Bedienungsanleitung Datalogic C-BOX 300

38 Seiten 6 mb
Download

Zur Seite of 38

Summary
  • Datalogic C-BOX 300 - page 1

    C-BOX 300/310 Installation Manual ...

  • Datalogic C-BOX 300 - page 2

    ...

  • Datalogic C-BOX 300 - page 3

    C-BOX 300/310 IN ST AL L ATI ON M ANU AL ...

  • Datalogic C-BOX 300 - page 4

    DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy C-BOX 300/310 Ed.: 03/2006 ALL RIGHTS RESERVED Datalogic S.p.A. reserves the right to make modifi cations and improvements without prior no tification. Datalogic shall not be liable fo r technical or editorial e rro rs or omissions contained herein, nor for incidental ...

  • Datalogic C-BOX 300 - page 5

    CONTENTS GUIDE TO INST ALLATION ........................................................................ iv GENERAL VIEW .......................................................................................... v SAFETY PRECA UTIONS ............................................................................ ix Power Supply ....................... ...

  • Datalogic C-BOX 300 - page 6

    GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessar y for complete installation of the C-BOX 3X0. 1) Rea d all information in the section "S afet y Precautions" at the beginning of this manual. 2) Correctly position a nd mount the C-BO X 3X0 within the reach of the barcode scanner cable, acco ...

  • Datalogic C-BOX 300 - page 7

    GENERAL VIEW C-BOX 300 2 3 4 1 Figure A 25-pin scanner connector Cove r screw s (4) Compre ssio n con nect ors 1 2 3 Prof ibus con nector 4 v ...

  • Datalogic C-BOX 300 - page 8

    C-BOX 310 2 1 Figure B LCD display Ke ypad 1 2 vi ...

  • Datalogic C-BOX 300 - page 9

    C-BOX 300/310 3 2 1 8 6 5 4 7 Figure C - Cover Inside LCD con trast tri mmer* 1 2 Power on LED 3 BUS activity LE D 4 Tx L ED 5 Module status LEDs 6 7 8 Configuration switch Node address select ors W arning LED * For 310 m odels only vii ...

  • Datalogic C-BOX 300 - page 10

    C-BOX 300/310 6 7 8 5 9 4 2 3 1 10 Figure D - Bottom Inside Pow er o n sw itch 1 2 S canner grounding selec tor 3 S pring clam p term inal blocks 5 4 GET button TEST button 6 SEND button 7 8 A uxiliary port connecto r OM4000 jumper s 9 W arning LED 10 Power polarity error LED vii i ...

  • Datalogic C-BOX 300 - page 11

    SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT - This product is intended to be installed by Qualified Personn el only. The C-BOX 3X0 is intend ed to be supplied either by a UL Listed NEC Cl ass 2 power source, or a UL Listed ITE Limited Po wer Source (LPS), rated 10-30 V dc, minimum 0.5 A. See par. 2 ...

  • Datalogic C-BOX 300 - page 12

    Terminating Resistors Terminating resist ors must be us ed if the C-BOX is installed at the begin ning or end of the PROFIBUS cable segment. In this case, it is recommende d to use PROFIBUS connectors which contain an integrate d terminating resistor. It is recommended to use connectors from ERNI and Siemens. If the bus is inc orrectly terminated, ...

  • Datalogic C-BOX 300 - page 13

    GENERAL FEATURES 1 1 GENERAL FEATURES 1.1 DESCRIPTION The C-BOX 3X0 is a c onnection box whic h converts RS232 communications t o Profibus. It is available in two models: C-BOX 300, without display, C-BOX 310, with LCD display. It can be used as an accessory of the Datalogic scanner s to perform the following functions: • Connect an RS232 scanner ...

