Deutsch dropdown-ico

Bedienungsanleitung Harmar Mobility AL500

36 Seiten 10.87 mb
Download

Zur Seite of 36

Summary
  • Harmar Mobility AL500 - page 1

    AL500 Universal Power Chair Lift AL100 Universal Scooter Lift AL550 A utomatic Power Chair Lif t AL 560 A uto Hold Down P .C. Lift Outside Lif t Capacity: 350 lbs Capacity: 350 lbs Capacity: 350 lbs Capacity: 350 lbs AL030 Power T ote for Manual Wheelchairs M O B I L ITY M O B I L I T Y Capacity: 100 lbs AL300 Universal Power Chair / Scooter Lift C ...

  • Harmar Mobility AL500 - page 2

    PLATFORM KEEPER WELDE D TO P LATF OR M LIFT AL030 - Manual Wheelchair Lift LIFT BODY HITCH ADAPTER and Stabil izer HARDWARE PACK HITCH POST Unpacking the Lif t Y our Universal Outside Lift was factory pre- assembled to require little assembly before installa tion. Box contents should include: Be sure and check the contents of the box against the pa ...

  • Harmar Mobility AL500 - page 3

    BEGIN ROUTING THE VEHICLE HARNESS A T THE BA TTERY Attach the black wire to the negative terminal on the battery. Do not attach the red wire yet. Important Reminder: Never attempt to attach the wire harness to a secondary power source. The harness requires direct connection to the battery. Caution: R oute the harness away from the exhaust system, b ...

  • Harmar Mobility AL500 - page 4

    V ehicle Hitch lbs Must NOT Exceed Hitch Manufacturer's Max T ongue Weight OR X lbs Chair / Scooter IF USED 40 lbs Swing Away Not for AL030 T o install an Outside Lift on a vehicle, the vehicle must be capable of accepting a Class 2 or Class 3 hitch. If you are unsure about the vehicle and hitch compatibility, cont act a local hitch installer ...

  • Harmar Mobility AL500 - page 5

    AL123 Standard Class 3 AL125 Class 3 Extra long H124 Class 3 Short AL1232 2in Drop Class 3 AL1236 6in Drop Class 3 H128 Class 2 Short AL1235 5in Drop Class 3 AL1265 4in Drop Class 2 AL127 Class 2 Extra long AL126 Standard Class 2 A Hitch Adapter is the part of the lift that plugs into a vehicle's trailer hitch. Several hitch adapters are avail ...

  • Harmar Mobility AL500 - page 6

    OR Attach Lift to Hitch Post or Swing A way SWING AW A Y HITCH ADAPTER Measure from Hitch Bar to ground In order to determine how to assemble the Hitch Post and Hitch Adapter , the distance from the bottom of the hitch to the ground must be measured. Determine which set of holes to use to bolt together the Hitch Post and Hitch Adapter . Use the 1/2 ...

  • Harmar Mobility AL500 - page 7

    M O B I L I T Y For AL030 ONLY Bumper Mount ( Be sure to comply with vehicle's bumper rating ) Flat Bar S tyle ( Be sure to comply with vehicle's bumper rating ) Omit stabilizer Do not attempt to mount up from under FOR AL030 O NL Y ( Ball Mount Hitch adapter ) Ball Mount Hitch Adapter and stabilizer Ball Mount Hitch Adapter can NOT be us ...

  • Harmar Mobility AL500 - page 8

    Power Chair or Scooter Preparation AL600 & AL690 ALA580 U-BOLT H ARDWAR E KIT ANCHOR U-BOLTS: THE U-BOLTS ARE TO BE USED WITH POWER CHAIRS OR SCOOTERS THA T DO NOT HAVE A CENTER SEA T POST . ON THIS TYPE OF CHAIR, THE SEAT IS NORMALLY ATT ACHED TO A TUBULAR FRAME. A TTACH THE U-BOL TS, TWO ON EACH SIDE, TO THE FRAME AS SHOWN BELOW . MAKE SURE T ...

  • Harmar Mobility AL500 - page 9

    AL550 only CHOOSING A LOCATION and MOUNTING THE DOCKING DEVICE PLATE Find approximate center of the chair The closer the plate is positioned to the drive wheels, the easier the chair will be to engage the Locking Device Drive wheel Use existing holes where ever possible. If too little or no holes exist, holes need to be drilled. Remove power chair& ...

  • Harmar Mobility AL500 - page 10

    AL550 only SETTING DOCKING DEVICE HEIGHT 0.25" 0.25" 1.00" 1.00" 0.25" 0.25" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 1.00" 0.25" 0.25" 1.00" 1.00" 0.50" 0.50" 0.25" 0.50" 0.25" 0.50" 1.00" 1.00" 0.50" 0.50" 0 ...

  • Harmar Mobility AL500 - page 11

    DO NOT With platform on the ground, drive scooter onto platform , from left (driver's side ) to right, until the rear wheels are located in the rear wheel spreader bar assembly . S top when the rear tires conta ct the ramp on the platform. Raise the platform on either lift u ntil the motor's clutch is heard ( top of travel ). Loosen both ...

