull out the choke knob (at the b ...

  • Zenoah G3801EZ - page 6

    G3801/G3801EZ GB-6 3. Fit the chain cover to the power unit and fasten the nuts to finger tightness. 4. While holding up the tip of the bar , adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail. 5. Tighten the nuts securely with the bar tip held up (12 ~ 15 N·m). Then check the ch ...

  • Zenoah G3801EZ - page 7

    G3801/G3801EZ G B GB-7 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refuel- ing the unit. Select outdoor bare ground for fuel- ing and move at least 3 m (10 ft) away from the fueling point before starting the en ...

  • Zenoah G3801EZ - page 8

    G3801/G3801EZ GB-8 6. When engine has ignited, first push in the choke knob to “ST AR T” position and then pull the starter again to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly . At once pulling throttle lever out, the choke knob is automatically returned to the “RUN” position. Keep clear of the ...

  • Zenoah G3801EZ - page 9

    G3801/G3801EZ G B GB-9 1. Stop engine and screw L needle until it stops. Never force. Then set it back the initial number of turns as shown below . H needle is r estricted within the num- ber of turn as shown below . H needle : 1 3 / 8 ± 1 / 4 L needle : 1 1 / 4 ± 1 / 4 2. Start the engine and allow it to war m up in low speed for a few minutes. ...

  • Zenoah G3801EZ - page 10

    G3801/G3801EZ GB-10 A log lying on the ground Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-thir d and finish by sawing down from the top. In ar ea B, saw down fr om the top one-third and finish by sawing up fr om the bot- tom. 6. Sawing • Before proce ...

  • Zenoah G3801EZ - page 11

    G3801/G3801EZ G B GB-11 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. ■ MAINTENANCE AFTER EACH USE 1. Air filter Dust on the cleaner surface can be removed by tapping a corner of the cleaner against a hard surface. T o clean dirt in ...

  • Zenoah G3801EZ - page 12

    G3801/G3801EZ GB-12 4. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 5. Sprocket Check for cracks and for excessive wear interfering with the chain drive. If the wear is considerable, replace it with new one. Never fit a new chain on a worn sprocket, or a worn chain on a new sprocket. Place the file ...

  • Zenoah G3801EZ - page 13

    G3801/G3801EZ G B GB-13 W ARNING: This saw is equipped with one of the following low kick- back bar/chain combinations: Zenoah Part Number Saw Model Chain T ype Guide Bar Saw Chain G3801/G3801EZ 91VG 3608-52112 2932-52210 G3801/G3801EZ 95VP 2939-52110 2939-52210 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, th ...

  • Zenoah G3801EZ - page 14

    G3801/G3801EZ GB-14 11. Specifications POWER UNIT : Displacement (cm 3 ): ................................................................................. 37.2 Fuel: ..................................................................................................... Mixture when using ZENOAH genuine oil (FC grade) ................................ ...

  • Zenoah G3801EZ - page 15

    G3801/G3801EZ G B GB-15 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty period, the failed part will be replaced or repair ed fr ee of charge by a ZENOAH authorized dealer . W ARRANTY PERIOD: Six (6) months after pur chased by end-user subject to 12 months from pr oduced mon ...

メーカー Zenoah カテゴリー Chainsaw

Zenoah G3801EZのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G3801EZの取扱説明書
- Zenoahの製品カード
- パンフレット
- またはZenoah G3801EZの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Zenoah G3801EZの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Zenoah G3801EZの取り付け説明書、サービスマニュアル、簡易説明書、またはZenoah G3801EZのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Zenoah G3801EZの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Zenoah G3801EZデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがZenoah G3801EZを使用するのを助ける技術的文書のことです。説明書は通常、全てのZenoah G3801EZユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Zenoahの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Zenoah G3801EZの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははZenoah G3801EZの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Zenoah G3801EZに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Zenoah G3801EZデバイスの基本機能を使うにあたってのヒント。 Zenoah G3801EZのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Zenoah G3801EZに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるZenoah G3801EZのメーカー/サービスへの連絡先に関する情報。

Zenoah G3801EZについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもZenoah G3801EZの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがZenoah G3801EZで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)