Deutsch dropdown-ico

Bedienungsanleitung Weider WESY49310

33 Seiten 1.29 mb
Download

Zur Seite of 33

Summary
  • Weider WESY49310 - page 1

    QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LINE. The ...

  • Weider WESY49310 - page 2

    1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. Use the weight system only on a level sur- face. Cover the floor beneath the weight sys- tem to protect the ...

  • Weider WESY49310 - page 3

    3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. Width: 1 10 in. Length: 92 in. Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Assist Arm Press Arm Weight Stacks Backrests Dip Handles Pull-up Handles W arning Decal 1 W arning Decal 1 W arning Decal 3 W arning Decal 2 Leg Press Plate Thank you for selecting the versatile CLUB ...

  • Weider WESY49310 - page 4

    4 ASSEMBL Y 1 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press two 2” Square Outer Caps (51) onto the Stabilizer (5). Press a 2” Square Inner Cap (27) into the Base (4). Insert six 5/16” x 2 1 ...

  • Weider WESY49310 - page 5

    5 2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Uprights should be on the side shown. Hand-tighten four 5/16” Nylon Locknuts (3) onto the Carriage Bolts. Do not tighten the Nylon Locknuts yet. Press a 2” Square ...

  • Weider WESY49310 - page 6

    6 4. Press a 2” Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the T op Frame. Press two 1” Inner Caps (1 13) into the top of the crossbar . Attach the T op Frame (55) to the Assist Upright (74) and the Leg Press Upright (56) with two 5/16” x 2 3/4” Bolts (1 ...

  • Weider WESY49310 - page 7

    7 7. Press a Weight Tube Bumper (64) into the end of the Short Weight Tube (108). Insert the Weight Tube into the front stack of W eights (25). Be sure that the pin on the W eight T ube is sitting in the pin grooves in the top Weight. Lubricate the inside of the holes in a T op Weight (65). Set the T op Weight onto the front stack of Weights (25). ...

  • Weider WESY49310 - page 8

    8 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) in the same manner . 10. Locate and open the parts bag labeled “ARM ASSEMBL Y .” Be sure ...

  • Weider WESY49310 - page 9

    9 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner . 13. Identify the Right Arm ...

  • Weider WESY49310 - page 10

    10 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm. Attach the Pivot Arm (101) to the Assist Upri ...

  • Weider WESY49310 - page 11

    11 17. Attach the Left Pull-up Arm (75) and the Right Pull-up Arm (77) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Attach the Left Dip Arm (78) and the Right Dip Arm (79) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Wet the end of th ...

  • Weider WESY49310 - page 12

    12 20. Wrap the High Cable (58) around a “V”-Pulley (50). Attach the “V”-Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place. 21. Route the High Cable (58) around th ...

  • Weider WESY49310 - page 13

    13 24. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”- Bracket. Note: This may come pre-assem- bled. Route the High Cable (58) through the Long “U”- ...

  • Weider WESY49310 - page 14

    14 27. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame. T ighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (not shown). 2 ...

  • Weider WESY49310 - page 15

    15 31. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing. 32. Attach the High ...

  • Weider WESY49310 - page 16

    16 34. Wrap the Military Press Cable (72) around a “V”-Pulley (50). Attach the “V”-Pulley to the T op Frame (55) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley to the indicated bracket on the Assist Arm (105) with a 3/8” x 1 3/4” Bol ...

  • Weider WESY49310 - page 17

    17 36. Slide a 5/16” Flat W asher (8) onto a 5/16” x 2 3/4” Bolt (1 1). Insert the Bolt through the indi- cated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tighten a 5/16” Nylon Jam Nut (93) onto the Bolt. Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable T ...

  • Weider WESY49310 - page 18

    18 38. Locate the Leg Press Cable (99). Attach the end of the Leg Press Cable to the Long “U”- Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing. Wrap the Leg Press Cable ( ...

  • Weider WESY49310 - page 19

    19 40. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Insert a 1/4” x 2 1/2” Carriage Bolt (92) through the center hole in a Seat Plate (37). Attach the Seat Plate to the Rear Backrest (85) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2 1/2” Carriage Bolt (92) through the indicated hole in the Leg Press Upright (56 ...

