Thermo Products USDT2004の取扱説明書

14ページ 0.5 mb
ダウンロード

ページに移動 of 14

Summary
  • Thermo Products USDT2004 - page 1

    USDT 2004 Installation and User’s Guide Introduction General Information 2 Installation 3 Collector Sensor 3 Control Box 5 Power Connection 6 Display Window 6 Operation Basic Operation (Factory Setting for Only Two Sen sors) 7 Manual Operation Mode 8 Three Sensor Operation 9 Sensor Selection 11 Alarm Functions and Diagnostics 12 Energy Calculatio ...

  • Thermo Products USDT2004 - page 2

    2 Introduction Note: The information supplied in this manual is for guidance only - no part of this may be used for any agreement, whether express or implied, or to form any contract. Thermo Technologies reserves the right to change specifications without prior notice. SDT 2004 is a powerful temperature differential control unit. It has *two progra ...

  • Thermo Products USDT2004 - page 3

    3 INSTALLATION Note: This installation procedure is for guidance only, and the installer should verify its suitability. Make sure that the solar system is physically installed, manually tested, and ready for controlled operation. he following sa fety precautions are strongly recommended: 1. Before attempting to install and operate the unit read thi ...

  • Thermo Products USDT2004 - page 4

    4 strap the sensor to the collector outl et pipe or the absorber (flat plate collectors) that projects from the collector housing. Ideally, house the collector sensor (encased in a suitable sensor pocket) into a T - piece on the collector return outlet. Protect the sensor cable from UV and moistur e. l Return (tank) sensor (white cable): The sensor ...

  • Thermo Products USDT2004 - page 5

    5 Undo the screw at the top of the housing. The control electronics are mounted on the enclosure cover. The controller enclosure can be screwed to the wall with cable entry grommets pointed downwards. Use the supplied plastic bridges to secure pow er and sensor cables. Base of the unit to be mounted at eye - level and wired as shown above Caution: ...

  • Thermo Products USDT2004 - page 6

    6 ower Connections: A small blade screwdriver may be used to fasten miniaturized terminal block screws while the corresponding wire is inse rted. NOTE 1: Always disconnect the controller from power supply before opening the housing. NOTE 2: The controller should be properly grounded. Flexible wires, 18/3 AWG (gauge/conductor) simplify connection to ...

  • Thermo Products USDT2004 - page 7

    7 Use selection keys ïð during normal system operation to display the desired parameter: T1 xxx Collector temperature in o F T2 xxx Tank temperature in o F T3 xxx Reading of the third sensor; if the third sensor is not used it displays a fixed reference temperature of 250 o F XX xxx Collector power in [kW] YY xxx Energy collected in [MWh] ZZ xxx ...

  • Thermo Products USDT2004 - page 8

    8 RUV X.X – This display shows the software revision number. NR O – This is PROGRAM 0 which indicates simple operation of unit as a U niversal S olar D ifferential T emperature ( USDT ) controller. Change this value to 1 ( NR 1 ) for activation of the third sensor or puls e flow meter input (PROGRAM 1) . Hysteresis Bandwidth User can program hy ...

  • Thermo Products USDT2004 - page 9

    9 symbol while the pump is running. User can switch to manual mode by pressing ò k ey. By pressing ð key while centerline blinks, a hand symbol G in lower line shows manual operation. Pressing ð one more time lets you turn the pump ON or OFF . By pressing ñ key you change the pump operation. Advanced Operation (Setting for Three Sensors and Flo ...

  • Thermo Products USDT2004 - page 10

    10 max = 2 Pump runs again below this set point (T3) Energy calculation mode (PROGRAM 1) : USDT 2004 computes the energy production as a function of the temperature diff erential and fluid volume. In addition, the system anti - freeze (Glycol) percentage should be entered as it affects the thermal conductivity and heat transfer rate. Press the Adva ...

  • Thermo Products USDT2004 - page 11

    11 START Starts pump at pre - set insolation (solar radiation intensity) ALARM Enables/Disables protection functions BTU Energy calculation and setting ensor Designation – USD T 2004 accepts two different sensor types or a reference value . User can program a constant reference temperature instead of a sensor output. The factory - preset sensor i ...

  • Thermo Products USDT2004 - page 12

    12 circulation pump runs when the collector temperature is below a programmable minimum temperature, shown by = symbol. The pump stops as soon as the temperature in the solar loop reaches a safe region programmed by the ? symbol. This feature is also disabled at the factory by entering - 4 o F. min = Pump runs below this temperature min ? Pump stop ...

  • Thermo Products USDT2004 - page 13

    13 2 OPEN Disconnection in sensor 2 wiring OK System operates normal NO CIRC r T is more than 108 o F in last 30 minutes OK CIRC Pump is running CLEAR Clears NO CIRC display after correction nergy calculation - Energy gain is calculated by obtaining the temperature increase of heat transfer fluid across the solar collector. The amount of fluid flow ...

  • Thermo Products USDT2004 - page 14

    14 T roubleshooting In general, all of the settings in the menus Par and Men and the terminal should f irst be checked if there is a malfunction. Malfunction, but "realistic" temperature values: • Check program number. • Check the switch - on and switch - off thresholds and the set differential temperatures. Have the thermostat and di ...

メーカー Thermo Products カテゴリー Stud Sensor

Thermo Products USDT2004のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- USDT2004の取扱説明書
- Thermo Productsの製品カード
- パンフレット
- またはThermo Products USDT2004の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Thermo Products USDT2004の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Thermo Products USDT2004の取り付け説明書、サービスマニュアル、簡易説明書、またはThermo Products USDT2004のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Thermo Products USDT2004の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Thermo Products USDT2004デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがThermo Products USDT2004を使用するのを助ける技術的文書のことです。説明書は通常、全てのThermo Products USDT2004ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Thermo Productsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Thermo Products USDT2004の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははThermo Products USDT2004の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Thermo Products USDT2004に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Thermo Products USDT2004デバイスの基本機能を使うにあたってのヒント。 Thermo Products USDT2004のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Thermo Products USDT2004に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるThermo Products USDT2004のメーカー/サービスへの連絡先に関する情報。

Thermo Products USDT2004についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもThermo Products USDT2004の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがThermo Products USDT2004で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)