  • Datalogic C-BOX 300 - page 14

    C-BOX 300/310 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 3 X0 and all the parts supplied w ith the equipm ent are present and intact when opening the packagin g; the list of parts includes: 1) C-BOX 3X0 2) Installation manual 3) C-BOX 3X0 configuration CD- ROM 4) 2 mounting screws 3 1 2 4 Figure 1 - C-BOX 3X0 Package Contents 2 ...

  • Datalogic C-BOX 300 - page 15

    INSTALLATION 2 2.2 OPENING THE DEVICE To install the C-BOX 3 X0 or during normal ma intenance, it is necessary to open it b y unscrewing the four cover screws: CA UTIO N The C-BOX 3X0 must be disconnected from the power supply during this operation. Figure 2 - Opening t he C-BOX 3X0 It is possible to perform the following operations: • Proceed wi ...

  • Datalogic C-BOX 300 - page 16

    C-BOX 300/310 2 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimens i ons of the C-BOX 3X0 and m ay be used for its installation. = 165 [6.48] 90 [3.54] 60 [2.36] 99 [3.88] 115 [4.53] 66 [2.60] 150 [5.91] = = = Ø3 [Ø0.14] n°2 mm inch Figure 3 - Overall Dimensions 4 ...

  • Datalogic C-BOX 300 - page 17

    INSTALLATION 2 C-BOX 3X0 can be installed to operate in different positions. The two screw holes inside the housing of the C-B OX 3X0 ar e for mechanical fixture (Figure 4). To mount the C-BOX 3X0: 1) Open the C-BOX 3X0 by unscre wing the 4 cover screws. If necessary, using the two mounting holes insi de the device as a pattern, mark the pan el wit ...

  • Datalogic C-BOX 300 - page 18

    C-BOX 300/310 2 2.4 ELECTRICAL CONNECTIONS AN D HARDWARE SETUP The following figure shows the typical layout. PROFIBUS MASTER C-BOX 3X0 SCANNER System Cables Figure 5 – System La yout NOTE Matrix readers are not compatible w ith the WinHost configuration program. For Matrix reader setup first read par. 2.9 for det ails. A PC can be connected t o ...

  • Datalogic C-BOX 300 - page 19

    INSTALLATION 2 NOTE Autoconnection is not c ompatible with Matrix readers and must be disabled in the C-BOX 3x0 confi guration. Se e par. 2.9 for details. To disable this automatic connection pr oc edure, refer to Wi nHost Help Online. After system functioning has been verified, close the C-BOX 3X0 using the 4 cov er screws making sure the rubber s ...

  • Datalogic C-BOX 300 - page 20

    C-BOX 300/310 2 NOTE Pin 1 is also electrical ly connected to pins 3 and 5, just as pin 2 is electrically connected to pins 4 and 6. This is useful for external trigger/inputs connections. WA RN ING Incorrect grounding of the C-BOX 3X0 can in jure personnel and damage equipment. Make su re that the C-BOX is correctly grounded. NOTE The C-BOX 3X0 is ...

  • Datalogic C-BOX 300 - page 21

    INSTALLATION 2 2.4.2 System Wiring The connection and wiring pr ocedure for C-BOX 3X0 is described as follows: 1) Open the C-BOX 3X0 as de s cribed in paragraph 2.2. 2) Verify that the C-BOX 3X0 power switch is off (see Figure 6). 3) Unscrew the compression connectors and pass all the system cables through them into t he C-BOX 3X0 housing. 4) To co ...

  • Datalogic C-BOX 300 - page 22

    C-BOX 300/310 2 The C-BOX 3X0 spring clamp connector pi nout s are indicated in the follo wing table. Refer to the scanner Insta llation Manual for details. Pin Name 1, 3, 5 VS 2, 4, 6 GND 7, 8 EARTH GROUND 9…12, 20, 33, 34, 40 Reserved 35 TXA 37 RXA DS2100A DS2400A DS4600A Matrix-2000™ Matrix-1000™ 21 OUT1+ OUT1+ OUT1+ NC 22 OUT REF OUT1- OU ...