  • Harmar Mobility AL500 - page 12

    Loosen nuts here Slide arm up or down tube Tighten after adjustment N O I S N E T T S U J D A LIFT SHOULD HOLD WHEELCHAIR FIRMLY WITH THE PLATFORM FULLY RAISED ( RAISED UNTIL MOTOR RATCHETING IS HEARD ) The hinge points are equipped with tensioning washers. The amount of force required to move these parts is determined by the tension of these washe ...

  • Harmar Mobility AL500 - page 13

    LIFT PREPARA TION AL 560 3/16 “ ALLEN WRENCH REQUIRED FOR ADJUSTMENT PURPOSES, ALL PLA TFORM COMPONENTS ARE SHIPPED LOOSE AND MUST BE FIRMLY TIG HTENED IF NECESSAR Y, T HE COMPONENTS MAY BE RE-ARRAN GED FOR FRONT or REAR DRIVE WHEELS X4 X4 X8 X8 US E FOR DRIVE WHEELS US E FO R D R IVE WHEELS USE FOR DRIVE WHEELS U S E FO R D R I V E WH EE L S SLI ...

  • Harmar Mobility AL500 - page 14

    LIFT PREPARA TION HOLD DOWN ARM HEIGHT ADJUSTMENT AL 560 LOOSEN BOL TS TIGHTEN BOL TS HIGHER ARM SETTINGS CAN BE ACHIEVED BY REMOVING TOP SHAFT COLLAR, RETRACTING T HANDLE AND RE-INSERTING ARM FROM ABOVE. THIS METHOD ALLOWS THE RED “T” HANDLE TO REMAIN ON THE SAME SIDE AS THE KEY AND TOGGLE SWITCHES. DRIVE CHAIR ON PLATFORM PULL RED “T” HAN ...

  • Harmar Mobility AL500 - page 15

    REAR WHEELS FRONT WHEELS General Operating Instructions: Turn the key switch to the ON position. With the toggle switch, raise and lower the platform a s needed. Pushing the switch downward will cause the platform to lower. The plat form will first unfold to the horizontal posit ion, then continue lowering to the ground. Release the UP/DOWN toggle ...

  • Harmar Mobility AL500 - page 16

    T o unload the power chair, simply turn ON the power switch and push the UP/DOWN toggle switch to the down position. Hold the s witch down until the platform just touches and is level to the ground. Press the red release button on the Anchor S trap Base to release the tension and unhook the strap from the chair. Continuing to press the button, allo ...

  • Harmar Mobility AL500 - page 17

    ON DOWN UP THREE WA YS TO VERIFY YOUR CHAIR IS SUCCESSFULLY LOCKED DOWN 1) AUDIBLE "CLICK or POP" SOUND 3) REVERSE TEST 2) VISUAL INDICAT OR SLOW NOT LOCKED LOCKED The yellow indicator will extend and stay extended when the chair is successfully locked in place. Attempt to back the chair off the platform. The chair will NOT move in any di ...

  • Harmar Mobility AL500 - page 18

    V ehicle Hitch OPERA TOR RESPONSIBILITY - AL 550 VERIFY THE CHAIR HAS BEEN LOCKED INTO THE DOCKING ST A TION BY A TTEMPTING TO DRIVE CHAIR OFF IN REVERSE THE DOCKING STA TION WILL “CLICK” or “POP” AND The YELLOW INDICAT OR WILL EXTEND BUT THE MOST EFFECTIVE W AY TO ASSURE THE SAFETY OF YOUR POWER CHAIR IS TO PERFORM THE REVERSE TEST EACH ...

  • Harmar Mobility AL500 - page 19

    TO RELEASE CHAIR Slide knob this direction Slowly back chair off platform NOTE: During transport, vibration may cause the chair to tighten itself in the locking device, making the release knob difficult to slide. T o overcome this, simply drive the chair forward a bit. This will take pressure off the knob, allowing an easier release. UNLOADING THE ...

  • Harmar Mobility AL500 - page 20

    Insert Key and switch to "ON" position Press down on T oggle switch momentarily. Once platform has been lowered at least an inch, unfold the platform. Continue lowering to the ground. Drive scooter onto platform as shown. Raise platform until hold down foot depresses scooter's deck or until lift's motor ratchets. 1 2 3 4 5 T o r ...

  • Harmar Mobility AL500 - page 21

    1 Insert Key and switch to "ON" position Press down on T oggle switch momentarily. Once platform has been lowered at least an inch, unfold the platform. Continue lowering to the ground. 2 ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch. WELDE D T ...

  • Harmar Mobility AL500 - page 22

    V ehicle Hitch OPERATION LOADING THE WHEELCHAIR AL030 ON DOWN UP "PLA TFORM KEEPER" NOTE: The Platform will not be allowed to unfold until the platform has been lowered at least an inch. WE LDED TO PLAT FORM Insert Key and switch to "ON" position Press down on T oggle switch momentarily. 1 Once platform has been lowered at least ...

