Bedienungsanleitung Packard Bell A7

25 Seiten 7.78 mb
Download

Zur Seite of 25

Summary
  • Packard Bell A7 - page 1

    V ersa S940 Disassembly Manual ...

  • Packard Bell A7 - page 2

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 2 Table of contents Overview....................................................................................................................... .......................................... 3 Technician Notes ...................................................................................... ...

  • Packard Bell A7 - page 3

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 3 Overview This document contains step-by-steps disassembly inst ructions for the Versa S940/EasyNote A7 chassis. The instructions are illustrated where necessary with images of the part that is being removed o r disassembled. Furthermore, the screws that are removed are s how n next to the imag ...

  • Packard Bell A7 - page 4

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 4 Hazardous Voltag e There is hazardous voltage pr esent inside the computer when it is connect to an AC supp ly , even w hen the computer’s power switch is off. Exposur e to hazardous voltage could cause personal injury. To avoid r isk of injury, contact an Authorized Service Provider for pro ...

  • Packard Bell A7 - page 5

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 5 Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa S94 0/EasyNote A7. 2. Turn the unit upside down. 3. Unlock the battery an d slide it out of its place as the ar row shows in Fig. 1 Fig. 1 Re moving the battery ...

  • Packard Bell A7 - page 6

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 6 Removing the Memory Module To remove the Memory Module, first remove th e battery (see Removing the Battery ), then perform the following steps: 1. Release the three screw s retaining the memory module cov er. Fig. 2 Re moving the screws retaining the memory module slot cover 2. Unclip the mem ...

  • Packard Bell A7 - page 7

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 7 Removing the WLAN Card Module To remove the WLAN Card Module, first remove the Memor y Module Cover (see Removing Memory Module ) then perform the following steps: 1. Disconnect the wireless ante nna connector and release the WLAN Car d Module as shown in Error! Reference source not found. Fig ...

  • Packard Bell A7 - page 8

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 8 Removing the Hard Disk Drive To remove the hard disk drive, first remo ve the batter y (see Removing th e Battery ), then perform the following steps: 1. Remove the screw s as s how n in Fig. 5 Fig. 5 Removing the Hard disk drive cover 2. Carefully pull the HD D mo dule out fro m the bas e uni ...

  • Packard Bell A7 - page 9

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 9 3. Remove four screws that around HDD module. Fig. 7 HDD module Note: When installing HDD, make sure the HDD mod ule st rap pro perly insert into base unit as shown in below picture. M4x3 S ilver ...

  • Packard Bell A7 - page 10

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 10 Removing the Optical Disk Drive To remove the ODD, first remove the battery (s ee Removing the Battery ) and Memory M odule Cove r (s e e Removing Memory Module ) then perform the follow ing steps: 1. Use pin to eject the optical dr ive via emergency eject hole as shown in Fig. 8 Fig. 8 Eject ...

  • Packard Bell A7 - page 11

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 11 Removing the CPU To remove the CPU first remove the battery (see Rem oving the B attery ) then perform the following st eps: 1. Losses four screws that re taining the CPU cover as sh own in Fig. 10 Fig. 1 0 Removing the screws retaining CPU cover 2. Remove the CPU Fan scre ws, disconnect the ...

  • Packard Bell A7 - page 12

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 12 3. Unlock the CPU from the CPU socket and lift up the CPU carefully. Fig. 12 Unlocking the CPU ...

  • Packard Bell A7 - page 13

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 13 Removing the Keyboard To remove the Keyboard , first remove the batte ry (see Removing the Batter y ), then perform the following steps: 1. Release two screws on keyboard cover as shown in Fig. 13 Fig. 13 Releasing the keyboard cover 2. Lift up the keyboard cover carefully as sho wn in Fig. 1 ...

  • Packard Bell A7 - page 14

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 14 3. Unscr ew two s crews at the botto m as show n in Fig. 15 Fig. 15 Unscrewing Keyboard screws Caution: If using wrong screws during keyboard assemble mi ght result damage to keyboard. Thus please mark those screws carefully during disse mble. 4. Flip over the unit and release remain ing scre ...

  • Packard Bell A7 - page 15

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 15 5. Lift up the keyboard and disconnect it fr om the system as shown in Fig. 17 Fig. 17 Disconnecting the keyboard flat cable Removing the LCD Module To remove the LCD Module first remove the battery (see Removing the Battery ), remove WLAN Card Module (see Removing WLAN Card Module )and remov ...