  • Weider WESY49310 - page 20

    20 43. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat W ashers (10). The Backrest must be oriented as shown. 44. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) through the center hole in the Seat Plate (37). Attach ...

  • Weider WESY49310 - page 21

    47. Press two 3/4” Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Front Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad T ube. 48. Remove the backing from the CLUB WEIDER ® 17.0ST d ...

  • Weider WESY49310 - page 22

    22 HOW T O USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise poster accompanying this manual to see how the weight system should be set up for each exercise. IMPOR- T ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the correct start- ...

  • Weider WESY49310 - page 23

    23 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be sure that ...

  • Weider WESY49310 - page 24

    24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm. WEIGHT PRESS BUTTERFL Y LEG HIGH LOW MILIT AR Y LEG ASSIST PLA TES AR ...

  • Weider WESY49310 - page 25

    TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch slightly when i ...

  • Weider WESY49310 - page 26

    26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight system will ...

  • Weider WESY49310 - page 27

    27 Military Press Cable (72) Leg Press Cable (99) Rear Weight Stack— 1 2 3 4 7 6 5 3 2 4 — Rear Seat Frame 8 — Pivot Arm 1 — Long “U”-Bracket Military Press Cable (72) and Leg Press Cable (99) ...

  • Weider WESY49310 - page 28

    5/16" Nylon Locknut (3) 1/4" Flat W asher (10) 5/16" Flat W asher (8) 3/8" Flat W asher (9) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Locknut (21) 1/4" x 2" Machine Screw (81) 5/16" Nylon Jam Nut (93) 5/16" x 2 1/2" Carriage Bolt (1) 5/16" x 2 3/4" Carriage Bolt (14) 3/8" x 2" ...

  • Weider WESY49310 - page 29

    1" Retainer (69) 3/8" x 3 1/2" Bolt (16) 1/4" x 3/4" Screw (18) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (88) 3/8" x 8" Bolt (59) Cable Clip (53) 1 1/8" x 2 1/2" Plastic Bushing (89) 1" x 7/8" Plastic Bushing (90) 5/16" x 6" Bolt (60) 3 1/2" Pulley (15) (Not sh ...

  • Weider WESY49310 - page 30

    1" Round Inner Cap (49) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 5/16" x 2" Eyebolt (35) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" Square Inner Cap (27) 2" Square Outer Cap (51) 1" Square Inner Cap (6) 1" x 2" Inner Cap (107) 5/ ...

  • Weider WESY49310 - page 31

    P ART LIST—Model No. WESY49310 R1 101A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty . Description 1 10 5/16” x 2 1/2” Carriage Bolt 2 6 1/4” Nylon Locknut 3 36 5/16” Nylon Locknut 4 1 Base 5 1 Stabilizer 6 1 1” Square Inner Cap 7 1 5/8” x 9/16” Spacer 8 9 5/16” Fl ...

  • Weider WESY49310 - page 32

    60 27 21 50 55 86 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 108 64 25 26 19 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48 50 31 86 13 40 38 37 18 32 34 30 28 3 49 83 33 10 2 36 14 15 29 35 30 34 34 30 28 3 8 32 30 34 10 11 3 11 3 81 88 44 44 83 66 66 66 90 89 89 7 3 1 1 ...

  • Weider WESY49310 - page 33

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: • The MODEL NUMBER of the product (WESY49310) • The NAM ...

Produzent Weider Kategorie Home Gym

Dokumente, die wir vom Produzenten des Geräts Weider WESY49310 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Weider
- Bedienungsanleitungen WESY49310
- Produktkarten Weider
- Informationsbroschüren
- oder Energieetiketten Weider WESY49310
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Weider WESY49310.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Weider WESY49310, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Weider WESY49310. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Weider WESY49310 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Weider WESY49310, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Weider WESY49310 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Weider WESY49310 verständlich ist.

Eine gänzliche Bedienungsanleitung von Weider sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Weider WESY49310 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Weider WESY49310 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Weider WESY49310, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Weider WESY49310 - die uns die ersten Schritte während der Nutzung von Weider WESY49310 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Weider WESY49310 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Weider WESY49310 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Weider WESY49310?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Weider WESY49310 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Weider WESY49310 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)