Bedienungsanleitung FSP/Fortron Knight KN-1102TS

18 Seiten Betrifft nicht
Download

Zur Seite of 18

Summary
  • FSP/Fortron Knight KN-1102TS - page 1

    1K/2K/3K Online UPS Uninterruptible P ower Supply S ystem User Manual ...

  • FSP/Fortron Knight KN-1102TS - page 2

    T able of Contents 1. Importa nt Safety W arning ............................................................................................... 1 1-1. T ra nsportation ..................................................................................................... 1 1- 2. Prepar ation .......................................................... ...

  • FSP/Fortron Knight KN-1102TS - page 3

    1 1. Importan t Safety Warnin g Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and r ead carefully the following instructions before installing the unit. Do not operate this unit bef ore reading through all safety information and operating instructions carefully 1-1. Transportation  ...

  • FSP/Fortron Knight KN-1102TS - page 4

    2 1-5. Maintenance, service and faults  The UPS system operates wit h hazardous voltages. Repa irs may be carried out only by qualified maintenance personnel.  Caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet), components inside the UPS system are still connected to the battery and e ...

  • FSP/Fortron Knight KN-1102TS - page 5

    3 2. Installation and setup NOTE: Before installation, please inspect t he unit. Be sure that nothing inside the package is damaged. Please keep t he original package in a saf e place for f uture use. NOTE: There a re two diff erent t ypes of online UPS: standa rd a nd long-run mod els. Plea se ref er to the following model ta ble. Model T ype Mode ...

  • FSP/Fortron Knight KN-1102TS - page 6

    4 8. Output circuit break e r 9. Output terminal 2-2. Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three -wire, grounded recept a cle only . Avoid using extension cords. The power cord is supplied in t he UPS packag e. Step 2: UPS output connection  For socket -type outputs, simply connect devices to the ou tlets . ? ...

  • FSP/Fortron Knight KN-1102TS - page 7

    5 Step 5: Install software For optimal computer system protection, install UPS monitoring software t o fully configure UPS shutdown. Y ou may insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps b elow to download and install monitoring software from the internet: 1. Go to the website http://www.power-softw ...

  • FSP/Fortron Knight KN-1102TS - page 8

    6 3. Operations 3-1. Button operation Button Function ON/Mute Button  Turn on the UPS: Pre ss and hold ON/Mute button for at least 2 secon ds to turn on the UPS.  Mute the a larm: When the UPS is on ba ttery mod e, press and hold this button for at least 5 seconds to disa ble or e nable the alarm system. But it ’ s not applied to the situat ...

  • FSP/Fortron Knight KN-1102TS - page 9

    7 Display Function Remaining backup time information Indicates the remaining backup time in pie chart. Indicates th e remaining ba ckup time in numbers. H: hours, M: minute, S: se cond Fault information Indicates that the warning and fault occurs. Indicates the warning and fault codes, a nd the codes are listed in details in 3-5 section. Mute opera ...

  • FSP/Fortron Knight KN-1102TS - page 10

    8 3-3. Audible Alarm Battery Mode Sounding every 4 seconds Low Battery Sounding every second Overload Sounding twice every second Fault Continuously sounding Bypass Mode Sounding every 10 seconds 3-4. LCD display wordings index Abbreviation Display content Meaning ENA En able DIS Disable ESC Escape HLS High loss LLS Low loss BA T Battery CF Convert ...

  • FSP/Fortron Knight KN-1102TS - page 11

    9 the following output voltage: 10 0: presents output voltage is 100Vac 110: presents output volta ge is 110Vac 115: presents output voltage is 115Vac 120: presents output voltage is 120Vac 127: presents output voltage is 127Vac  02: Frequency Converter enable /disable Interface Setting Parameter 2 & 3: Ena ble or disable converter mode. You ...

  • FSP/Fortron Knight KN-1102TS - page 12

    10  06: Bypass enable/disable when UPS is off Interface Setting Parameter 3: Enable or disable Bypass function. You may choose the following two options: ENA: Bypass enable DIS: Bypass disable  07: Bypass voltage range setting Interface Setting Parameter 2 & 3: Set the acceptable high volta ge point and acceptable low voltage point for By ...

