Bedienungsanleitung Hobart ML-104562 6460C

16 Seiten 2.45 mb
Download

Zur Seite of 16

Summary
  • Hobart ML-104562 6460C - page 1

    FORM 37005 (Apr. 2006) MODEL 6430T , 6460 & 6460T POT A T O PEELER MODEL ML-137602 6430T ML-19630 6460 ML-137604 6460T ML-104562 6460C ML-137606 6460CT 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart ML-104562 6460C - page 2

    – 2 – Installation, Operation and Care of MODEL 6430, 6430T , 6460 & 6460T PEELERS SA VE THESE INSTR UCTIONS GENERAL Models 6430 and 6430T Peelers are designed to peel 30 to 33 lbs (13.5 to 15.0 kg) of product in 1 to 3 minutes using a 3 / 4 HP, single- or three-phase electric motor. The 6430T includes a synchronous timer and is available f ...

  • Hobart ML-104562 6460C - page 3

    – 3 – PL-56337 D A T A PLA TE INLET TUBING DISPOSER FLANGE SWITCH HOPPER T OP BRACKET ASSEMBL Y SCREW TUBE COUPLING ABRASIVE DISC JUNCTION BO X CO VER AD APTER PLA TE DISPOSER CONDUIT HOLE R UBBER MOLDING PEEL TRAP DRA WER LOCK W ASHER AND W ASHER HARD W ARE JUNCTION BO X DISPOSER SWITCH PEELER PEEL TRAP DISPOSER ST AND Fig. 1 ...

  • Hobart ML-104562 6460C - page 4

    – 4 – LEXAN LINER 1. Slide the liner (Fig. 2) into the hopper, ensure the liner is under retaining brackets (Fig. 2) and resting on the top of the lip (Fig. 2) on the bottom of the hopper chamber. PL-41652-1 LINER RET AINING BRACKETS LIP PL-41653 KEEPER Fig. 2 Fig. 3 2. Push the liner keeper into the hole (Fig. 3) provided. 3. Secure the keeper ...

  • Hobart ML-104562 6460C - page 5

    – 5 – Assemble the legs as follows (Fig. 4): 1. Lay the peel trap on its side. 2. Assemble one of the rubber gaskets to one of the curved leg clamp bolts. 3. Assemble the bolt and gasket from the inside, through one of the leg bolt holes in the peeler housing. 4. Assemble a leg and a leg slot cover on the leg clamp bolt. 5. Place a stainless st ...

  • Hobart ML-104562 6460C - page 6

    – 6 – T o position peel trap draw er BENEA TH the discharge chute: T o position peel trap draw er to the RIGHT of discharge chute: T o position peel trap draw er to the LEFT of discharge chute: T o position peel trap draw er to the REAR of discharge chute: Remov e cov er disc and place drain hose through this hole. Remov e cov er disc and place ...

  • Hobart ML-104562 6460C - page 7

    – 7 – DISPOSER STAND If a disposer stand is to be used, unpack the stand from its shipping carton. The feet may be threaded in or out as necessary to level the disposer stand. The disposer flange, adapter plate, gaskets and all hardware required for mounting the disposer are assembled and packed in a separate container. Refer to the disposer ma ...

  • Hobart ML-104562 6460C - page 8

    – 8 – ELECTRICAL CONNECTIONS Before making electrical connections, check the specifications on peeler data plate (Fig 1), as well as those of the disposer (where applicable), to assure they agree with those of your electrical service. WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRIC ...

  • Hobart ML-104562 6460C - page 9

    – 9 – OPERA TION Using the lugs on the hopper top as locators, position the hopper top on the housing and turn it clockwise into place. Close and latch the discharge chute door. Pour the product into the hopper. There should be room in the hopper for the product to move around while peeling. Do NOT overload the peeler; peeler capacities are 30 ...

  • Hobart ML-104562 6460C - page 10

    – 10 – Turn on the water or disposer, if equipped, and thoroughly clean the interior of the hopper using a mild soap and brush. Turn off the water or disposer. If the drawer is equipped with a peel trap, remove the peel trap drawer and thoroughly clean the drawer, as well as the peel trap interior. The discharge chute MUST be left open when the ...

  • Hobart ML-104562 6460C - page 11

    – 11 – TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE Peeler won't operate. Electrical power not connected. Circuit breaker tripped or fuse blown. Excessive foaming. Too much water in the hopper. If the above suggestions do not remedy the situation, contact Hobart Service Office. SERVICE Contact your local Hobart-authorized Service Office for any ...

  • Hobart ML-104562 6460C - page 12

    – 12 – PL-56334 INSTALLATION DIAGRAM (WITHOUT TRAP) ...

  • Hobart ML-104562 6460C - page 13

    – 13 – PL-56333 INSTALLATION DIAGRAM (WITH TRAP) ...

  • Hobart ML-104562 6460C - page 14

    – 14 – PL-56335 INSTALLATION DIAGRAM (DISPOSER STAND) ...

  • Hobart ML-104562 6460C - page 15

    – 15 – NOTES ...

  • Hobart ML-104562 6460C - page 16

    – 16 – NOTES FORM 37005 (Apr. 2006) PRINTED IN THE U.S.A. ...

Produzent Hobart Kategorie Kitchen Utensil

Dokumente, die wir vom Produzenten des Geräts Hobart ML-104562 6460C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Hobart
- Bedienungsanleitungen ML-104562 6460C
- Produktkarten Hobart
- Informationsbroschüren
- oder Energieetiketten Hobart ML-104562 6460C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Hobart ML-104562 6460C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Hobart ML-104562 6460C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Hobart ML-104562 6460C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Hobart ML-104562 6460C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Hobart ML-104562 6460C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Hobart ML-104562 6460C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Hobart ML-104562 6460C verständlich ist.

Eine gänzliche Bedienungsanleitung von Hobart sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Hobart ML-104562 6460C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Hobart ML-104562 6460C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Hobart ML-104562 6460C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Hobart ML-104562 6460C - die uns die ersten Schritte während der Nutzung von Hobart ML-104562 6460C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Hobart ML-104562 6460C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Hobart ML-104562 6460C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Hobart ML-104562 6460C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Hobart ML-104562 6460C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Hobart ML-104562 6460C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)