Bedienungsanleitung Rubbermaid 5L20

18 Seiten 14.99 mb
Download

Zur Seite of 18

Summary
  • Rubbermaid 5L20 - page 1

    5L20 76 ¾" 51 ½" 55 ¼" 1780069 Note: Be sure to keep this instruction manual and your original store receipt to ensure our Consumer Service Department can accurately and quickly assist you if necessary . Congratulations and thank you for pur chasing a Rubbermaid storage building . BEFORE YOU BEGIN – BUILDING CODES Be sure to che ...

  • Rubbermaid 5L20 - page 2

    Description Part Number Assembly Letter Quantity Required T ools T wo Person Assembly Floor Front Floor 5L01 A 1 Repeat Floor 5L11 B 1 Walls Repeat Left Side 5L12 C 1 Left Back 5L04 D 1 Repeat Right Side 5L13 E 1 Right Back 5L05 F 1 Front Left Side 5L02 G 1 Front Right Side 5L03 H 1 Wall Connector 5H75 Q 15 Doors Left Door 5L06 / 5L41 L 1 Right Doo ...

  • Rubbermaid 5L20 - page 3

    Build a solid, level surface for the shed foundation. Consult your local building authority for ordinances, restrictions, or permits required before building any structure at your home. Note: Minimum dimensions for foundations shown. FLOOR PLAN: Size the construction site to fit the entire floor . OPTIONAL STEP: If desired, recessed anchor locati ...

  • Rubbermaid 5L20 - page 4

    A B 2 . 0 Floor Installation A Using a rubber mallet and screwdriver , knock out the tabs for the door hinge, 2 places on Front Floor (A) . c . Drill pilot hole through top sur face of floor , 2 places on Front Floor (A) . d . A Using a rubber mallet and screwdriver , punch out the screw holes along the connection edge of Repeat Floor (B) . a . B ...

  • Rubbermaid 5L20 - page 5

    A B 2 . 1 Floor Installation Connect and align Repeat Floor (B) to Front Floor (A) and install Screws (AA) 9 places; keep panels aligned and even while installing screws. a . AA (9) HELPFUL HINT : Pilot holes may be drilled for the screws using a 1/8" drill bit. CAUTION: Do not overtighten screws. 3 . 0 W all Panel C Installation Using a screw ...

  • Rubbermaid 5L20 - page 6

    3 . 1 W all Panel D Installation Snap Repeat Left Side (C) into the back position of Repeat Floor (B) . b . C ALIGN ALIGN click Hold Repeat Left Side (C) upright to prevent it from falling (until Left Back (D) is installed). c . C D D Using a screwdriver , punch out the screw holes on the top of Left Back (D) 4 places. a . Screw Holes ...

  • Rubbermaid 5L20 - page 7

    1 2 D C C OVERHEAD VIEW DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B AND 3-5_B SCALE 1/1 DETAIL 3-6_B AND 3-7_B SCALE 1/1 Connect Left Back (D) into dovetails of Repeat Left Side (C) . b . Engage snaps on bottom of Left Back (D) into Repeat Floor (B) . c . HELPFUL HINT : Lubricate dovetails with liquid soap. D 1 ...

  • Rubbermaid 5L20 - page 8

    Snap Repeat Right Side (E) into the back position of Repeat Floor (B) . b . Hold Repeat Right Side (E) upright to prevent it from falling (until Right Back (F) is installed). c . E ALIGN ALIGN click click 3 . 3 W all Panel F Installation Using a screwdriver , punch out the screw holes on the top of Right Back (F) 4 places. a . F F Screw Holes ...

  • Rubbermaid 5L20 - page 9

    Connect Right Back (F) onto dovetails of Repeat Right Side (E) . Align the lap joint between Left Back (D) and Right Back (F). b . Engage snaps on bottom of Right Back (F) into Repeat Floor (B) . c . DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B AND 3-5_B SCALE 1/1 DETAIL 3-6_B AND 3-7_B SCALE 1/1 HELPFUL HINT : ...

  • Rubbermaid 5L20 - page 10

    Drill a pilot hole (using 1/8" drill bit) in front lower corner at location indicated by screw target. Note: This pilot hole is to be drilled through both walls. b . 3 . 4 W all Panel G Installation Align the lap joint between Repeat Left Side (C) and Front Left Side (G). c . Using a screwdriver , punch out the screw holes on the top of Front ...

