Bedienungsanleitung Thermo Products USDT2004

14 Seiten 0.5 mb
Download

Zur Seite of 14

Summary
  • Thermo Products USDT2004 - page 1

    USDT 2004 Installation and User’s Guide Introduction General Information 2 Installation 3 Collector Sensor 3 Control Box 5 Power Connection 6 Display Window 6 Operation Basic Operation (Factory Setting for Only Two Sen sors) 7 Manual Operation Mode 8 Three Sensor Operation 9 Sensor Selection 11 Alarm Functions and Diagnostics 12 Energy Calculatio ...

  • Thermo Products USDT2004 - page 2

    2 Introduction Note: The information supplied in this manual is for guidance only - no part of this may be used for any agreement, whether express or implied, or to form any contract. Thermo Technologies reserves the right to change specifications without prior notice. SDT 2004 is a powerful temperature differential control unit. It has *two progra ...

  • Thermo Products USDT2004 - page 3

    3 INSTALLATION Note: This installation procedure is for guidance only, and the installer should verify its suitability. Make sure that the solar system is physically installed, manually tested, and ready for controlled operation. he following sa fety precautions are strongly recommended: 1. Before attempting to install and operate the unit read thi ...

  • Thermo Products USDT2004 - page 4

    4 strap the sensor to the collector outl et pipe or the absorber (flat plate collectors) that projects from the collector housing. Ideally, house the collector sensor (encased in a suitable sensor pocket) into a T - piece on the collector return outlet. Protect the sensor cable from UV and moistur e. l Return (tank) sensor (white cable): The sensor ...

  • Thermo Products USDT2004 - page 5

    5 Undo the screw at the top of the housing. The control electronics are mounted on the enclosure cover. The controller enclosure can be screwed to the wall with cable entry grommets pointed downwards. Use the supplied plastic bridges to secure pow er and sensor cables. Base of the unit to be mounted at eye - level and wired as shown above Caution: ...

  • Thermo Products USDT2004 - page 6

    6 ower Connections: A small blade screwdriver may be used to fasten miniaturized terminal block screws while the corresponding wire is inse rted. NOTE 1: Always disconnect the controller from power supply before opening the housing. NOTE 2: The controller should be properly grounded. Flexible wires, 18/3 AWG (gauge/conductor) simplify connection to ...

  • Thermo Products USDT2004 - page 7

    7 Use selection keys ïð during normal system operation to display the desired parameter: T1 xxx Collector temperature in o F T2 xxx Tank temperature in o F T3 xxx Reading of the third sensor; if the third sensor is not used it displays a fixed reference temperature of 250 o F XX xxx Collector power in [kW] YY xxx Energy collected in [MWh] ZZ xxx ...

  • Thermo Products USDT2004 - page 8

    8 RUV X.X – This display shows the software revision number. NR O – This is PROGRAM 0 which indicates simple operation of unit as a U niversal S olar D ifferential T emperature ( USDT ) controller. Change this value to 1 ( NR 1 ) for activation of the third sensor or puls e flow meter input (PROGRAM 1) . Hysteresis Bandwidth User can program hy ...

  • Thermo Products USDT2004 - page 9

    9 symbol while the pump is running. User can switch to manual mode by pressing ò k ey. By pressing ð key while centerline blinks, a hand symbol G in lower line shows manual operation. Pressing ð one more time lets you turn the pump ON or OFF . By pressing ñ key you change the pump operation. Advanced Operation (Setting for Three Sensors and Flo ...

  • Thermo Products USDT2004 - page 10

    10 max = 2 Pump runs again below this set point (T3) Energy calculation mode (PROGRAM 1) : USDT 2004 computes the energy production as a function of the temperature diff erential and fluid volume. In addition, the system anti - freeze (Glycol) percentage should be entered as it affects the thermal conductivity and heat transfer rate. Press the Adva ...

  • Thermo Products USDT2004 - page 11

    11 START Starts pump at pre - set insolation (solar radiation intensity) ALARM Enables/Disables protection functions BTU Energy calculation and setting ensor Designation – USD T 2004 accepts two different sensor types or a reference value . User can program a constant reference temperature instead of a sensor output. The factory - preset sensor i ...

  • Thermo Products USDT2004 - page 12

    12 circulation pump runs when the collector temperature is below a programmable minimum temperature, shown by = symbol. The pump stops as soon as the temperature in the solar loop reaches a safe region programmed by the ? symbol. This feature is also disabled at the factory by entering - 4 o F. min = Pump runs below this temperature min ? Pump stop ...

  • Thermo Products USDT2004 - page 13

    13 2 OPEN Disconnection in sensor 2 wiring OK System operates normal NO CIRC r T is more than 108 o F in last 30 minutes OK CIRC Pump is running CLEAR Clears NO CIRC display after correction nergy calculation - Energy gain is calculated by obtaining the temperature increase of heat transfer fluid across the solar collector. The amount of fluid flow ...

  • Thermo Products USDT2004 - page 14

    14 T roubleshooting In general, all of the settings in the menus Par and Men and the terminal should f irst be checked if there is a malfunction. Malfunction, but "realistic" temperature values: • Check program number. • Check the switch - on and switch - off thresholds and the set differential temperatures. Have the thermostat and di ...

Produzent Thermo Products Kategorie Stud Sensor

Dokumente, die wir vom Produzenten des Geräts Thermo Products USDT2004 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Thermo Products
- Bedienungsanleitungen USDT2004
- Produktkarten Thermo Products
- Informationsbroschüren
- oder Energieetiketten Thermo Products USDT2004
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Thermo Products USDT2004.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Thermo Products USDT2004, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Thermo Products USDT2004. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Thermo Products USDT2004 ansehen.

Die komplette Bedienungsanleitung des Geräts Thermo Products USDT2004, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Thermo Products USDT2004 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Thermo Products USDT2004 verständlich ist.

Eine gänzliche Bedienungsanleitung von Thermo Products sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Thermo Products USDT2004 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Thermo Products USDT2004 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Thermo Products USDT2004, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Thermo Products USDT2004 - die uns die ersten Schritte während der Nutzung von Thermo Products USDT2004 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Thermo Products USDT2004 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Thermo Products USDT2004 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Thermo Products USDT2004?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Thermo Products USDT2004 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Thermo Products USDT2004 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)