Bedienungsanleitung Xantech 490-85

10 Seiten 0.26 mb
Download

Zur Seite of 10

Summary
  • Xantech 490-85 - page 1

    08905105A - 1 - INSTALLATION INSTRUCTIONS 490-85 CLF / LCD Friendly Micr o Link IR Receiver DESCRIPTION The 490-85 is a CFL (compact fluoresc ent light) / LCD (liquid crystal di splay) version of the 490 Micro Link series IR receivers. It is specifically designed to have greater i mmunity to high frequency ballasted CFL and overhead fluorescent typ ...

  • Xantech 490-85 - page 2

    08905105A - 2 - IR CARRIER ADJUSTMENT The 490-85 is factory set to an IR carrier repeat frequency of 39kHz . This will be correct for the majority of installations. Howe ver, some manufacturer’s components that you wish to control may use different carrier frequencies (such as RCA DSS satell ite receivers that use 56kHz). If sure carrier frequenc ...

  • Xantech 490-85 - page 3

    08905105A - 3 - APPLICATION WIRING A typical system, with a 490-85, 781RG Power S upply and 283M Emitters plugged into a 791-44 Connecting Block, is shown in the figure below. 1. Plug the 3.5 mm stereo mini plug from the 490-85 into the 791-44 connecting block labeled “IR RCVR”. 2. Plug in the 3.5 mm mono mini plug from any of the 282, 284, 283 ...

  • Xantech 490-85 - page 4

    08905105A - 4 - IR Troubleshooting Guide NOTE: Due to the many variables in a given installa tion, the troubleshooting counter measures you will have to take may vary from job to job. Each insta llation is different due to the number of IR receivers in use, length of wire runs, type of wire, amount of ambient IR noise present, etc…. Therefore, yo ...

  • Xantech 490-85 - page 5

    08905105A - 5 - Symptom #2: TB LED on IR Receiver (and/or Emitters) Dimly lit or flickering Cause: Solution 1. Signal and ground wir es are reversed or shorted either at the connecting block or IR receiver. Recheck your wiring. 2. Defective emitter. Replace Emitter 3. Relatively high levels of ambient noise . This can be due to any of the following ...

  • Xantech 490-85 - page 6

    08905105A - 6 - Symptom #3: TB LED on IR Receiver (and/or Emitters) on solid Cause: Solution 1. Plasma Interference Use a 490-90 Plasma 'Friendly' Receiver. If already using a 490-90 unit, please note the Plasma interference can be reflected off of any item it comes into contact with within approx. 3ft. From the front of the display. Keep ...

  • Xantech 490-85 - page 7

    08905105A - 7 - Symptom #4: TB LED on IR Rec. blinks but 283M or 286M 'Blink' style Emitters do not Cause: Solution 1. There may be a short, such as a staple driven through the Signal and GND wires of the IR Receiver and/or the emitter. Recheck your wiring. 2. Emitter may be shorted internally Replace Emitter or use TEST EMITTER to check ...

  • Xantech 490-85 - page 8

    08905105A - 8 - Symptom 6: Emitters function but some (or all) components do not respond. Cause: Solution 1. Emitter placement is incorrect. Reposition the Emitter so that it is directly over the components sensor window. Consult the components owners manual of the unit for the exact location of the IR Sensor Window. 2. Emitter placement is correct ...

  • Xantech 490-85 - page 9

    08905105A - 9 - Symptom #7: Absolutely No Functionality (How to determine which component is at fault) Step: Component to Test Instructions 1. Verify Power Supply With a Multimeter, measure the DC Voltage of the supply while it is connected to the Connecting Block. Put the Negative lead of the meter on the terminal marked GND and the Positive Lead ...

  • Xantech 490-85 - page 10

    08905105A - 10 - 4. Verify IR Receiver. Remove the power supply from the connecting block and all Emitters from the output. Place a jumper wire on the connecting block between IR Signal and GND. Reconnect the Power Supply. With a known good hand-held remote, shoot a constant IR Command at the receiver and verify the TB LED on the Receiver lights. X ...

Produzent Xantech Kategorie Radio

Dokumente, die wir vom Produzenten des Geräts Xantech 490-85 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Xantech
- Bedienungsanleitungen 490-85
- Produktkarten Xantech
- Informationsbroschüren
- oder Energieetiketten Xantech 490-85
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Xantech 490-85.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Xantech 490-85, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Xantech 490-85. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Xantech 490-85 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Xantech 490-85, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Xantech 490-85 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Xantech 490-85 verständlich ist.

Eine gänzliche Bedienungsanleitung von Xantech sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Xantech 490-85 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Xantech 490-85 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Xantech 490-85, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Xantech 490-85 - die uns die ersten Schritte während der Nutzung von Xantech 490-85 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Xantech 490-85 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Xantech 490-85 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Xantech 490-85?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Xantech 490-85 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Xantech 490-85 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)