Xantech 490-85の取扱説明書

10ページ 0.26 mb
ダウンロード

ページに移動 of 10

Summary
  • Xantech 490-85 - page 1

    08905105A - 1 - INSTALLATION INSTRUCTIONS 490-85 CLF / LCD Friendly Micr o Link IR Receiver DESCRIPTION The 490-85 is a CFL (compact fluoresc ent light) / LCD (liquid crystal di splay) version of the 490 Micro Link series IR receivers. It is specifically designed to have greater i mmunity to high frequency ballasted CFL and overhead fluorescent typ ...

  • Xantech 490-85 - page 2

    08905105A - 2 - IR CARRIER ADJUSTMENT The 490-85 is factory set to an IR carrier repeat frequency of 39kHz . This will be correct for the majority of installations. Howe ver, some manufacturer’s components that you wish to control may use different carrier frequencies (such as RCA DSS satell ite receivers that use 56kHz). If sure carrier frequenc ...

  • Xantech 490-85 - page 3

    08905105A - 3 - APPLICATION WIRING A typical system, with a 490-85, 781RG Power S upply and 283M Emitters plugged into a 791-44 Connecting Block, is shown in the figure below. 1. Plug the 3.5 mm stereo mini plug from the 490-85 into the 791-44 connecting block labeled “IR RCVR”. 2. Plug in the 3.5 mm mono mini plug from any of the 282, 284, 283 ...

  • Xantech 490-85 - page 4

    08905105A - 4 - IR Troubleshooting Guide NOTE: Due to the many variables in a given installa tion, the troubleshooting counter measures you will have to take may vary from job to job. Each insta llation is different due to the number of IR receivers in use, length of wire runs, type of wire, amount of ambient IR noise present, etc…. Therefore, yo ...

  • Xantech 490-85 - page 5

    08905105A - 5 - Symptom #2: TB LED on IR Receiver (and/or Emitters) Dimly lit or flickering Cause: Solution 1. Signal and ground wir es are reversed or shorted either at the connecting block or IR receiver. Recheck your wiring. 2. Defective emitter. Replace Emitter 3. Relatively high levels of ambient noise . This can be due to any of the following ...

  • Xantech 490-85 - page 6

    08905105A - 6 - Symptom #3: TB LED on IR Receiver (and/or Emitters) on solid Cause: Solution 1. Plasma Interference Use a 490-90 Plasma 'Friendly' Receiver. If already using a 490-90 unit, please note the Plasma interference can be reflected off of any item it comes into contact with within approx. 3ft. From the front of the display. Keep ...

  • Xantech 490-85 - page 7

    08905105A - 7 - Symptom #4: TB LED on IR Rec. blinks but 283M or 286M 'Blink' style Emitters do not Cause: Solution 1. There may be a short, such as a staple driven through the Signal and GND wires of the IR Receiver and/or the emitter. Recheck your wiring. 2. Emitter may be shorted internally Replace Emitter or use TEST EMITTER to check ...

  • Xantech 490-85 - page 8

    08905105A - 8 - Symptom 6: Emitters function but some (or all) components do not respond. Cause: Solution 1. Emitter placement is incorrect. Reposition the Emitter so that it is directly over the components sensor window. Consult the components owners manual of the unit for the exact location of the IR Sensor Window. 2. Emitter placement is correct ...

  • Xantech 490-85 - page 9

    08905105A - 9 - Symptom #7: Absolutely No Functionality (How to determine which component is at fault) Step: Component to Test Instructions 1. Verify Power Supply With a Multimeter, measure the DC Voltage of the supply while it is connected to the Connecting Block. Put the Negative lead of the meter on the terminal marked GND and the Positive Lead ...

  • Xantech 490-85 - page 10

    08905105A - 10 - 4. Verify IR Receiver. Remove the power supply from the connecting block and all Emitters from the output. Place a jumper wire on the connecting block between IR Signal and GND. Reconnect the Power Supply. With a known good hand-held remote, shoot a constant IR Command at the receiver and verify the TB LED on the Receiver lights. X ...

メーカー Xantech カテゴリー Radio

Xantech 490-85のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 490-85の取扱説明書
- Xantechの製品カード
- パンフレット
- またはXantech 490-85の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Xantech 490-85の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Xantech 490-85の取り付け説明書、サービスマニュアル、簡易説明書、またはXantech 490-85のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Xantech 490-85の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Xantech 490-85デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがXantech 490-85を使用するのを助ける技術的文書のことです。説明書は通常、全てのXantech 490-85ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Xantechの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Xantech 490-85の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははXantech 490-85の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Xantech 490-85に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Xantech 490-85デバイスの基本機能を使うにあたってのヒント。 Xantech 490-85のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Xantech 490-85に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるXantech 490-85のメーカー/サービスへの連絡先に関する情報。

Xantech 490-85についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもXantech 490-85の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがXantech 490-85で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)