English dropdown-ico

Manual Hobart ML-104562 6460C

16 pages 2.45 mb
Download

Go to site of 16

Summary
  • Hobart ML-104562 6460C - page 1

    FORM 37005 (Apr. 2006) MODEL 6430T , 6460 & 6460T POT A T O PEELER MODEL ML-137602 6430T ML-19630 6460 ML-137604 6460T ML-104562 6460C ML-137606 6460CT 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart ML-104562 6460C - page 2

    – 2 – Installation, Operation and Care of MODEL 6430, 6430T , 6460 & 6460T PEELERS SA VE THESE INSTR UCTIONS GENERAL Models 6430 and 6430T Peelers are designed to peel 30 to 33 lbs (13.5 to 15.0 kg) of product in 1 to 3 minutes using a 3 / 4 HP, single- or three-phase electric motor. The 6430T includes a synchronous timer and is available f ...

  • Hobart ML-104562 6460C - page 3

    – 3 – PL-56337 D A T A PLA TE INLET TUBING DISPOSER FLANGE SWITCH HOPPER T OP BRACKET ASSEMBL Y SCREW TUBE COUPLING ABRASIVE DISC JUNCTION BO X CO VER AD APTER PLA TE DISPOSER CONDUIT HOLE R UBBER MOLDING PEEL TRAP DRA WER LOCK W ASHER AND W ASHER HARD W ARE JUNCTION BO X DISPOSER SWITCH PEELER PEEL TRAP DISPOSER ST AND Fig. 1 ...

  • Hobart ML-104562 6460C - page 4

    – 4 – LEXAN LINER 1. Slide the liner (Fig. 2) into the hopper, ensure the liner is under retaining brackets (Fig. 2) and resting on the top of the lip (Fig. 2) on the bottom of the hopper chamber. PL-41652-1 LINER RET AINING BRACKETS LIP PL-41653 KEEPER Fig. 2 Fig. 3 2. Push the liner keeper into the hole (Fig. 3) provided. 3. Secure the keeper ...

  • Hobart ML-104562 6460C - page 5

    – 5 – Assemble the legs as follows (Fig. 4): 1. Lay the peel trap on its side. 2. Assemble one of the rubber gaskets to one of the curved leg clamp bolts. 3. Assemble the bolt and gasket from the inside, through one of the leg bolt holes in the peeler housing. 4. Assemble a leg and a leg slot cover on the leg clamp bolt. 5. Place a stainless st ...

  • Hobart ML-104562 6460C - page 6

    – 6 – T o position peel trap draw er BENEA TH the discharge chute: T o position peel trap draw er to the RIGHT of discharge chute: T o position peel trap draw er to the LEFT of discharge chute: T o position peel trap draw er to the REAR of discharge chute: Remov e cov er disc and place drain hose through this hole. Remov e cov er disc and place ...

  • Hobart ML-104562 6460C - page 7

    – 7 – DISPOSER STAND If a disposer stand is to be used, unpack the stand from its shipping carton. The feet may be threaded in or out as necessary to level the disposer stand. The disposer flange, adapter plate, gaskets and all hardware required for mounting the disposer are assembled and packed in a separate container. Refer to the disposer ma ...

  • Hobart ML-104562 6460C - page 8

    – 8 – ELECTRICAL CONNECTIONS Before making electrical connections, check the specifications on peeler data plate (Fig 1), as well as those of the disposer (where applicable), to assure they agree with those of your electrical service. WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRIC ...

  • Hobart ML-104562 6460C - page 9

    – 9 – OPERA TION Using the lugs on the hopper top as locators, position the hopper top on the housing and turn it clockwise into place. Close and latch the discharge chute door. Pour the product into the hopper. There should be room in the hopper for the product to move around while peeling. Do NOT overload the peeler; peeler capacities are 30 ...

  • Hobart ML-104562 6460C - page 10

    – 10 – Turn on the water or disposer, if equipped, and thoroughly clean the interior of the hopper using a mild soap and brush. Turn off the water or disposer. If the drawer is equipped with a peel trap, remove the peel trap drawer and thoroughly clean the drawer, as well as the peel trap interior. The discharge chute MUST be left open when the ...

  • Hobart ML-104562 6460C - page 11

    – 11 – TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE Peeler won't operate. Electrical power not connected. Circuit breaker tripped or fuse blown. Excessive foaming. Too much water in the hopper. If the above suggestions do not remedy the situation, contact Hobart Service Office. SERVICE Contact your local Hobart-authorized Service Office for any ...

  • Hobart ML-104562 6460C - page 12

    – 12 – PL-56334 INSTALLATION DIAGRAM (WITHOUT TRAP) ...

  • Hobart ML-104562 6460C - page 13

    – 13 – PL-56333 INSTALLATION DIAGRAM (WITH TRAP) ...

  • Hobart ML-104562 6460C - page 14

    – 14 – PL-56335 INSTALLATION DIAGRAM (DISPOSER STAND) ...

  • Hobart ML-104562 6460C - page 15

    – 15 – NOTES ...

  • Hobart ML-104562 6460C - page 16

    – 16 – NOTES FORM 37005 (Apr. 2006) PRINTED IN THE U.S.A. ...

Manufacturer Hobart Category Kitchen Utensil

Documents that we receive from a manufacturer of a Hobart ML-104562 6460C can be divided into several groups. They are, among others:
- Hobart technical drawings
- ML-104562 6460C manuals
- Hobart product data sheets
- information booklets
- or energy labels Hobart ML-104562 6460C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hobart ML-104562 6460C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hobart ML-104562 6460C, service manual, brief instructions and user manuals Hobart ML-104562 6460C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hobart ML-104562 6460C.

Similar manuals

A complete manual for the device Hobart ML-104562 6460C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hobart ML-104562 6460C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hobart ML-104562 6460C.

A complete Hobart manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hobart ML-104562 6460C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hobart ML-104562 6460C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hobart ML-104562 6460C, that we can find in the current document
3. Tips how to use the basic functions of the device Hobart ML-104562 6460C - which should help us in our first steps of using Hobart ML-104562 6460C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hobart ML-104562 6460C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hobart ML-104562 6460C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hobart ML-104562 6460C?

Use the form below

If you did not solve your problem by using a manual Hobart ML-104562 6460C, ask a question using the form below. If a user had a similar problem with Hobart ML-104562 6460C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)