-
Zenoah G3300EZ - page 1
G3300 / G3300EZ GB-1 G B G3300 G3300EZ OWNER’S MANUAL CHAINSA WS G B 848C3593A1 (411) ...
-
Zenoah G3300EZ - page 2
G3300 / G3300EZ GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book bef ore operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickbac k. Read, understand and f ollow all w arnings. W ARNING!!! RISK OF DAMAGING HEARING IN NORMAL CONDITIONS OF USE, T ...
-
Zenoah G3300EZ - page 3
G3300 / G3300EZ GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ......................................... 6 4. Fuel and Chain Oil .......................................... ...
-
Zenoah G3300EZ - page 4
G3300 / G3300EZ GB-4 1. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medica- tion that may make you drowsy , or if you are under the influence of alcohol or drugs. 2. Use safety footwear , snug fitting clothing and eye, hearing and head protection devices. Use the vibration-proof gl ...
-
Zenoah G3300EZ - page 5
G3300 / G3300EZ GB-5 G B move the clutch, structural dam- age to the flywheel could occur which could subsequently cause the flywheel to disintegrate.) 16. Always shut off the engine be- fore setting it down. 17. Use extreme caution when cut- ting small size brush and sap- lings because slender material may catch the saw chain and be whipped toward ...
-
Zenoah G3300EZ - page 6
G3300 / G3300EZ GB-6 [G3300] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut and remove the chain cover . 3. Gear the chain to the sprocket and, while fitting the saw chain around the guide bar , mount the guide bar to the power unit. Adjust the position of the chain tensioner . Pay attent ...
-
Zenoah G3300EZ - page 7
G3300 / G3300EZ GB-7 G B [G3300EZ] 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged. 2. Loosen the nut assembly and dismount the chain cover . (1) (2) (3) 3. Set the guide bar to the power unit, gear the chain to the sprocket of clutch drum and fit it into the gr oove of the bar and the sprocket at the tip of ...
-
Zenoah G3300EZ - page 8
G3300 / G3300EZ GB-8 ■ RECOMMENDED MIXING RA TIO GASOLINE 50 : OIL 1 • Exhaust emission are controlled b y the funda- mental engine parameters and components (eq., carburation, ignition timing and port timing) with- out addition of an y major hard ware or the intro- duction of an inert material during combustion. • These engines are certified ...
-
Zenoah G3300EZ - page 9
G3300 / G3300EZ GB-9 G B Do not start the engine while the chain saw hangs in one hand. The saw chain may touch your body . This is ver y danger ous. 6. When engine has ignited, pull the throttle slightly to r eturn the choke knob to the original position. If the engine stops, pull the starter again without pulling out the choke knob. 7. Allow the ...
-
Zenoah G3300EZ - page 10
G3300 / G3300EZ GB-10 The carburetor on your unit has been factory adjusted, but may requir e fine tuning due to a change in operat- ing conditions. Before adjusting the carbur etor , make sure that the pr o- vided air/fuel filters are clean and fr esh and the fuel prop- erly mixed. When adjusting, take the following steps: Note: Be sure to adjust ...
-
Zenoah G3300EZ - page 11
G3300 / G3300EZ GB-11 G B gine at full speed. If the chain is slow to stop or does not stop, replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to main- tain the kickback safety level of this saw . Removal of the s ...
-
Zenoah G3300EZ - page 12
G3300 / G3300EZ GB-12 Before cleaning, the inspecting or r epairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to pre- vent accidental starting. ■ MAINTENANCE AFTER EA CH USE 1. Oiling port Dismount the guide bar and check the oiling port for clogging. 7. Maintenance A log lying on the gr ound Saw down half ...
-
Zenoah G3300EZ - page 13
G3300 / G3300EZ GB-13 G B 2. Fuel filter Using a wire hook, take out the filter fr om the filler port. Clean away the dirt attached to the filter . Replace with a new one if needed. Note: Never bend the filter pipe when returning it. 3. Spark plug Clean the electrodes with a wir e brush and reset the gap to 0.65 mm as necessary . 4. Cylinder fins D ...
-
Zenoah G3300EZ - page 14
G3300 / G3300EZ GB-14 side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced. W ARNING: This saw is equipped with one of the following low kickback bar/chain combinations: Komatsu Zenoah Part Number Saw Model Bar Size Guide Bar Saw Chain G3300/G3300EZ ...
-
Zenoah G3300EZ - page 15
G3300 / G3300EZ GB-15 G B 9. T r oubleshooting Guide Case 1. Starting failure Make sure the icing pr evention system is not working. Check fuel for water or substandard mix- ture. Replace with proper fuel. Check for engine flooding. Check spark ignition. Remove and dry the spark plug. Then pull the starter again with no choke. Replace with a new pl ...
-
Zenoah G3300EZ - page 16
G3300 / G3300EZ GB-16 Limited warranty Should any failure occur on the pr oduct under nor mal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a KOMA TSU ZENOAH authorized dealer . W ARRANTY PERIOD: 1 year (6 months if used profes- sionally , and 30 days if used for rental ...
¿Tienes una pregunta acerca de Zenoah G3300EZ?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zenoah G3300EZ, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zenoah G3300EZ probablemente compartirá una forma de solucionarlo.