Bedienungsanleitung Jensen JKRS3

16 Seiten 0.38 mb
Download

Zur Seite of 16

Summary
  • Jensen JKRS3 - page 1

    128-7052 1 of 16 Kit Contents (1) Control Module (1) 3 Button High Frequency Transmitters (1) 5 Button Two Way LED Based Transceiver (1) On Glass Mount Superheterodyne Transceiver (1) Multi Pin Input/Output Harness (1) Six Pin Power Harness (1) Diesel Wait To Start Input (1) Auxiliary 4 Pin Output Harness (1) 2 Pin Door Lock Harness (2) 30 Amp In-l ...

  • Jensen JKRS3 - page 2

    128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the ...

  • Jensen JKRS3 - page 3

    128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some n ...

  • Jensen JKRS3 - page 4

    128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition ...

  • Jensen JKRS3 - page 5

    128-7052 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self-tapping screw and ring terminal. BLACK w/WHITE TRACER WIRE: Control Swit ...

  • Jensen JKRS3 - page 6

    128-7052 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...

  • Jensen JKRS3 - page 7

    128-7052 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a external relay . Connect terminal #85 of the relay to ...

  • Jensen JKRS3 - page 8

    128-7052 8 of 16 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start u ...

  • Jensen JKRS3 - page 9

    128-7052 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circui ...

  • Jensen JKRS3 - page 10

    128-7052 10 of 16 10 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and o ...

  • Jensen JKRS3 - page 11

    128-7052 11 of 16 11 c. Immediately turn the ignition key OFF. d. Hold the program switch ON, then start the vehicle using the ignition key . e. When the unit senses the tach signal, the parking lights will begin to flash. 6. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored and the ...

  • Jensen JKRS3 - page 12

    128-7052 12 of 16 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit. W ARNING!! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE HOOD PIN SAFETY SHUT DOWN FEA TURE. MANUAL SHU ...

  • Jensen JKRS3 - page 13

    128-7052 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanic ...

  • Jensen JKRS3 - page 14

    128-7052 14 of 16 14 such as the light on reminder . These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the consumer . Circuits may be used only if the above circuit is not available. T o connect to the key in sensor as shown in method 1: 1.Locate the control wire that connects t ...

  • Jensen JKRS3 - page 15

    128-7052 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the ...

  • Jensen JKRS3 - page 16

    128-7052 16 of 16 © 2004 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7052 ...

Produzent Jensen Kategorie Remote Starter

Dokumente, die wir vom Produzenten des Geräts Jensen JKRS3 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Jensen
- Bedienungsanleitungen JKRS3
- Produktkarten Jensen
- Informationsbroschüren
- oder Energieetiketten Jensen JKRS3
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Jensen JKRS3.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Jensen JKRS3, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Jensen JKRS3. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Jensen JKRS3 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Jensen JKRS3, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Jensen JKRS3 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Jensen JKRS3 verständlich ist.

Eine gänzliche Bedienungsanleitung von Jensen sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Jensen JKRS3 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Jensen JKRS3 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Jensen JKRS3, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Jensen JKRS3 - die uns die ersten Schritte während der Nutzung von Jensen JKRS3 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Jensen JKRS3 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Jensen JKRS3 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Jensen JKRS3?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Jensen JKRS3 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Jensen JKRS3 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)