Bedienungsanleitung Clifford 6000

13 Seiten 0.82 mb
Download

Zur Seite of 13

Summary
  • Clifford 6000 - page 1

    Standard Features of the IntelliGuard 600 0 Programmable (+) or (-) require relays . System Component s The IntelliGuard 6000 installation kit contains the following components : One Prewired 22-pin connector harnes s One Extended Range Receiver One Prewired 4-pin connector harness One Plain V iew 2 Coded V alet Switc h One IntelliGuard 6000 Contro ...

  • Clifford 6000 - page 2

    Wiring Description for the 4-Pin Connector Pi n Wire Colo r Con nects t o 1 Green/Blu e Ignition Outpu t 2 White/Blu e Starter Outpu t 3 White/Brow n Ignition Inpu t 4 White/Green Starter Inpu t Wiring Description for the 22-Pin Connecto r Pi n Wire Colo r Con nects t o 1 Gray/Blu e Channel 4 output 2 Black Prewired to the V alet Switch and Glass T ...

  • Clifford 6000 - page 3

    Passenger Compartment Connection s Control Unit and Extended Range Receive r The IntelliGuard 6000 con trol unit must be in stalled in side the ve hi cle. Un der no cir cum st a nces should the uni t be in stalled un der the hood or other simi larly hos tile en vi ron ment . 1 . Select an area behind the dash to mount the control unit using the sup ...

  • Clifford 6000 - page 4

    Passenger Compartment Connections (Continued ) Trunk Trigge r V ehicles with a ground-switching trunk light will interface directly with the IntelliGuard 6000 (o n positive switching Rolls - Royce vehicles , use a relay to invert polarity). The switch may be located in or near the trunk latch or at the tr u nk light. If a switch cannot b e located, ...

  • Clifford 6000 - page 5

    Engine Bay Connections (Continued ) Hood Trigge r V ehicles with a ground-switching hood light will interface directly with the IntelliGuard 6000 (on positive switching vehicles, use a relay t o invert polarity). The switch may be located in or near the hood latch or at the hood light. If a s witch cannot be located, you must add a pin switch in a ...

  • Clifford 6000 - page 6

    FACT—False Alarm Control and Tes t The system microprocessor automatically checks for another activated sensor or trigger before soun d ing the siren a second time, thus preventing any further false alarms. If you wish to test FAC T , simpl y , 1 . Arm the sys tem with the re mote con trol . 2 . W ait 10 seconds after the interior light turns off ...

  • Clifford 6000 - page 7

    Certificate of Installatio n After installation and testing has been completed, you mus t fill in the Clifford Electronics Certificate of Installatio n . Programmable Feature s IntelliGuard 6000 comes from the factory with its features preprogrammed as noted in bol d text in the tables on pages 8 and 9. Som e features can be programmed by the insta ...

  • Clifford 6000 - page 8

    User-Programmable Feature s User-Programmable Features (1 Chirp = OF F , 2 Chirps = ON ) Fea tur e Selec t Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4 ✱ 1 Add New Remote NOTE 1 Chirps (Off / O n /Quiet*) (1 chirp / 2 chirps /3 chirps ) *Quiet chirps are only available wit h SSPS Sire n AutoArmin g ( On /Off ) Arm/Disarm with Secondary Remot e NOT ...

  • Clifford 6000 - page 9

    Installer-Programmable Feature s T o access the installer-programmable features, use the procedure defined in the User-Programmable s ection, but after completing step 4, continue to press and hold the ✱ side of the Plain V iew 2 Switch for another 10 seconds. Y ou will hear three confirmatio n chirps indicating that the system is in installer-pr ...

  • Clifford 6000 - page 10

    System Checklist & Troubleshooting (Continued) n Arm the IntelliGuard 6000 (either from inside or outside the vehicle) and wait 10 seconds. T urn th e ignition to the “ON ” position. o Engine does not respond and alarm triggers. This is the correct response, proceed to step 3. o Engine starts or cranks. The starter im mo bi li sa tion cir c ...

  • Clifford 6000 - page 11

    System Checklist & Troubleshooting (Continued) Step 4. Test the park ing lights. Arm the sys tem . n T wo flashes . This is the correct response, proceed to step 5 . n One flash. If the parking lights flash only once, the IntelliGuard 6000 had pre vi ously AutoArmed it self pa s sively and by press ing the arm/disarm but ton the sys tem dis arm ...

  • Clifford 6000 - page 12

    System Checklist & Troubleshooting (Continued ) Step 8. Test the dis arm func tion . n Disarm the system. The following should occur : o Siren chirps onc e . If the siren does not chirp once, refer to step 3 . o Parking lights flash once. If the parking lights do not flash once, refer to step 4. o LED stops flashing . If not refer to step 6 . o ...

  • Clifford 6000 - page 13

    System Checklist & Troubleshooting (Continued ) Step 13 . Test the AutoArming By pass fea ture . Disarm the system. T urn the ignition to the “ON” position, then turn the ignition “OF F . ” n One Chirp . This is the correct response, wait 30 seconds after the interior lights have turned off to insur e the system does not passively arm. ...

Produzent Clifford Kategorie Automobile Alarm

Dokumente, die wir vom Produzenten des Geräts Clifford 6000 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Clifford
- Bedienungsanleitungen 6000
- Produktkarten Clifford
- Informationsbroschüren
- oder Energieetiketten Clifford 6000
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Clifford 6000.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Clifford 6000, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Clifford 6000. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Clifford 6000 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Clifford 6000, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Clifford 6000 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Clifford 6000 verständlich ist.

Eine gänzliche Bedienungsanleitung von Clifford sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Clifford 6000 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Clifford 6000 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Clifford 6000, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Clifford 6000 - die uns die ersten Schritte während der Nutzung von Clifford 6000 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Clifford 6000 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Clifford 6000 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Clifford 6000?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Clifford 6000 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Clifford 6000 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (1)

Гена

Нужна инструкция на русском языке. Где взять?