English dropdown-ico

Manual Rubbermaid 5L20

18 pages 14.99 mb
Download

Go to site of 18

Summary
  • Rubbermaid 5L20 - page 1

    5L20 76 ¾" 51 ½" 55 ¼" 1780069 Note: Be sure to keep this instruction manual and your original store receipt to ensure our Consumer Service Department can accurately and quickly assist you if necessary . Congratulations and thank you for pur chasing a Rubbermaid storage building . BEFORE YOU BEGIN – BUILDING CODES Be sure to che ...

  • Rubbermaid 5L20 - page 2

    Description Part Number Assembly Letter Quantity Required T ools T wo Person Assembly Floor Front Floor 5L01 A 1 Repeat Floor 5L11 B 1 Walls Repeat Left Side 5L12 C 1 Left Back 5L04 D 1 Repeat Right Side 5L13 E 1 Right Back 5L05 F 1 Front Left Side 5L02 G 1 Front Right Side 5L03 H 1 Wall Connector 5H75 Q 15 Doors Left Door 5L06 / 5L41 L 1 Right Doo ...

  • Rubbermaid 5L20 - page 3

    Build a solid, level surface for the shed foundation. Consult your local building authority for ordinances, restrictions, or permits required before building any structure at your home. Note: Minimum dimensions for foundations shown. FLOOR PLAN: Size the construction site to fit the entire floor . OPTIONAL STEP: If desired, recessed anchor locati ...

  • Rubbermaid 5L20 - page 4

    A B 2 . 0 Floor Installation A Using a rubber mallet and screwdriver , knock out the tabs for the door hinge, 2 places on Front Floor (A) . c . Drill pilot hole through top sur face of floor , 2 places on Front Floor (A) . d . A Using a rubber mallet and screwdriver , punch out the screw holes along the connection edge of Repeat Floor (B) . a . B ...

  • Rubbermaid 5L20 - page 5

    A B 2 . 1 Floor Installation Connect and align Repeat Floor (B) to Front Floor (A) and install Screws (AA) 9 places; keep panels aligned and even while installing screws. a . AA (9) HELPFUL HINT : Pilot holes may be drilled for the screws using a 1/8" drill bit. CAUTION: Do not overtighten screws. 3 . 0 W all Panel C Installation Using a screw ...

  • Rubbermaid 5L20 - page 6

    3 . 1 W all Panel D Installation Snap Repeat Left Side (C) into the back position of Repeat Floor (B) . b . C ALIGN ALIGN click Hold Repeat Left Side (C) upright to prevent it from falling (until Left Back (D) is installed). c . C D D Using a screwdriver , punch out the screw holes on the top of Left Back (D) 4 places. a . Screw Holes ...

  • Rubbermaid 5L20 - page 7

    1 2 D C C OVERHEAD VIEW DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B AND 3-5_B SCALE 1/1 DETAIL 3-6_B AND 3-7_B SCALE 1/1 Connect Left Back (D) into dovetails of Repeat Left Side (C) . b . Engage snaps on bottom of Left Back (D) into Repeat Floor (B) . c . HELPFUL HINT : Lubricate dovetails with liquid soap. D 1 ...

  • Rubbermaid 5L20 - page 8

    Snap Repeat Right Side (E) into the back position of Repeat Floor (B) . b . Hold Repeat Right Side (E) upright to prevent it from falling (until Right Back (F) is installed). c . E ALIGN ALIGN click click 3 . 3 W all Panel F Installation Using a screwdriver , punch out the screw holes on the top of Right Back (F) 4 places. a . F F Screw Holes ...

  • Rubbermaid 5L20 - page 9

    Connect Right Back (F) onto dovetails of Repeat Right Side (E) . Align the lap joint between Left Back (D) and Right Back (F). b . Engage snaps on bottom of Right Back (F) into Repeat Floor (B) . c . DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B AND 3-5_B SCALE 1/1 DETAIL 3-6_B AND 3-7_B SCALE 1/1 HELPFUL HINT : ...

  • Rubbermaid 5L20 - page 10

    Drill a pilot hole (using 1/8" drill bit) in front lower corner at location indicated by screw target. Note: This pilot hole is to be drilled through both walls. b . 3 . 4 W all Panel G Installation Align the lap joint between Repeat Left Side (C) and Front Left Side (G). c . Using a screwdriver , punch out the screw holes on the top of Front ...

