Manuel d’utilisation Jensen JKRS3

16 pages 0.38 mb
Télécharger

Aller à la page of 16

Summary
  • Jensen JKRS3 - page 1

    128-7052 1 of 16 Kit Contents (1) Control Module (1) 3 Button High Frequency Transmitters (1) 5 Button Two Way LED Based Transceiver (1) On Glass Mount Superheterodyne Transceiver (1) Multi Pin Input/Output Harness (1) Six Pin Power Harness (1) Diesel Wait To Start Input (1) Auxiliary 4 Pin Output Harness (1) 2 Pin Door Lock Harness (2) 30 Amp In-l ...

  • Jensen JKRS3 - page 2

    128-7052 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the ...

  • Jensen JKRS3 - page 3

    128-7052 3 of 16 3 THE TRANSCEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Transceiver Antenna Assembly provided with this unit allows routing from below the dash- board for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some n ...

  • Jensen JKRS3 - page 4

    128-7052 4 of 16 Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FURTHER DET AILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition ...

  • Jensen JKRS3 - page 5

    128-7052 5 of 16 WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self-tapping screw and ring terminal. BLACK w/WHITE TRACER WIRE: Control Swit ...

  • Jensen JKRS3 - page 6

    128-7052 6 of 16 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle. This wire provides a + 12 Volt output when the ignition key is turned to the “ON” position, and 0 Vol ...

  • Jensen JKRS3 - page 7

    128-7052 7 of 16 7 A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a external relay . Connect terminal #85 of the relay to ...

  • Jensen JKRS3 - page 8

    128-7052 8 of 16 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start u ...

  • Jensen JKRS3 - page 9

    128-7052 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circui ...

  • Jensen JKRS3 - page 10

    128-7052 10 of 16 10 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and o ...

  • Jensen JKRS3 - page 11

    128-7052 11 of 16 11 c. Immediately turn the ignition key OFF. d. Hold the program switch ON, then start the vehicle using the ignition key . e. When the unit senses the tach signal, the parking lights will begin to flash. 6. Release the program switch. The parking lights will turn on for 3 seconds to indicate that the tach signal is stored and the ...

  • Jensen JKRS3 - page 12

    128-7052 12 of 16 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of the Audiovox Remote Start Unit. W ARNING!! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE HOOD PIN SAFETY SHUT DOWN FEA TURE. MANUAL SHU ...

  • Jensen JKRS3 - page 13

    128-7052 13 of 16 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanic ...

  • Jensen JKRS3 - page 14

    128-7052 14 of 16 14 such as the light on reminder . These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the consumer . Circuits may be used only if the above circuit is not available. T o connect to the key in sensor as shown in method 1: 1.Locate the control wire that connects t ...

  • Jensen JKRS3 - page 15

    128-7052 15 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the ...

  • Jensen JKRS3 - page 16

    128-7052 16 of 16 © 2004 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-7052 ...

Fabricant Jensen Catégorie Remote Starter

Les documents que nous recevons du fabricant de l'appareilJensen JKRS3 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Jensen
- manuels d’utilisations JKRS3
- fiches produit Jensen
- dépliants
- ou étiquettes-énergie Jensen JKRS3
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Jensen JKRS3.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Jensen JKRS3, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Jensen JKRS3. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Jensen JKRS3.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Jensen JKRS3, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Jensen JKRS3 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Jensen JKRS3.

Le manuel d’utilisation complet Jensen, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Jensen JKRS3 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Jensen JKRS3, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lJensen JKRS3 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Jensen JKRS3 - qui devraient nous aider dans les premières étapes lors de l'utilisation Jensen JKRS3
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Jensen JKRS3
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Jensen JKRS3 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Jensen JKRS3?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Jensen JKRS3, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Jensen JKRS3 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)