  • Rubbermaid 5L20 - page 11

    Snap Front Left Side (G) into Front Floor (A) . d . 2 1 click ALIGN ALIGN G Install Wall Connector (Q) 5 places, connecting Repeat Left Side (C) and Front Left Side (G). Position connectors in slots and slide down to snap in place. e . 2 1 click OVERHEAD VIEW G G 1 Q C 3 . 5 W all Panel H Installation H H Screw Holes Using a screwdriver , punch out ...

  • Rubbermaid 5L20 - page 12

    Align the lap joint between Front Right Side (H) and Repeat Right Side (E). c . H Drill a pilot hole (using 1/8" drill bit) in front lower corner at location indicated by screw target. Note: This pilot hole is to be drilled through both walls. b . OVERHEAD VIEW DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B A ...

  • Rubbermaid 5L20 - page 13

    4 . 0 Roof Panel M (back position) Installation M RB Install one Repeat Roof (M) onto back section. The overlap edge of roof points toward the back of the shed. Align tongues on top of back wall to the outside of the roof panel overlap. Align tongues on top of side walls into grooves in roof. a . Slightly raise front edge of roof enough to allow po ...

  • Rubbermaid 5L20 - page 14

    From inside the shed, install four Screws (AA) into the roof, two on each side wall. Note: The screws also have to go through the Roof Brace (RB) at each end to properly secure the roof! A second person on the outside of the shed should hold down the edge of the roof firmly at each screw location. d . RB M AA (4) Ensure Repeat Roof (M) is position ...

  • Rubbermaid 5L20 - page 15

    4 . 2 Roof Panel J (front position) & Door Installation Install one Front Roof (J) onto front section: roof gable edge toward front of shed. Align tongues on top of side walls into grooves in roof. a . Slightly raise front edge of roof enough to allow positioning of Roof Brace (RB) onto the side walls as shown. Lower the roof onto the walls and ...

  • Rubbermaid 5L20 - page 16

    From inside the shed, install four Screws (AA) into the roof, two on each side wall. Note: The screws also have to go through the Roof Brace (RB) at each end to properly secure the roof! A second person on the outside of the shed should hold down the edge of the roof firmly at each screw location. e . Make sure Front Roof (J) is positioned tightly ...

  • Rubbermaid 5L20 - page 17

    5 . 0 Finishing Installation Install Screws (AA) into 8 locations shown at bottom of wall panels to secure walls to floor . a . AA (8) HELPFUL HINT : Pilot holes may be drilled for the screws. CAUTION: Do not overtighten screws. 5 . 1 Door Finishing Installation Install Lock Hasp (X) into opening on Right Door (K). a . Install Door Handle (T) onto ...

  • Rubbermaid 5L20 - page 18

    Printed in U.S.A. 2010 Rubbermaid Incorporated, Huntersville, NC U.S.A. 28078-1801 Customer Service T oll Free: 1-888-895-2110 M–F 8:30 a.m. to 5 p.m. EST or visit us at www .rubbermaid.com MAINTENANCE & SAFETY • Periodically check shed to assure it remains stable and the site remains level. • In areas of high winds it is recommended to a ...

Produzent Rubbermaid Kategorie Outdoor Storage

Dokumente, die wir vom Produzenten des Geräts Rubbermaid 5L20 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Rubbermaid
- Bedienungsanleitungen 5L20
- Produktkarten Rubbermaid
- Informationsbroschüren
- oder Energieetiketten Rubbermaid 5L20
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Rubbermaid 5L20.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Rubbermaid 5L20, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Rubbermaid 5L20. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Rubbermaid 5L20 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Rubbermaid 5L20, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Rubbermaid 5L20 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Rubbermaid 5L20 verständlich ist.

Eine gänzliche Bedienungsanleitung von Rubbermaid sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Rubbermaid 5L20 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Rubbermaid 5L20 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Rubbermaid 5L20, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Rubbermaid 5L20 - die uns die ersten Schritte während der Nutzung von Rubbermaid 5L20 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Rubbermaid 5L20 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Rubbermaid 5L20 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Rubbermaid 5L20?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Rubbermaid 5L20 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Rubbermaid 5L20 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)