  • FSP/Fortron Knight KN-1102TS - page 13

    11 3-6. Operating Mode Description Operating mode Description LCD display Online mode When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output. T he UPS will also charge the battery at online mode. ECO mode Energy saving mode: When the input voltage is within voltage regulation range, UPS will bypass vo ...

  • FSP/Fortron Knight KN-1102TS - page 14

    12 3-8. Warning indicator W arning Icon ( flashing) Alarm Low Battery Sounding every second Overload Sounding twice every second Battery is not connected Sounding every second Over Charge Sounding every second Over temper ature Sounding every second Charger failure Sounding every second Out of bypass v oltage ra nge Sounding every second ...

  • FSP/Fortron Knight KN-1102TS - page 15

    13 4. Troubleshoo ting If the UPS s ystem does not oper ate correctly , please solve the problem by using the table below. Symptom Possible cause Remedy No indication and alarm even though the mains is normal. The AC input power is not connected well. Check if input power cord f irmly connected to the mains. The AC input is connected to the UPS out ...

  • FSP/Fortron Knight KN-1102TS - page 16

    14 Symptom Possible cause Remedy Battery backup time is shorter th an nominal v alue Batteries are not f ully charged Charge the bat teries for at least 5 hours and then check capacity . If the problem still persists, consult your dealer . Batteries defect Contact your dealer to replace the batt ery . F ault code is shown as 05 on LCD display . A t ...

  • FSP/Fortron Knight KN-1102TS - page 17

    15 5. Storage and M aintenance Operation The UPS system contains no user -serviceable parts. If the battery s ervice life (3~5 years at 25° C ambient temperature) has been exceeded, the batteries mus t be replaced. In this case , please contact your dealer. Storage Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool ...

  • FSP/Fortron Knight KN-1102TS - page 18

    16 6. Specifications CAPACITY* 1000 VA / 800 W 2000 VA / 1600 W 3000 VA / 2400 W INPUT Voltage Range Low Line Transfer 160VAC/140VAC/120VAC /110VAC± 5% ( based on load percentage 100% - 80 % / 80 % - 70 % / 70 - 60 % / 60 % - 0 ) Low Line Comeback 16 8VAC/14 8VAC/128VAC/1 18VAC ± 5 % ( based on load percentage 100% - 80 % / 80 % - 70 % / 7 0 - 60 ...

Produzent FSP/Fortron Kategorie Uninterruptible power supply (

Dokumente, die wir vom Produzenten des Geräts FSP/Fortron Knight KN-1102TS erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen FSP/Fortron
- Bedienungsanleitungen Knight KN-1102TS
- Produktkarten FSP/Fortron
- Informationsbroschüren
- oder Energieetiketten FSP/Fortron Knight KN-1102TS
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung FSP/Fortron Knight KN-1102TS.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen FSP/Fortron Knight KN-1102TS, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen FSP/Fortron Knight KN-1102TS. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts FSP/Fortron Knight KN-1102TS ansehen.

Die komplette Bedienungsanleitung des Geräts FSP/Fortron Knight KN-1102TS, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von FSP/Fortron Knight KN-1102TS hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von FSP/Fortron Knight KN-1102TS verständlich ist.

Eine gänzliche Bedienungsanleitung von FSP/Fortron sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von FSP/Fortron Knight KN-1102TS bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von FSP/Fortron Knight KN-1102TS befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich FSP/Fortron Knight KN-1102TS, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts FSP/Fortron Knight KN-1102TS - die uns die ersten Schritte während der Nutzung von FSP/Fortron Knight KN-1102TS erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit FSP/Fortron Knight KN-1102TS hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von FSP/Fortron Knight KN-1102TS im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich FSP/Fortron Knight KN-1102TS?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit FSP/Fortron Knight KN-1102TS nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit FSP/Fortron Knight KN-1102TS hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)