Bedienungsanleitung Zenoah G3300EZ

16 Seiten 0.99 mb
Download

Zur Seite of 16

Summary
  • Zenoah G3300EZ - page 1

    G3300 / G3300EZ GB-1 G B G3300 G3300EZ OWNER’S MANUAL CHAINSA WS G B 848C3593A1 (411) ...

  • Zenoah G3300EZ - page 2

    G3300 / G3300EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book bef ore operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickbac k. Read, understand and f ollow all w arnings. W ARNING!!! RISK OF DAMAGING HEARING IN NORMAL CONDITIONS OF USE, T ...

  • Zenoah G3300EZ - page 3

    G3300 / G3300EZ GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Chain Oil .......................................... ...

  • Zenoah G3300EZ - page 4

    G3300 / G3300EZ GB-4 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medica- tion that may make you drowsy , or if you are under the influence of alcohol or drugs. 2. Use safety footwear , snug fitting clothing and eye, hearing and head protection devices. Use the vibration-proof gl ...

  • Zenoah G3300EZ - page 5

    G3300 / G3300EZ GB-5 G B move the clutch, structural dam- age to the flywheel could occur which could subsequently cause the flywheel to disintegrate.) 16. Always shut off the engine be- fore setting it down. 17. Use extreme caution when cut- ting small size brush and sap- lings because slender material may catch the saw chain and be whipped toward ...

  • Zenoah G3300EZ - page 6

    G3300 / G3300EZ GB-6 [G3300] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut and remove the chain cover . 3. Gear the chain to the sprocket and, while fitting the saw chain around the guide bar , mount the guide bar to the power unit. Adjust the position of the chain tensioner . Pay attent ...

  • Zenoah G3300EZ - page 7

    G3300 / G3300EZ GB-7 G B [G3300EZ] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut assembly and dismount the chain cover . (1) (2) (3) 3. Set the guide bar to the power unit, gear the chain to the sprocket of clutch drum and fit it into the gr oove of the bar and the sprocket at the tip of ...

  • Zenoah G3300EZ - page 8

    G3300 / G3300EZ GB-8 ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 • Exhaust emission are controlled b y the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of an y major hard ware or the intro- duction of an inert material during combustion. • These engines are certified ...

  • Zenoah G3300EZ - page 9

    G3300 / G3300EZ GB-9 G B Do not start the engine while the chain saw hangs in one hand. The saw chain may touch your body . This is ver y danger ous. 6. When engine has ignited, pull the throttle slightly to r eturn the choke knob to the original position. If the engine stops, pull the starter again without pulling out the choke knob. 7. Allow the ...

  • Zenoah G3300EZ - page 10

    G3300 / G3300EZ GB-10 The carburetor on your unit has been factory adjusted, but may requir e fine tuning due to a change in operat- ing conditions. Before adjusting the carbur etor , make sure that the pr o- vided air/fuel filters are clean and fr esh and the fuel prop- erly mixed. When adjusting, take the following steps: Note: Be sure to adjust ...

  • Zenoah G3300EZ - page 11

    G3300 / G3300EZ GB-11 G B gine at full speed. If the chain is slow to stop or does not stop, replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to main- tain the kickback safety level of this saw . Removal of the s ...

  • Zenoah G3300EZ - page 12

    G3300 / G3300EZ GB-12 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to pre- vent accidental starting. ■ MAINTENANCE AFTER EA CH USE 1. Oiling port Dismount the guide bar and check the oiling port for clogging. 7. Maintenance A log lying on the gr ound Saw down half ...

  • Zenoah G3300EZ - page 13

    G3300 / G3300EZ GB-13 G B 2. Fuel filter Using a wire hook, take out the filter fr om the filler port. Clean away the dirt attached to the filter . Replace with a new one if needed. Note: Never bend the filter pipe when returning it. 3. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 4. Cylinder fins D ...

  • Zenoah G3300EZ - page 14

    G3300 / G3300EZ GB-14 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced. W ARNING: This saw is equipped with one of the following low kickback bar/chain combinations: Komatsu Zenoah Part Number Saw Model Bar Size Guide Bar Saw Chain G3300/G3300EZ ...

  • Zenoah G3300EZ - page 15

    G3300 / G3300EZ GB-15 G B 9. T r oubleshooting Guide Case 1. Starting failure Make sure the icing pr evention system is not working. Check fuel for water or substandard mix- ture. Replace with proper fuel. Check for engine flooding. Check spark ignition. Remove and dry the spark plug. Then pull the starter again with no choke. Replace with a new pl ...

  • Zenoah G3300EZ - page 16

    G3300 / G3300EZ GB-16 Limited warranty Should any failure occur on the pr oduct under nor mal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a KOMA TSU ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profes- sionally , and 30 days if used for rental ...

Produzent Zenoah Kategorie Chainsaw

Dokumente, die wir vom Produzenten des Geräts Zenoah G3300EZ erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Zenoah
- Bedienungsanleitungen G3300EZ
- Produktkarten Zenoah
- Informationsbroschüren
- oder Energieetiketten Zenoah G3300EZ
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Zenoah G3300EZ.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Zenoah G3300EZ, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Zenoah G3300EZ. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Zenoah G3300EZ ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Zenoah G3300EZ, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Zenoah G3300EZ hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Zenoah G3300EZ verständlich ist.

Eine gänzliche Bedienungsanleitung von Zenoah sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Zenoah G3300EZ bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Zenoah G3300EZ befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Zenoah G3300EZ, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Zenoah G3300EZ - die uns die ersten Schritte während der Nutzung von Zenoah G3300EZ erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Zenoah G3300EZ hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Zenoah G3300EZ im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Zenoah G3300EZ?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Zenoah G3300EZ nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Zenoah G3300EZ hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)