  • Rubbermaid 5L20 - page 11

    Snap Front Left Side (G) into Front Floor (A) . d . 2 1 click ALIGN ALIGN G Install Wall Connector (Q) 5 places, connecting Repeat Left Side (C) and Front Left Side (G). Position connectors in slots and slide down to snap in place. e . 2 1 click OVERHEAD VIEW G G 1 Q C 3 . 5 W all Panel H Installation H H Screw Holes Using a screwdriver , punch out ...

  • Rubbermaid 5L20 - page 12

    Align the lap joint between Front Right Side (H) and Repeat Right Side (E). c . H Drill a pilot hole (using 1/8" drill bit) in front lower corner at location indicated by screw target. Note: This pilot hole is to be drilled through both walls. b . OVERHEAD VIEW DETAIL 3-1_B SCALE 1/1 DETAIL 3-3_E SCALE 1/1 DETAIL 3-3_B SCALE 1/1 DETAIL 3-4_B A ...

  • Rubbermaid 5L20 - page 13

    4 . 0 Roof Panel M (back position) Installation M RB Install one Repeat Roof (M) onto back section. The overlap edge of roof points toward the back of the shed. Align tongues on top of back wall to the outside of the roof panel overlap. Align tongues on top of side walls into grooves in roof. a . Slightly raise front edge of roof enough to allow po ...

  • Rubbermaid 5L20 - page 14

    From inside the shed, install four Screws (AA) into the roof, two on each side wall. Note: The screws also have to go through the Roof Brace (RB) at each end to properly secure the roof! A second person on the outside of the shed should hold down the edge of the roof firmly at each screw location. d . RB M AA (4) Ensure Repeat Roof (M) is position ...

  • Rubbermaid 5L20 - page 15

    4 . 2 Roof Panel J (front position) & Door Installation Install one Front Roof (J) onto front section: roof gable edge toward front of shed. Align tongues on top of side walls into grooves in roof. a . Slightly raise front edge of roof enough to allow positioning of Roof Brace (RB) onto the side walls as shown. Lower the roof onto the walls and ...

  • Rubbermaid 5L20 - page 16

    From inside the shed, install four Screws (AA) into the roof, two on each side wall. Note: The screws also have to go through the Roof Brace (RB) at each end to properly secure the roof! A second person on the outside of the shed should hold down the edge of the roof firmly at each screw location. e . Make sure Front Roof (J) is positioned tightly ...

  • Rubbermaid 5L20 - page 17

    5 . 0 Finishing Installation Install Screws (AA) into 8 locations shown at bottom of wall panels to secure walls to floor . a . AA (8) HELPFUL HINT : Pilot holes may be drilled for the screws. CAUTION: Do not overtighten screws. 5 . 1 Door Finishing Installation Install Lock Hasp (X) into opening on Right Door (K). a . Install Door Handle (T) onto ...

  • Rubbermaid 5L20 - page 18

    Printed in U.S.A. 2010 Rubbermaid Incorporated, Huntersville, NC U.S.A. 28078-1801 Customer Service T oll Free: 1-888-895-2110 M–F 8:30 a.m. to 5 p.m. EST or visit us at www .rubbermaid.com MAINTENANCE & SAFETY • Periodically check shed to assure it remains stable and the site remains level. • In areas of high winds it is recommended to a ...

Manufacturer Rubbermaid Category Outdoor Storage

Documents that we receive from a manufacturer of a Rubbermaid 5L20 can be divided into several groups. They are, among others:
- Rubbermaid technical drawings
- 5L20 manuals
- Rubbermaid product data sheets
- information booklets
- or energy labels Rubbermaid 5L20
All of them are important, but the most important information from the point of view of use of the device are in the user manual Rubbermaid 5L20.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Rubbermaid 5L20, service manual, brief instructions and user manuals Rubbermaid 5L20. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Rubbermaid 5L20.

Similar manuals

A complete manual for the device Rubbermaid 5L20, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Rubbermaid 5L20 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Rubbermaid 5L20.

A complete Rubbermaid manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Rubbermaid 5L20 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Rubbermaid 5L20, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Rubbermaid 5L20, that we can find in the current document
3. Tips how to use the basic functions of the device Rubbermaid 5L20 - which should help us in our first steps of using Rubbermaid 5L20
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Rubbermaid 5L20
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Rubbermaid 5L20 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Rubbermaid 5L20?

Use the form below

If you did not solve your problem by using a manual Rubbermaid 5L20, ask a question using the form below. If a user had a similar problem with Rubbermaid 5L20 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)