  • Harmar Mobility AL500 - page 23

    OPERATION Drive the Chair onto the platform taking care to stop when the drive wheels fall between the bars in the platform. 2 AL 560 LOADING A POWER CHAIR ON DOWN UP 1 Insert Key and switch to "ON" position Press down on T oggle switch and the platform will unfold. Continue to lower until platform reaches the ground and becomes level. ON ...

  • Harmar Mobility AL500 - page 24

    OPENING THE SWING AW A Y: IMPORT ANT CAUTION!! Many scooter and chair owners require access to the rear of a vehicle. T o accomplish this a Swing Away o ption is added to the lift installation. Thi s allows the complete lift t o be conveniently and easily swung away from the back of the vehicle and allow easy access to the trunk or lift gate. The S ...

  • Harmar Mobility AL500 - page 25

    Safety & Maintenance Inspect the condition of your lift often. If any parts are worn or damaged DO NOT USE THE LIFT . Immediately contact the dealer you purchased the lift from for repairs. Caution: Keep feet and any other objects out from under the platform as it lowers. Caution: Some chairs and scooters have pneumatic (air inflated) tires. If ...

  • Harmar Mobility AL500 - page 26

    T roubleshooting Guide Check the attachment of the Hitch Adapter to the Hitch Post on the back of the lift . The normal range of operation for the lift is 5 to 18 inches to the bottom of the hitch. The lift should be installed at the highest position possible. Enter driveways at an angle Check the power supply. The wiring harness ( both wires ) mus ...

  • Harmar Mobility AL500 - page 27

    EXPLODED VIEW - AL-010/050 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 27 ...

  • Harmar Mobility AL500 - page 28

    V ehicle Hitch EXPLODED VIEW - AL-030 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 28 ...

  • Harmar Mobility AL500 - page 29

    EXPLODED VIEW - AL-100 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 29 ...

  • Harmar Mobility AL500 - page 30

    V ehicle Hitch EXPLODED VIEW - AL-300 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 30 ...

  • Harmar Mobility AL500 - page 31

    EXPLODED VIEW - AL-301XL + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 31 ...

  • Harmar Mobility AL500 - page 32

    V ehicle Hitch EXPLODED VIEW - AL-500 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 32 ...

  • Harmar Mobility AL500 - page 33

    EXPLODED VIEW - AL-550 + KEYSWITCH ACTUA T OR 12V POLE REVERSING SWITCH BA TTER Y TRAILER PLUG MOTOR COVER LIGHT BROW N CIRCUIT BREAKER VEHICLE HARNESS 33 ...

  • Harmar Mobility AL500 - page 34

    V ehicle Hitch 1 2 ASSEMBLY PAR TS ITE M QT Y P AR T NO. DESCRIPTIO N 12 9961K310 SHAFT COLLAR, 1-1/4" BORE 21 ALA03059 FOAM RUBBER GRIP 12in LONG 31 ALA050E C E-CLIP 41 ALA10010REV 2 ACUTAT OR 51 ALA100REV 2 INNERTUB E 61 ALA1101 0 J-CA M 71 ALA12010 TOGGLE SWITCH (AL100/500) 81 ALA12015 KEY SWITCH ( TUMBLER & KEY) 91 ALA12055REV 2 SWITCH ...

  • Harmar Mobility AL500 - page 35

    ASSEMBLY PARTS ITE M QT Y P A R T NO. DESCRIPTIO N 1 12 H56033 SLIDERNUT, BRACKET - AL56 0 PLATFORM 24 H56040 BRACKET, SKIN - AL560 32 H56050 SKIN, PLATFO RM - AL560 44 H56060 BRACKET, WHE EL CRADDLE - AL560 52 H56070 WHEEL CRADDLE - AL560 61 H56080 PLATFORM WELDMENT - AL560 78 MMC_NO_93310A5 35 SHCS, 1/4-20 x 3/8", w/ NYLON PATCH, 18-8SS 84 M ...

  • Harmar Mobility AL500 - page 36

    V ehicle Hitch HARMAR MOBILITY - 2075 47TH ST - SARASOT A, FL 34234 - 866.351.2776 - WWW.HARMAR.COM ...

Produzent Harmar Mobility Kategorie Mobility Aid

Dokumente, die wir vom Produzenten des Geräts Harmar Mobility AL500 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Harmar Mobility
- Bedienungsanleitungen AL500
- Produktkarten Harmar Mobility
- Informationsbroschüren
- oder Energieetiketten Harmar Mobility AL500
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Harmar Mobility AL500.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Harmar Mobility AL500, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Harmar Mobility AL500. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Harmar Mobility AL500 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Harmar Mobility AL500, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Harmar Mobility AL500 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Harmar Mobility AL500 verständlich ist.

Eine gänzliche Bedienungsanleitung von Harmar Mobility sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Harmar Mobility AL500 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Harmar Mobility AL500 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Harmar Mobility AL500, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Harmar Mobility AL500 - die uns die ersten Schritte während der Nutzung von Harmar Mobility AL500 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Harmar Mobility AL500 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Harmar Mobility AL500 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Harmar Mobility AL500?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Harmar Mobility AL500 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Harmar Mobility AL500 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)