  • Datalogic C-BOX 300 - page 23

    INSTALLATION 2 2.4.3 Scanner Chassis Grounding Jumper Settings The scanner chassis grounding method can be selected by positioning a jumper (see Figure 9). In this w ay the scanner c hassis can be connected to earth gr ound (only if pins 7 or 8 are connecte d to a good earth ground) or to the po wer supply ground signal. The scanner chass is can al ...

  • Datalogic C-BOX 300 - page 24

    C-BOX 300/310 2 2.5 PROFIBUS CONNECTIONS AND SETUP 2.5.1 Profibus Node Address Selection To interface the C-BOX 3X0 with a Profib us network, the Node Address should be set using the rotary switches placed in th e cover inside. The valid address range is from 000 to 126. If an invalid value is detect ed, the C-BOX can not communi cate with the Prof ...

  • Datalogic C-BOX 300 - page 25

    INSTALLATION 2 9-pin external female c onnector pinout Pin Name Function 1 N.C. not connected 2 N.C. not connected 3 B-LINE (RS485+) 4 RTS Ready To Send 5 GND RS485 Bus Reference 6 + 5V (galvanically isolated) RS485 Bus Power Supply 7 N.C. not connected 8 A-Line (RS485-) 9 N.C. not connected 2.5.3 Connection to a Profibus Network The following figu ...

  • Datalogic C-BOX 300 - page 26

    C-BOX 300/310 2 To ensure that the C-BO X functions without errors, the shield of the PROFIBUS cable must be grounded. – Ensure that the PROFIBUS connector uses the pi n assignments shown in par 2.5.2 – Attach the PROFIBUS connector to the PROFIBUS interface socket on the C-BOX 3X0 and secure the connector with the retaining screws. – For C-B ...

  • Datalogic C-BOX 300 - page 27

    INSTALLATION 2 2.6 CONFIGURATION SWITCH AND 9-PIN INTERNAL CONNECTOR The 9-pin internal c onnector may have t wo different functions according to the position of the conf iguration s witch. Figure 13 - Configurati on Switch and 9-pin Mal e Connector POSITION MODE Normal Operation (default): In this position, the C-BOX 3X0 is in the normal operating ...

  • Datalogic C-BOX 300 - page 28

    C-BOX 300/310 2 POSITION MODE CFG : When the switch is in this position, the C-BOX 3X0 is in configuration mode. The communicati on with the scanner is interrupted and pins 2 and 3 ar e no longer dedicated to the scan ner auxiliary interface but to the C-BOX 3X0 c onfiguration (see tab le below). The system enters configuration mode and waits to be ...

  • Datalogic C-BOX 300 - page 29

    INSTALLATION 2 2.7 SCANNER REQUIREMENTS The C-BOX 3X0 can be connecte d to the following scanners through the 25-pin connector illustrated in Figure A. DS2100A DS4600A *Matrix-2000™ DS2400A *Matrix-1000™ 1) For all scanners, it is neces sary to use the RS232 inter face which must be selected by the user . 2) At least one Terminator Character sh ...

  • Datalogic C-BOX 300 - page 30

    C-BOX 300/310 2 2.8.1 GET/TEST/SEND Functions The C-BOX 300 has three internal function buttons. In th e C-BOX 310, they are also available on the cover, and their function is indicated o n the display. C-BOX 300 GET TE ST SEND C-BOX 310 Figure 14 – Internal Functi on Buttons NOTE The GET/TEST/SEND function is not co mpatible with Matrix readers. ...

  • Datalogic C-BOX 300 - page 31

    INSTALLATION 2 GET – (left button): the C-BOX 3X0 reads th e curr ent scanner configuration and permanently copies it in its own memory support (EEPRO M). The C-BOX 3X0 preserves this configuration also when switched off. TEST - (center button ): the C-BOX 3X0 forc es the scanner to run the Test Operating Mode (refer to the scanner I nstallation ...