  • Packard Bell A7 - page 16

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 16 2. Disconnect LCD Cable Conne ction and remove four screws retaining the Heat Plate as shown in Fig. 19 Fig. 1 9 Removing the screws retaining the LCD module 3. Carefully lift up the LCD Module. M2.5x6 Silver ...

  • Packard Bell A7 - page 17

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 17 Removing the LCD Pane l To remove the LCD panel, first remo ve the LCD module (see Removing the LCD Modu le ), then perform t he following st eps: 1. Use a pin to remove the r ubber cover on the LCD module as shown in Fig. 20 2. Remove all screws as shown in Fig. 20 and remove car efully the ...

  • Packard Bell A7 - page 18

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 18 4. Release four screws at the both side of LCD hinge as shown in Fig. 22 Fig. 22 Unscrew LCD Penal 5. Disconnect all connectors on inverter board as shown in Fig. 23 Fig. 23 Removing the Inverter Board 6. Carefully lift up the LCD panel. 7. Remove the screws at both side s of the LCD panel in ...

  • Packard Bell A7 - page 19

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 19 Removi ng the Top Cover To remove the Top Cover , first remove the battery (see Removing the Battery ), remove the HDD (see Remov ing the H ard Disk Dr iv e ), remove the Optical Disk Drive (see Removin g th e Optical Disk Drive ), remove the CPU (see Removing the CPU )remove the Ke yboard (s ...

  • Packard Bell A7 - page 20

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 20 3. Disconnect the Touch Pad Connector and remove all screws as shown in Fig. 27 Fig. 27 Top cover 4. Carefully lift up the Top C over. A = M2.5x4 Si lver B = M2.5x5 Silver ...

  • Packard Bell A7 - page 21

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 21 Removing the Main Board To remove the Main Board, first rem ove the Top Cover (see Removing Top Cover ) then perform the following steps: 1. Remove all connection and screws on main board as shown in Fig. 28 Fig. 28 Main board 2. Carefully lifting up main boar d from the rear of the un it as ...

  • Packard Bell A7 - page 22

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 22 3. Dis connect Audio board fr om main bo ard as shown in Fig. 30 Fig. 30 VGA board 4. This step only applicable to EasyNote A7. Flip over the main board and release two screws on S-Video Board as shown in Fig. 31 Fig. 31 S-video board on Main Board M2.5x6 Silver M2x3 S ilver ...

  • Packard Bell A7 - page 23

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 23 Removing the Speaker Assembly To remove the Speaker Assembly, first re move the Main Board (see Remo vin g th e Ma in Board ) then perform the following steps: 1. Remove the screws holding Speaker Assembly as shown in Fig. 32 Fig. 32 Speaker Assembly 2. Carefully remove the Speaker assembly f ...

  • Packard Bell A7 - page 24

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 24 DIP Switch Settings No DIP switch available on ED1 platform. Screws M2.5x2.5 Silver M2.5x4 Silver M2.5 x8 Copper M2.5x5 Black M2.5x5 Silver M2.5x6 Silver M2.5x6 Copper M2x7 Silver M2x3 Silver M2x4 Silver M2.5x4 Co pp er M2.5x3 Silver M2x4.5 Black M4x3 Silver ...

  • Packard Bell A7 - page 25

    NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 25 Notice The information in this guide is subject to chan ge without notice. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without pr ior written consent from NEC Computer s International BV. NEC COMPUT ...

Produzent Packard Bell Kategorie Laptop

Dokumente, die wir vom Produzenten des Geräts Packard Bell A7 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Packard Bell
- Bedienungsanleitungen A7
- Produktkarten Packard Bell
- Informationsbroschüren
- oder Energieetiketten Packard Bell A7
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Packard Bell A7.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Packard Bell A7, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Packard Bell A7. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Packard Bell A7 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Packard Bell A7, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Packard Bell A7 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Packard Bell A7 verständlich ist.

Eine gänzliche Bedienungsanleitung von Packard Bell sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Packard Bell A7 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Packard Bell A7 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Packard Bell A7, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Packard Bell A7 - die uns die ersten Schritte während der Nutzung von Packard Bell A7 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Packard Bell A7 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Packard Bell A7 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Packard Bell A7?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Packard Bell A7 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Packard Bell A7 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)