  • Datalogic C-BOX 300 - page 32

    C-BOX 300/310 2 2.8.2 LED Indicators Figure 15 - LED Indicators TX L ED MS LEDs Warning LED BUS activity Power on In the C-BOX 3X0 the Warning LED is repeated in the b ottom inside. Warning LED Power polarity error LED Figure 16 – Warning LED 20 ...

  • Datalogic C-BOX 300 - page 33

    INSTALLATION 2 The internal LEDs of the C-BOX 3X0 (see Fig ure 15) indicate the following: POWER ON ( PWR ) (red) indicates the C-BOX 3X0 is connected to the power supply and the power switch is ON. WARNIN G ( WL ) (red) indicates a wa rning or e rror condition. It is ON when a connection procedure is i n progress (the system is busy), during a GET ...

  • Datalogic C-BOX 300 - page 34

    C-BOX 300/310 2 2.9 SPECIAL NOTES FOR MATRIX RE ADER SETUP CAUTION When connected to a C-BOX 3x0 through the 25-pin connector , the 9-pin Auxiliary port co nnector on the Matrix reader ca nnot be used for communication (i.e. config uration through VisiSet™). The Matrix reader can only be configured th roug h the 9-pin connector inside the C-BOX 3 ...

  • Datalogic C-BOX 300 - page 35

    INSTALLATION 2 2.9.2 Matrix Reader Configuration Using VisiSet™ After performing C-Box 3x0 config uration as described in the previo us paragraph, the Matrix reader can be co nfigured through the C-Bo x 3x0 9-pin internal connector connected to the PC using the Vi siSet™ configuration program: 1. Run the VisiSet™ configurat ion tool and selec ...

  • Datalogic C-BOX 300 - page 36

    C-BOX 300/310 2 Figure 18 – WinHost Configurat ion Menu for C-Box 3x0 6. Close the C-BOX 300. 24 ...

  • Datalogic C-BOX 300 - page 37

    TECHNICAL FEATURES 3 3 TECHNICAL FEATURES ELECTRICAL FEATURES C-BOX 300 C-BOX 310 Power Supply voltage 10 to 30 Vdc Power consumption max. 2.9 W + scanner 4.7 W + scanner USER INTERFACE LED indicators Pow er O N, W arn ing , Tx, Diagnostics PHYSICAL FEATURES Mechanical dimensions 167 x 115 x 61 m m (6.57 x 4.53 x 2.40 in.) W e i g h t about 440 g. ...

  • Datalogic C-BOX 300 - page 38

    DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy 05 dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el C-BOX-3X0 e tutti i suoi mo delli and all its models et tous ses modèle s und seine Modelle y todos sus mo delos sono conformi alle Direttive del Consig lio Europeo sottoel encate ...

Produzent Datalogic Kategorie Scanner

Dokumente, die wir vom Produzenten des Geräts Datalogic C-BOX 300 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Datalogic
- Bedienungsanleitungen C-BOX 300
- Produktkarten Datalogic
- Informationsbroschüren
- oder Energieetiketten Datalogic C-BOX 300
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Datalogic C-BOX 300.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Datalogic C-BOX 300, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Datalogic C-BOX 300. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Datalogic C-BOX 300 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Datalogic C-BOX 300, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Datalogic C-BOX 300 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Datalogic C-BOX 300 verständlich ist.

Eine gänzliche Bedienungsanleitung von Datalogic sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Datalogic C-BOX 300 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Datalogic C-BOX 300 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Datalogic C-BOX 300, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Datalogic C-BOX 300 - die uns die ersten Schritte während der Nutzung von Datalogic C-BOX 300 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Datalogic C-BOX 300 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Datalogic C-BOX 300 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Datalogic C-BOX 300?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Datalogic C-BOX 300 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Datalogic C-BOX 300 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)